Front Drive Selector Actuator; Front Drive Selector Switch - Arctic Cat 2011 366 SE Service Manual

3. With the dimmer switch in the HI position, the meter
must show less than 1 ohm.
 NOTE: If the meter shows more than 1 ohm of resis-
tance, replace the switch.
RESISTANCE (LO Beam)
1. Connect one tester lead to the brown/black wire; then
connect the other tester lead to the white wire.
2. With the dimmer switch in the LO position, the
meter must show an open circuit.
 NOTE: If the meter reads resistance, replace the switch.
RESISTANCE (Emergency Stop)
1. Set the meter selector to the OHMS position.
2. Connect the one lead to the brown/lavender wire;
then connect the other tester lead to the black/white
wire.
3. With the switch in the OFF position, the meter must
show an open circuit.
4. With the switch in the RUN position, the meter must
show less than 1 ohm.
 NOTE: If the meter shows more than 1 ohm of resis-
tance, replace the switch.
RESISTANCE (Reverse Override)
1. Set the meter selector to the OHMS position.
2. Connect one tester lead to one lavender/red wire;
then connect the other tester wire to the green/red
wire. The meter must show less than 1 ohm.
3. Depress and hold the reverse override button. The
meter must show an open circuit.
 NOTE: If the meter does not show as specified,
replace the switch.
Front Drive Selector
Switch
The connector is the snap-lock one in front of the steering
post. To access the connector, the electric cover must be
removed.
 NOTE: Resistance tests should be made with the
connector disconnected and on the selector-side of
the connector.
RESISTANCE
1. Set the meter selector to the OHMS position.
2. Connect the one tester lead to the brown/lavender
wire; then connect the other tester lead to the white/
lavender wire.
3. With the selector switch in the 2WD position, the
meter must show less than 1 ohm.
80
4. With the selector switch in the 4WD position, the
meter must show an open circuit.
 NOTE: If the meter does not show as specified,
replace the front drive selector switch.
VOLTAGE
 NOTE: The battery must be connected when per-
forming voltage tests.
1. Set the meter selector to the DC Voltage position.
2. Connect the black tester lead to the negative battery
terminal.
3. Connect the red tester lead to the brown/lavender
wire on the harness side of the connector.
4. Turn the ignition switch to the RUN position.
5. The meter must show battery voltage.
 NOTE: If the meter shows other than specified,
check the harness, connector, 30 amp fuse, and bat-
tery connections.
Front Drive Selector
 NOTE: With the engine stopped and the ignition switch
in the ON position, a momentary "whirring" sound must
be noticeable each time the selector switch is moved to
2WD and 4WD. Test the switch, 30 amp fuse, and wiring
connections prior to testing the actuator.
VOLTAGE
1. Select the 2WD position on the front drive selector
switch; then disconnect the connector on the actuator
wiring harness.
2. With the ignition switch in the OFF position, connect
the black tester lead to the black wire in the supply
harness; then connect the red tester lead to the
brown/lavender wire in the supply harness.
3. Turn the ignition switch to the ON position. The
meter must show 12 DC volts.
4. Connect the red tester lead to the white/blue wire in
the supply harness. The meter must show 12 DC volts.
5. Select the 4WD position on the front drive selector
switch; then connect the red tester lead to the white/
blue wire in the supply harness. The meter must
show 0 DC volts.
 NOTE: The 4WD icon on the LCD should illuminate.
6. Connect the red tester lead to the brown/lavender
wire in the supply harness. The meter must show 12
DC volts.
 NOTE: If the voltage readings are as specified and
the actuator does not function correctly, replace the
actuator (see Drive System).
Manual
Table of Contents
Actuator