Subscribe to Our Youtube Channel
Related Manuals for Salus Optima ST880ZB
Summary of Contents for Salus Optima ST880ZB
- Page 1 Connected Wireless System Guide Module 4 – Wireless HVAC Thermostats SMC-GM-WCSG-M4-2019.10v1_2019-11-10...
-
Page 2: Table Of Contents
SALUS Connected Wireless System Guide Module 4 Contents: Wireless HVAC Thermostats Section Page Introduction Using this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 System Overview . -
Page 3: Introduction
Wireless System Guide has been divided into 5 volumes . Volume 1 is required for all wireless systems since it covers installation of the SG888ZB Gateway and the SALUS Smart Home application . The remaining volumes are specific to a particular group of controls . -
Page 4: System Overview
By connecting the SG888ZB Gateway to your home network, the system is connected to the worldwide web . Monitor or adjust your HVAC system from anywhere via the SALUS Smart Home application . If the connection to the internet is lost, the system continues to function with the settings selected . -
Page 5: St880Zb Optima Zigbee Thermostat
Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Included Parts Thermostat with Trim Plate Screws & Anchors Mounting Plate Optima Thermostat Wire Labels AA Alkaline Optima Thermostat User Manual Batteries Quick Start Guide Tools Required Power Drill #1 Phillips 1/16”... -
Page 6: Installation - Mounting & Wiring
Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Installation – Mounting & Wiring BEFORE BEGINNING the installation procedure, turn off power to the heating system . Step 1. Determine the desired wiring configuration for the ST880ZB Thermostat . The following chart shows the terminal designations for gas, electric or oil (Non-HP) and heat pump (HP) installations . - Page 7 Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Use the wall anchors and screws supplied with the To cover screw holes or paint disturbance from Optima Thermostat to attach the Mounting Plate the old thermostat, install the Trim Plate between to the wall, making sure the wires go through the the wall and the Mounting Plate .
- Page 8 Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Step 7. Configure the initial parameters • After the batteries are inserted, all segments will be briefly displayed on the LCD screen . • Next, the firmware version number will be displayed Country Selection •...
-
Page 9: Controls & Display
Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat • Align connector pins and retention posts • Push the Thermostat onto the Mounting Plate • BE SURE that the connector pins are not bent • BE SURE that the Thermostat is FULLY SEATED on the Mounting Plate Turn on the power to the HVAC System . -
Page 10: Home Screen
Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Home Screen The display returns to the default Home Screen after 3 seconds of inactivity. Display Indicator Description Room Temperature Room temperature at the thermostat sensor Indicates the state of the appliance Cooling demand is active Heat/Cool Icons Heating demand is active... -
Page 11: Pairing Instructions
Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Pairing Instructions While the Optima Zigbee Thermostat doesn’t need to be installed to be paired with a SG888ZB Universal Gateway, it should be at or near the intended installation location to account for potential signal interference. - Page 12 Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Step 5. Open the SALUS Smart Home application, select the drop-down menu from the upper right of the screen and select: All Devices Add New Device Step 6. Press Scan Devices .
- Page 13 Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Step 8. Enter a unique Step 9. Press “Please click Step 10. Choose from setup descriptive name to identify here to setup” . options specific to the device . each device .
-
Page 14: Time & Date
Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Time & Date The ST880ZB Optima Thermostat should be configured by an experienced or authorized installer. Table 2.1: Time Zones Newfoundland Standard Time Atlantic Standard Time Eastern Standard Time Central Standard Time Mountain Standard Time PST*... -
Page 15: Settings
Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Step 6. When DATE is displayed, Step 7. Set the Day (D) and Year Step 8. Use the +/- buttons the Month value (M) begins (Y) similarly, pressing MODE to to toggle between DST ON flashing . -
Page 16: Firmware Update
Module 4 – Wireless HVAC Thermostats Section 2 ST880ZB Optima Zigbee Thermostat Table 2.2: ST880ZB Optima Zigbee Thermostat – SETTINGS United States of America COUNTRY Canada O – Rev Valve Energized in Cooling (default) B – Rev Valve Energized in Heating HVAC TYPE FAN HG Fan operation for gas heating (default) -
Page 17: Factory Reset
Factory Reset When resetting the Optima Thermostat to its factory default settings, it is necessary to delete the device from the SALUS Smart Home Application . Step 1. Choose tile icon Step 2. Choose “Remove shared Step 3. Choose “Delete” from corresponding to the Optima room thermostat”... -
Page 18: St898Zb Optima S Thermostat
Module 4 – Wireless HVAC Thermostats Section 3 ST898ZB Optima S Thermostat Included Parts Thermostat with Trim Plate Screws & Anchors Mounting Plate Optima S Thermostat Wire Labels AA Alkaline Optima S Thermostat User Manual Batteries Quick Start Guide Tools Required Power Drill #1 Phillips 1/16”... -
Page 19: Installation - Mounting & Wiring
Module 4 – Wireless HVAC Thermostats Section 3 ST898ZB Optima S Thermostat Installation – Mounting & Wiring BEFORE BEGINNING the installation procedure, turn off power to the heating system . Step 1. Determine the desired wiring configuration for the ST880ZB Thermostat . The following chart shows the terminal designations for gas, electric or oil (Non-HP) and heat pump (HP) installations . - Page 20 Module 4 – Wireless HVAC Thermostats Section 3 ST898ZB Optima S Thermostat Step 4. Install the Mounting Plate . Use the wall anchors and screws supplied with the To cover screw holes or paint disturbance from Optima Thermostat to attach the Mounting Plate the old thermostat, install the Trim Plate between to the wall, making sure the wires go through the the wall and the Mounting Plate .
