Related Manuals for Extron electronics CS 26T
Summary of Contents for Extron electronics CS 26T
- Page 1 User Guide Speakers CS 26T and CS 120P CS 1226T SpeedMount Ceiling Speaker System 68-2161-01 Rev. A 08 13...
-
Page 2: Safety Instructions
Safety Instructions Chinese Simplified Safety Instructions • English （简体中文） 警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 WARNING: This symbol, , when used on the product, is intended to 电压， 有触电危险。 alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. 注... - Page 3 FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
-
Page 4: Conventions Used In This Guide
Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: A warning indicates a situation that has the potential to result in death or severe injury. Attention indicates a situation that may damage or destroy the product or ATTENTION: associated equipment. -
Page 5: Table Of Contents
Ceiling — Division of Labor ......15 Installing the CS 26T in a Suspended Ceiling — Division of Labor ......20 Installing the CS 120P in a Hard Ceiling .... 26 CS 26T and CS 120P User Guide • Contents... - Page 6 CS 26T and CS 120P User Guide • Contents...
-
Page 7: Introduction
(for metric systems, the CS 120P end tabs are cut off). • UL 2043 listed — The CS 1226T is UL 2043 listed (only when the CS 26T is used with the CS 120P). NOTE: The use of any other back can other than the CS 120P or those provided by Extron voids the UL 2043 rating. -
Page 8: Application Example
SI GN Extron XPA 2003C 70V Combo Power Ampli er Extron CS 1226T SpeedMount Ceiling Speaker System Extron SI 26 Surface-Mount Speakers Figure 1. Application Diagram of a CS 1226T Installation CS 26T and CS 120P User Guide • Introduction... -
Page 9: Installation
• Using the CS 120P: When used with the CS 120P, the CS 26T can be placed in plenum environments. This is the only configuration that is UL 2043 rated. -
Page 10: Installing The Cs 1226T System - Single Installer
NOTE: A set of fiberglass tile adapters is provided with both the CS 26T and the CS 120P. Only one set is needed to install the CS 26T with the CS 120P kit in a 1-inch (0.25 cm) thick fiberglass tile. The adapter works... - Page 11 Remove the cover plate — Loosen (do not remove) the two screws on the cover plate and remove it, as shown in figure 5. Cover Plate Figure 5. Removing the Cover Plate CS 26T and CS 120P User Guide • Installation...
- Page 12 Insert the wires through the clamp and cover plate, as shown in figure 7. Tighten the clamp screws. Cable Clamp Adapter Cover Plate Seismic Cable Pass Through Loop Rear of Speaker Figure 7. Routing the Cables Without a Conduit CS 26T and CS 120P User Guide • Installation...
- Page 13 Tape (x 4) Figure 9. Attach Four Tape Strips to the Baffle and Port Ring Adapter NOTE: The tape strips must lie flat against all surfaces, with no ridges or raised edges. CS 26T and CS 120P User Guide • Installation...
- Page 14 NOTE: Grille hooks are provided for grille removal, if needed. Configure the bass reflex port plate. By default, the CS 26T is set up for use with the CS 120P. If not using the CS 120P, set the plate for an open-back installation.
- Page 15 The source signal can be tested by connecting to the inner + (IN) and – (IN) terminals of the captive screw connector. Red Wire (+) from Amplifier Amplifier Black Wire (-) from Amplifier Test Points Figure 14. Signal Test Points — Parallel Configuration Signal Test Points CS 26T and CS 120P User Guide • Installation...
- Page 16 Wiring Multiple Speakers Using Loop-through: • A loop-through electrical connection is made on the crossover board of the CS 26T. Connect the wires to the captive screw connectors of the speakers, as shown in figure 15. Be sure to tighten the screws.
- Page 17 Insert the captive screw connector into the four-pole receptacle on the speaker crossover board. 2' by 4' Ceiling Tile 4 Pole Connector Figure 18. Connecting the Wire from the CS 120P to the Speaker CS 26T and CS 120P User Guide • Installation...
