ADJ WiFLY EXR QA5 IP User Instructions page 7

WiFly EXR QA5 IP
Operating Power:
There are two ways to supply power to this unit; battery power or AC
power.
• AC Power - To run the unit using AC power, plug the unit into a
power source and activate the battery load on page 15. When using
AC power make sure the battery button is in the OFF position.
• Battery Power - To run the unit using Battery power, press the bat-
tery button located on the bottom of the fixture across from power
input connection. Follow the instructions on page 15 to activate the
battery load.
LCD Display Lock:
The display will lock after 30 seconds. Press and hold the MODE
button for at least 10 seconds to unlock the display and access the
menu.
Energy Saving Mode
This will decrease the LED's brightness gradually when the battery
life is less than 80%, this is will extend the battery life.
1. To activate energy saving mode, press the MODE button until
"BATT LEV" is displayed.
2. Press the SET UP button until "BATT LEV SAVE:XX" is displayed.
"XX" represents either "ON" or "OFF".
3. Press the UP or DOWN button so that "ON" is displayed. If "ON"
is displayed already then the fixture is already in energy saving
mode.
LED Display On/Off:
To set the LED display light to turn off after 20 seconds, press the
MODE button until "OPTION" is displayed. Press the SET UP button
so that BLGT:XXX" is displayed. "XXX" represents either ON or OFF.
Press the UP or DOWN buttons so that OFF is displayed. Now the
display light will turn off after 30s. Press any button to turn the dis-
play on again.
Operating Modes:
The WiFly EXR QA5 IP has six operating modes:
• Static Color Mode - There are 64 colors to choose from.
• RGBA Mode - Choose one of the four colors to remain static or
ADJ Products, LLC - www.adj.com - WiFly EXR QA5 IP User Manual Page 12
Operating Instructions WiFly EXR QA5 IP
adjust the intensity of each color to make your desired color.
• Auto Mode - Will run a mixture of color fade and change.
• Color Change Mode - There are 16 color change modes to choose
from.
• Color Fade Mode - There are 16 color fade modes to choose from.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
RGBA Dimmer Mode:
1. Plug the fixture in and press the MODE button until "MANUAL" is
displayed. Then press the SET UP button to scroll through RGBA
colors.
2. When "RED:XXX" is displayed you are in Red dimming mode.
Press the UP and DOWN buttons to adjust intensity.
3. When "GREN:XXX" is displayed you are in Green dimming
mode. Press the UP and DOWN buttons to adjust intensity.
4. When "BLUE:XXX" is displayed you are in Blue dimming mode.
Press the UP and DOWN buttons to adjust intensity.
5. When "AMBR:XXX" is displayed you are in Blue dimming mode.
Press the UP and DOWN buttons to adjust intensity.
6. After you have adjusted the RGBA colors to make your desired
color you can then activate strobing by pressing the SET UP but-
ton to enter the strobe mode.
7. "STROB.XX" will be displayed, this is strobe mode. The Flash can
be adjusted between 00 (flash off) to 15 (fastest flash).
Color Change Mode:
1. Plug the fixture in and press the MODE button until "JUMP RUN
SNAP:XX" is displayed. "XX" represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color change
mode.
3. Press the SET UP button and "SPEED:XX" will be displayed. Use
the UP and DOWN buttons to adjust the speed of the color
change.
Color Fade Mode:
1. Plug the fixture in and press the MODE button until "FADE RUN
FADE:XX" is displayed. "XX" represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color fade
ADJ Products, LLC - www.adj.com - WiFly EXR QA5 IP User Manual Page 13
Operating Instructions