-
Page 21: Display Boot Sequence
Initial Configuration, described later in Section 3 . Step 1. Open the SALUS Smart Home application, select the drop-down menu from the upper right of the screen and select: All Devices Add New Device... - Page 22 ST898ZB Optima S Thermostat Step 2. Press Scan Devices . After pressing “Scan Devices”, Step 3. Choose the check box the SALUS Smart Home that corresponds to the device application scans for devices . to pair . Step 4. Enter a unique Step 5.
-
Page 23: Initial Configuration
Module 4 – Wireless HVAC Thermostats Section 3 ST898ZB Optima S Thermostat Step 7. Press “Finish” to complete pairing . Initial Configuration After pairing is complete, the ST898ZB Thermostat begins a configuration procedure • When the screen is displayed, use the +/- buttons to toggle between to select country in which the thermostat is installed . - Page 24 Module 4 – Wireless HVAC Thermostats Section 3 ST898ZB Optima S Thermostat Heat Pump Options • If is selected, the following options are available by pressing +/- O/B reversing valve terminal energized for cooling O/B reversing valve terminal energized for heating •...
-
Page 25: Home Screen & Controls
Module 4 – Wireless HVAC Thermostats Section 3 ST898ZB Optima S Thermostat Home Screen & Controls Indicator Description Mode Message Display Alphanumeric status display Simple/Full Time Display Time in 12- or 24-hour format if provided by the network Full Main Temperature Display Room temperature or setpoint as require Simple/Full Permanent Hold Status Icon Visible if Permanent Hold is active... -
Page 26: Operation
. See Configuring the Thermostat later in this section for more details . The SALUS Smart Home system can be used to set up a schedule on the device . Instructions for this are provided in Section 4, Thermostat Schedules . -
Page 27: Configuration
Module 4 – Wireless HVAC Thermostats Section 3 ST898ZB Optima S Thermostat Configuration Instructions for Thermostat configuration are intended for qualified installation/service professionals. Do not make adjustments without a thorough understanding of the HVAC system. Pressing the Settings Icon will begin cycling through all available configuration settings and three setup functions . - Page 28 Module 4 – Wireless HVAC Thermostats Section 3 ST898ZB Optima S Thermostat Settings / Functions (Continued): 6 - Frost Protection 7 - Temperature Offset Temperature below which the thermostat will call for Temperature added to measured temperature to heat regardless of mode . account for calibration issues .
-
Page 29: Remote Thermostat Operation & Parameters
Remote Thermostat Operation & Parameters Optima & Optima S Parameters – Smart Home Module 1 of the SALUS Wireless System Guide provides information about downloading and using the SALUS Smart Home application from your computer or smart device. Step 1. Press On the SALUS Step 2. -
Page 30: Schedules & Status Options
Remote Thermostat Operation & Parameters Schedules & Status Options – Smart Home Using the SALUS Smart Home application, users can choose between setting up temperature schedules and using the Status to determine the temperatures . This process is the same for both the ST880ZB, Optima, and ST898ZB, Optima S, Thermostat . - Page 31 Use a similar process to change back to “Linked to Schedule” . Individual thermostats can be set differently if accessed from the menu under Status . Schedule Setup – Smart Home Step 1. On the SALUS Smart Step 2. When the tile flips, Step 3. Scroll down to the...
- Page 32 Module 4 – Wireless HVAC Thermostats Section 4 Remote Thermostat Operation & Parameters Step 4. Choose the To duplicate a schedule of another thermostat on the network, press “Duplicate schedule”. A list of thermostats icon to edit the schedule . available to duplicate, similar to the above, will appear.
- Page 33 . Status for Thermostat Control – Smart Home Step 3. Choose a status Step 1. On the SALUS Smart Step 2. Scroll down to the for which to change the Home dashboard, click menu .
- Page 34 Module 4 – Wireless HVAC Thermostats Section 4 Remote Thermostat Operation & Parameters Step 4. Choose “Thermostats” Step 5. Choose the desired Step 6. Change the Heating from the House Check tab . Thermostat . and Cooling setpoints to the desired value .
- Page 35 The corresponding temperature To change current status, simply Choose your new status from values and any other click status on the SALUS Smart the choices shown . automations that are linked to Home dashboard . the new status will take affect .
-
Page 36: Troubleshooting
Module 4 – Wireless HVAC Thermostats Section 5 Troubleshooting Troubleshooting Information 1 . The thermostat does not call for heat and/or cooling . • Check that connector pins are straight and intact • Check that the thermostat is fully seated on the mounting plate . If the terminals are not fully engaged, the firmware cannot activate the relays .
Need help?
Do you have a question about the Optima ST880ZB and is the answer not in the manual?
Questions and answers