- Page 18 Attaching the Speaker Wire to the Strain Relief Point Mount the CS 26T (see figure 20). Insert the CS 26T through the bottom of the hole in the ceiling tile that was cut in step 3. Tighten the four screws (clockwise) until the speaker is securely clamped to the ceiling.
- Page 19 21. ATTENTION: Do not allow any slack in the support cables. NOTE: If the CS 26T will be installed in the CS 120P, do not attach secondary support cables to the speakers. Anchor ends to suitable solid secure points within the permanent building structure.
- Page 20 Install the grille. Position the outer perimeter of the grille into the groove of the speaker baffle. Six magnets pull the grille securely into place. Speaker Grille Figure 23. Installing the Speaker Grille NOTE: Grille hooks are provided for removal of the grille after installation. CS 26T and CS 120P User Guide • Installation...
-
Page 21: Installing The Cs 120P In A Suspended Ceiling - Division Of Labor
Installing the CS 120P in a Suspended Ceiling — Division of Labor In a division of labor installation, low-voltage contractors install the CS 120P enclosure (construction rough-in phase). NOTE: The ceiling grid must be installed before the installation of the CS 1226T can begin. - Page 22 NOTE: A set of fiberglass tile adapters is provided with both the CS 26T and the CS 120P. Only one set is needed to install the CS 26T with the CS 120P kit in a 1-inch (0.25 cm) thick fiberglass tile. The adapter works...
- Page 23 Insert the wires through the clamp and cover plate, as shown in figure 28. Tighten the clamp screws. Cable Clamp Adapter Cover Plate Seismic Cable Pass Through Loop Rear of Speaker Figure 28. Routing the Cables Without a Conduit CS 26T and CS 120P User Guide • Installation...
- Page 24 Tape (x 4) Figure 30. Attach Four Tape Strips to the Baffle and Port Ring Adapter NOTE: The tape strips must lie flat against all surfaces, with no ridges or raised edges. CS 26T and CS 120P User Guide • Installation...
- Page 25 32. ATTENTION: Do not allow any slack in the support cables. NOTE: If the CS 26T will be installed in the CS 120P, do not attach secondary support cables to the speakers. Anchor ends to suitable solid secure points within the permanent building structure.
-
Page 26: Installing The Cs 26T In A Suspended Ceiling - Division Of Labor
NOTE: A set of fiberglass tile adapters is provided with both the CS 26T and the CS 120P. Only one set is needed to install the CS 26T with the CS 120P kit in a 1-inch (0.25 cm) thick fiberglass tile. The adapter works... - Page 27 (IN) and – (IN) terminals of the captive screw connector. Red Wire (+) from Amplifier Amplifier Black Wire (-) from Amplifier Test Points Figure 35. Signal Test Points — Parallel Configuration Signal Test Points CS 26T and CS 120P User Guide • Installation...
- Page 28 Wiring Multiple Speakers Using Loop-through: • A loop-through electrical connection is made on the crossover board of the CS 26T. Connect the wires to the captive screw connectors of the speakers, as shown in figure 36. Be sure to tighten the screws.
- Page 29 Insert the captive screw connector into the four-pole receptacle on the speaker crossover board. 2' by 4' Ceiling Tile 4 Pole Connector Figure 39. Connecting the Wire from the CS 120P to the Speaker CS 26T and CS 120P User Guide • Installation...
- Page 30 Attaching the Speaker Wire to the Strain Relief Point Mount the CS 26T (see figure 41). Insert the CS 26T through the bottom of the hole in the ceiling tile that was cut in step 2. Tighten the four screws (clockwise) until the speaker is securely clamped to the ceiling.
- Page 31 Install the grille — Position the outer perimeter of the grille into the groove of the speaker baffle. Six magnets pull the grille securely into place. Speaker Grille Figure 43. Installing the Speaker Grille NOTE: Grille hooks are provided for removal of the grille after installation. CS 26T and CS 120P User Guide • Installation...
-
Page 32: Installing The Cs 120P In A Hard Ceiling
Do not leave a gap between the CS 120P and the ceiling material. NOTE: Installation in this type of ceiling must be done while access to the ceiling is still possible. CS 26T and CS 120P User Guide • Installation... - Page 33 Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to: USA, Canada, South America,...