Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for NetComm CD2004 Mega-i-Modem
Summary of Contents for NetComm CD2004 Mega-i-Modem
-
Page 2: Table Of Contents
9 Pin (RS-232 ) Serial Cable ......................25 USB cable ............................25 Appendix B: Registration and Warranty Information ....................26 Contact Information ..........................26 Copyright Information ..........................26 Customer Information ..........................26 Product Warranty ............................27 Limitations of Warranty ..........................27 www.netcomm.com.au YML830 Rev1 Page 2 CD2004 Mega-i 56K V.90 Modem User Guide... -
Page 3: Introduction
• Power Plug Pack 9V AC, 1.0 A • NetComm Driver, Manual and Utility CD Your NetComm Driver CD contains all the drivers, manuals and software that you will need to fully utilise your NetComm Modem. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide... -
Page 4: Step 1 - Hardware Installation
If you are using Windows XP or Windows 2000 and you intend on using your modem, please ensure that the modem is turned on before turning on your PC so that the operating system detects the modem on startup. www.netcomm.com.au YML830 Rev1 Page 4... -
Page 5: Step 2 - Software Installation
If this is the case these drivers can be used, however if you wish to use the NetComm drivers please continue with the following installation steps. 2. The drivers that Windows XP uses are not digitally signed by Microsoft and the following message will be displayed. -
Page 6: Windows® 2000
Select “CD-ROM drives” then click on “Next”. 4. A message will be displayed stating that the drivers have been found, click on “Next” to install the selected drivers. www.netcomm.com.au YML830 Rev1 Page 6 CD2004 Mega-i 56K V.90 Modem User Guide... - Page 7 Click “Yes”. 6. This completes the “Found New Hardware Wizard” click on “Finish” to complete the installation. 7. Your modem is now installed and ready to use. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 7...
-
Page 8: Windows® Me
4. A “Wave Device for Voice Modem” may now be located by Windows ME. 5. Select “Automatic search for a better driver (Recommended)” then select “Next” to start the install process. www.netcomm.com.au YML830 Rev1 Page 8 CD2004 Mega-i 56K V.90 Modem User Guide... - Page 9 “OK” to continue. 7. Windows will now install the drivers. Click on “Finish” to complete the driver install. 8. Your modem is now installed and ready to use. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 9...
-
Page 10: Windows®98
Select “CD-ROM drive” then click on “Next”. 4. A message will be displayed stating that the drivers have been found, click on “Next” to install the selected drivers. www.netcomm.com.au YML830 Rev1 Page 10 CD2004 Mega-i 56K V.90 Modem User Guide... - Page 11 8. You will now be required to specify the location of the drivers, these are located on the CD ROM supplied. Select “CD-ROM drive” and then click on “Next”. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 11...
- Page 12 files for your modem. Click on “Next” to continue. 10. Windows will now install the drivers. Click on “Finish” to complete the driver install. 11. Your modem is now installed and ready to use. www.netcomm.com.au YML830 Rev1 Page 12 CD2004 Mega-i 56K V.90 Modem User Guide...
-
Page 13: Windows®95
Select “CD-ROM drive” and then click on “Next”. 4. A message will be displayed stating that the drivers have been found, click on “Next” to install the selected drivers. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 13... - Page 14 5. This completes the “Add New Hardware Wizard” click on “Finish” to complete the installation. 6. Your modem is now installed and ready to use. www.netcomm.com.au YML830 Rev1 Page 14 CD2004 Mega-i 56K V.90 Modem User Guide...
-
Page 15: Driver Removal Process For The Cd2004
1. Click on “Start” then “Settings” and then “Control Panel” (Or simply “Start” then “Control Panel” for Windows XP and Windows 2000). 2. Double click on “Modems” (Or “Phone and modem options” for Windows XP and Windows 2000). 3. Select the “NetComm Mega-i-Modem 56k (CD2004)” and then click on “Remove”. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide... -
Page 16: Step 3 - Software Installation
Step 3 - Software Installation Now that you have installed your new NetComm modem and its drivers, you will need to install software to make your CD2004 a complete communications solution. Your NetComm Driver CD contains BVRP PhoneTools for Windows - Fax and Data software, and Adobe Acrobat Reader to view the manuals included in the Manuals directory of the CD. -
Page 17: Adobe Acrobat Reader
3. Click “OK” and the software installation screen will appear. Follow the screen instructions to install the software. A copy ofthe Adobe Acrobat User Guide is available in “D:\Manuals\Acrobat” where D:\ is the letter of your CD-ROM drive. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 17... -
Page 18: Step 4 - Using Bvrp Phonetools
All and New indicate the number of received documents. To view new received documents click “Inbox”. This will allow you to directly access the window that displays the Inbox folder contents. • Info displays warning messages and your modem’s status. www.netcomm.com.au YML830 Rev1 Page 18 CD2004 Mega-i 56K V.90 Modem User Guide... -
Page 19: Phone Features
Cuts your microphone off, allowing you to listen to your correspondent without being heard. Hold: Cuts your microphone and speaker off. Fax Reception Mode: Allows you to start receiving a fax. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 19... -
Page 20: Answering Machine
2. Depending on the answering machine mode you are using, select the greeting message to be issued in the drop-down list. Note: If you do not want to use the pre-recorded messages provided, you can record a custom greeting message. www.netcomm.com.au YML830 Rev1 Page 20 CD2004 Mega-i 56K V.90 Modem User Guide... -
Page 21: Record A Greeting Message
Received messages can also be accessed from the window that contains the Inbox folder. From there, simply select the message you want to listen to, and click the Listen icon. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 21... -
Page 22: Fax Features
3. Type in the recipients details or extract them from the Phonebook. 4. Various transmission options are available. To enable an option, click on the corresponding button. 5. Click Send to start the transmission. www.netcomm.com.au YML830 Rev1 Page 22 CD2004 Mega-i 56K V.90 Modem User Guide... -
Page 23: Faxing A File Directly From Phonetools
Faxing a document from any Windows application described above. Viewing and Printing Faxes Faxes can be viewed and printed not only from the Inbox and the Outbox, but also from the Confirm Transmission window. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 23... -
Page 24: Appendix A: Cable Connections
If you are unsure about which cable to use or which socket to connect it to, please refer to the hardware installation section in this manual. If you are still not sure about cable connections, please contact a professional computer technician or NetComm for further advice. RJ11 connector and cable An RJ-11 connector is the small, modular plug used for most analog telephones. -
Page 25: Pin (Rs-232 ) Serial Cable
If it is a new device, the operating system auto-detects it and asks for the driver disk. If the device has already been installed, the computer activates it and starts talking to it. USB devices can be connected and disconnected at any time. YML830 Rev1 www.netcomm.com.au CD2004 Mega-i 56K V.90 Modem User Guide Page 25... -
Page 26: Appendix B: Registration And Warranty Information
(3) The power supply that is provided with this unit is only intended for use with this product. Do not use this power supply with any other product or do not use any other power supply that is not approved for use with this product by NetComm. Failure to do so may cause damage to this product, fire or result in personal injury. -
Page 27: Product Warranty
4. The cost of transporting product to and from NetComm’s nominated premises is your responsibility; and, 5. NetComm does not have any liability or responsibility under this warranty where any cost, loss, injury or damage of any kind, whether direct, indirect, consequential, in ci den tal or otherwise arises out of events beyond NetComm’s reasonable control.
Need help?
Do you have a question about the CD2004 Mega-i-Modem and is the answer not in the manual?
Questions and answers