Page 1
OPTIMA'ZigBee'Thermostat' Salus Controls Inc. User'Manual' 123 Townsend St. Level LL2 San Francisco, CA 94107 Version'1.0' For other language versions, please visit: www.salusinc.com...
Page 2
Salus OPTIMA'ZigBee'Thermostat' FCC'and'Industry'Canada' AFETY' NSTRUCTIONS RF Radiation Exposure statement: This equipment complies with FCC and Please read these instructions carefully before installing and using Industry Canada RF radiation exposure limits set forth for an uncontrolled the OPTIMA thermostat, and keep this guide in a safe place for future environment.
Page 3
Salus OPTIMA'ZigBee'Thermostat' iii' – • Do not expose the unit to voltage fluctuations more than +/- PPENDIX' EGULATORY' TATEMENTS 10%. FCC'Statements' WARNING: Changes or modifications to this unit not expressly approved by • Do not use solvents or aggressive cleaning agents. A dry, soft the party responsible for compliance could void the user’s authority to...
Day of Week No oral or written information or advice given by Salus or a Salus-authorized & Time representative shall modify or extend this warranty. If any term is held to be...
Page 11
ARRANTY Heat and Cool Indicates HVAC / heat-pump state. Salus Controls Inc. (“Salus”) warrants that for a period of two (2) years (“Warranty Period”) from the date of purchase by the consumer (“Customer”), Icons – Air Conditioner is on or Cooling this device, excluding batteries (“Product”), shall be free of defects in...
Salus OPTIMA'ZigBee'Thermostat' Indicator Meaning ROUBLESHOOTING System Mode Operating mode for the HVAC / heat pump system The thermostat does not call for heat and/or cooling. Off – System is OFF Check that the connector pins are straight • Cool – AC or Cooling mode Check that the thermostat is fully seated on the mounting plate.
Salus OPTIMA'ZigBee'Thermostat' Tools' PECIFICATIONS You may need the following tools to install the Optima thermostat. Temperature units °C or °F Operating temperature 32-113 °F (0-45 °C) • Smartphone or camera to take pictures Indoor temperature 32-99 °F (0-37 °C) • Phillips or flathead screwdriver measurement range •...
Page 14
Salus OPTIMA'ZigBee'Thermostat' When replacing an existing thermostat, the goal is to replicate the Reset'To'Defaults wiring of the old thermostat on the OPTIMA thermostat. The RESET button is located on the bottom surface of the OPTIMA and can only be accessed with a pin. When pressed, the RESET button •...
Salus OPTIMA'ZigBee'Thermostat' pairing process. Check with your connected home system Remove'Old'Thermostat' TIP:' Wrap' the' wire' ends' procedures for more details. Remove the old thermostat from the around'a'long'stick,'such'as' • Prepare connected home system to add a thermostat. wall, taking care not to allow the wiring a' pencil' to' keep' the' wires' to fall inside the wall.
Alkaline batteries are recommended as the Low Battery sensor is tuned to alkaline batteries. PAIR This menu item allows the Optima ZigBee thermostat to be Warning: Do not mix old and new batteries. Do connected to a compatible connected home system.
Salus OPTIMA'ZigBee'Thermostat' Daylight Savings Time Initial'Configuration' ON – Daylight Savings Time is observed (default) After inserting the batteries, the display will flash all the segments, OFF – Daylight Savings Time is NOT observed followed by the firmware version number, then display US / CA with a blinking US.
Salus OPTIMA'ZigBee'Thermostat' Attach'Thermostat'To'Mounting'Plate' CLOCK Time Zone – default is PST Attach thermostat Mounting Plate aligning NST – Newfoundland Time Zone √ connector pins plastic AST – Atlantic Time Zone √ retention posts and pushing the EST – Eastern Time Zone √...
Page 19
Salus OPTIMA'ZigBee'Thermostat' The Fan Mode will change to indicate the current mode of the fan, SING'THE' HERMOSTAT and the Fan Icon will appear when the fan is turned on. There will be The OPTIMA thermostat offers basic functions from the local controls, a slight delay between selecting Fan On mode and the fan turning on.
Page 20
Salus OPTIMA'ZigBee'Thermostat' Sliding your finger along any part of the slider ring (the silver circular To remove the HOLD state, simply change the set point temperature ring around the screen) other than the MODE and FAN/HOLD using the buttons or the slider ring. The thermostat will now accept locations will also change the set point temperature.