Extron electronics CS 3T User Manual
  1. Manuals
  2. Brands
  3. Extron electronics Manuals
  4. Speaker System
  5. CS 3T
  6. User manual
Extron electronics CS 3T User Manual

Extron electronics CS 3T User Manual

Speedmount ceiling speaker system
Hide thumbs Also See for CS 3T:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Setup Manual
User Guide
Speakers
CS 3T and CS 120P
CS 123T SpeedMount Ceiling Speaker System
68-2543-01 Rev. A
01 15

Advertisement

Table of Contents
loading

Related Manuals for Extron electronics CS 3T

Summary of Contents for Extron electronics CS 3T

  • Page 1 User Guide Speakers CS 3T and CS 120P CS 123T SpeedMount Ceiling Speaker System 68-2543-01 Rev. A 01 15...

  • Page 2: Safety Instructions

    Safety Instructions Safety Instructions • English Инструкция по технике безопасности • Русский WARNING: This symbol, , when used on the product, is intended to ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан alert the user of the presence of uninsulated dangerous voltage within the на...
  • Page 3 “Extron Safety and Regulatory Compliance ” on the Extron website. Guide Copyright © 2015 Extron Electronics. All rights reserved. Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks ®...

  • Page 4: Conventions Used In This Guide

    Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: Potential risk of severe injury or death. AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information.

  • Page 5: Table Of Contents

    Installing the CS 123T System — Single Installer 5 Installing the CS 120P in a Suspended Ceiling — Division of Labor ..........18 Installing the CS 3T in a Suspended Ceiling — Division of Labor ..........23 Installing the CS 120P in a Hard Ceiling .... 30 Painting the Baffle and Grille ......

  • Page 6: Introduction

    Introduction This section gives an overview of the Extron CS 123T SpeedMount Ceiling Speaker System, consisting of the CS 3T speakers and CS 120P enclosure. It also provides a list of system features and an application diagram. Topics include: •...

  • Page 7: Features

    Grille and bezel are available in white only and may be painted to match environment • Spring-loaded locking arms on the CS 3T for quick installation • Fast-installing enclosure speeds installation; no tile bridge necessary UL 2043 plenum rated enclosure •...

  • Page 8: Application Example

    Tx Rx Tx Rx 50/60 Hz INPUTS OUTPUTS AUDIO INPUTS OUTPUTS REMOTE HDMI HDMI Laptop Blu-ray Player STANDBY/ON PQLS HDMI OPEN/CLOSE FL OFF Figure 1. Application Diagram of a CS 123T Installation CS 3T and CS 120P User Guide • Installation...

  • Page 9: Installation

    • Using the CS 120P: When used with the CS 120P, the CS 3T can be placed in plenum environments. This is the only configuration that is UL 2043 rated.

  • Page 10: Installing The Cs 123T System - Single Installer

    NOTE: A set of fiberglass tile adapters is provided with both the CS 3T and the CS 120P. Only one set is needed to install the CS 3T with the CS 120P kit in a 1-inch (2.54 cm) thick fiberglass tile. The adapter works...
  • Page 11 Remove the adjacent ceiling tile — To facilitate the installation process, remove the tile adjacent to the ceiling tile where the CS 3T will be installed. If the CS 120P is being installed, skip to step 6. Otherwise, proceed to step 5.
  • Page 12 Insert the conduit into the cover plate opening using an appropriate conduit adapter, and secure the conduit to the plate as shown below. Pull the wires out of the conduit and through the cover plate. CS 3T and CS 120P User Guide • Installation...
  • Page 13 Insert the wires through the clamp and cover plate, as shown below. Tighten the clamp screws. Cable Clamp Adapter Cover Plate Secondary Cable Pass Through Loop Rear of Enclosure Figure 8. Routing the Cables Without a Conduit CS 3T and CS 120P User Guide • Installation...
  • Page 14 Tape x 4 Figure 10. Attach Four Tape Strips to the Baffle and Port Ring Adapter NOTE: The tape strips must lie flat against all surfaces, with no ridges or raised edges. CS 3T and CS 120P User Guide • Installation...
  • Page 15 Ne laissez aucun jeu entre les câbles de support. NOTE: Observe all applicable building codes and local ordinances when installing the speaker. Route the speaker wires — Route the speaker wires through the ceiling tile hole. CS 3T and CS 120P User Guide • Installation...
  • Page 16 Remove the speaker grille — Carefully remove the grille from the front of the CS 3T. NOTE: Grille hooks are provided for grille removal, if needed. Attach the speaker wires to the captive screw connector — ATTENTION: • Do not tin the wires. Tinned wires are not as secure in the connector and could be pulled out.
  • Page 17 17. Red Wire (+) from Amplifier Amplifier Black Wire (-) from Amplifier Test Points Signal Test Points Figure 17. Signal Test Points — Loop-through Configuration CS 3T and CS 120P User Guide • Installation...
  • Page 18 Insert the captive screw connector into the four-pole receptacle on the speaker. 2 feet x 4 feet Ceiling Tile 4 Pole Connector Figure 19. Connecting the Wire from the CS 120P to the Speaker CS 3T and CS 120P User Guide • Installation...
  • Page 19 Figure 20. Attaching the Speaker Wire to the Strain Relief Point NOTE: Skip step 19 if installing the CS 3T in an open back configuration. Attach the secondary support line (when mounting with the CS 120P configuration) — Attach the support line as shown below.
  • Page 20 Mount the CS 3T (see figure 21). Insert the CS 3T through the bottom of the hole in the ceiling tile that was cut in step 3 Tighten the four locking arm screws (clockwise) until the speaker is securely clamped to the ceiling.
  • Page 21 Replace the adjacent tile — Reinstall the adjacent tile that was removed in step 4 Set the rotary tap selector switch — Use a small screwdriver to set the tap selector switch to the appropriate setting. CS 3T and CS 120P User Guide • Installation...
  • Page 22 Install the grille. Position the outer perimeter of the grille into the groove of the speaker baffle. Six magnets pull the grille securely into place. Speaker Grille Figure 24. Installing the Speaker Grille NOTE: Grille hooks are provided for removal of the grille after installation. CS 3T and CS 120P User Guide • Installation...

  • Page 23: Installing The Cs 120P In A Suspended Ceiling - Division Of Labor

    For metric ceilings (600 mm by 600 mm or 600 mm by 1200 mm) cut off the tabs. Tabs (4) Removable Tabs Figure 26. Tabs on the CS 120P CS 3T and CS 120P User Guide • Installation...
  • Page 24 NOTE: A set of fiberglass tile adapters is provided with both the CS 3T and the CS 120P. Only one set is needed to install the CS 3T with the CS 120P kit in a 1-inch (2.54 cm) thick fiberglass tile. The adapter works...
  • Page 25 Insert the wires through the clamp and cover plate, as shown in figure 29. Tighten the clamp screws. Cable Clamp Adapter Cover Plate Secondary Cable Pass Through Loop Rear of Enclosure Figure 29. Routing the Cables Without a Conduit CS 3T and CS 120P User Guide • Installation...
  • Page 26 Tape x 4 Figure 31. Attach Four Tape Strips to the Baffle and Port Ring Adapter NOTE: The tape strips must lie flat against all surfaces, with no ridges or raised edges. CS 3T and CS 120P User Guide • Installation...
  • Page 27 Anchor ends to suitable solid secure points within the permanent building structure. Secondary Support Cables (3) Attach cables here and secure. SC 26T with PRE 120 Figure 33. Attaching Secondary Support Lines CS 3T and CS 120P User Guide • Installation...

  • Page 28: Installing The Cs 3T In A Suspended Ceiling - Division Of Labor

    5 Installing the CS 3T in a Suspended Ceiling — Division of Labor In a division of labor installation, an AV system contractor installs the CS 3T (final installation phase). Use the following procedure: NOTE: Observe all applicable building codes and local ordinances when installing the speaker.
  • Page 29 In the parallel configuration, all of the speakers downstream of the one being tested continue to function even when it is disconnected. This is especially useful in installations where the system can never be completely down, such as in a hospital setting. CS 3T and CS 120P User Guide • Installation...
  • Page 30 38. Red Wire (+) from Amplifier Amplifier Black Wire (-) from Amplifier Test Points Signal Test Points Figure 38. Signal Test Points — Loop-through Configuration CS 3T and CS 120P User Guide • Installation...
  • Page 31 Insert the captive screw connector into the four-pole speaker receptacle. 2 feet x 4 feet Ceiling Tile 4 Pole Connector Figure 40. Connecting the Wire from the CS 120P to the Speaker CS 3T and CS 120P User Guide • Installation...
  • Page 32 NOTE: Leave enough slack in the zip tie so that the speaker can be securely installed in the enclosure. Fig. A Fig. B Fig. C Zip Tie Secondary Tie off Point CS 3T and CS 120P User Guide • Installation...
  • Page 33 Mount the CS 3T (see figure 42). Insert the CS 3T through the bottom of the hole in the ceiling tile that was cut in step 2 Tighten the four locking arm screws (clockwise) until the speaker is securely clamped to the ceiling.
  • Page 34 Install the grille — Position the outer perimeter of the grille into the groove of the speaker baffle. Six magnets pull the grille securely into place. Speaker Grille Figure 44. Installing the Speaker Grille NOTE: Grille hooks are provided for removal of the grille after installation. CS 3T and CS 120P User Guide • Installation...

  • Page 35: Installing The Cs 120P In A Hard Ceiling

    : celle-ci pourrait ne plus être correctement en contact avec les aimants et donc ne pas être maintenue. Clean the outer perimeter of the baffle to be painted with a damp cloth. Paint the outer baffle. CS 3T and CS 120P User Guide • Installation...
  • Page 36 Assurez-vous que la peinture n’encrasse pas les perforations de la grille, au risque d’empêcher la diffusion correcte du son depuis l’enceinte. After the paint has completely dried, reattach the logo and scrim. CS 3T and CS 120P User Guide • Installation...
  • Page 37 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

This manual is also suitable for:

Cs 123tCs 120p

Table of Contents