TABLE OF CONTENTS 1 – INTRODUCTION About this Manual ..........................1-1 Safety Messages Used in this Manual ....................1-1 Pre-Delivery Inspection ........................1-2 Front Axle Tire Alignment ....................... 1-2 Service and Assistance ........................1-2 Reporting Safety Defects ........................1-2 Occupant and Cargo Carrying Capacity Label ................. 1-3 Vehicle Certification Label .......................
Page 4
Table Of Contents Keys ..............................3-2 Remote Keyless Entry ........................3-2 Hazard Warning Flashers ........................3-3 Air Conditioner/Heater – Automotive (Dash) .................. 3-3 Radio In-Dash/Rearview Monitor System ..................3-3 Infotainment Center/GPS ........................3-4 Battery Boost Switch ........................3-6 Engine Cooling System ........................3-6 Diesel Exhaust Fluid Fill ........................
Page 5
Table Of Contents Electrical System – House 12-Volt DC .................... 6-7 House/Coach Battery Disconnect Switch ..................6-8 Battery Access ..........................6-8 Battery Care ............................6-9 Circuit Breakers and Fuses – House 12-Volt DC ................6-11 7 – PLUMBING Fresh Water System .......................... 7-1 Water Pump ............................
Page 6
Table Of Contents Slideout Emergency Retraction (Lippert) ..................10-4 General Slideout Care ........................10-6 11 – MAINTENANCE AND STORAGE Sealants – Inspection and General Information ................11-1 Roof ..............................11-1 Undercarriage ..........................11-1 Exterior Automotive Paint Finish ....................11-2 Exterior Graphic Care ........................11-4 Plastic Parts –...
The instructions included in this manual are intended as a guide, and in no way DANGER indicates a hazardous situation extend the responsibilities of Winnebago which, if not avoided, will result in death or Industries beyond the standard written serious personal injury.
National Highway Traffic Safety Administration delivery inspection of the chassis and all (NHTSA) in addition to notifying Winnebago motorhome components. Industries, Inc. As a part of the pre-delivery inspection...
SECTION 1 – INTRODUCTION or go to their website at http://www.safercar.gov or write to: Administrator, NHTSA 1200 New Jersey Avenue S.E. Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from the NHTSA website at http://www.safercar.gov OCCUPANT AND CARGO CARRYING CAPACITY LABEL This label is affixed in the driver’s area next to...
These pressure levels must be maintained to assure proper handling, safety, 2. Chassis manufacture date. and fuel economy. 3. Month and year of manufacture at Winnebago ® 9. Rear Axle Wheel Configuration: Single or Industries Dual as it relates to the inflation.
( 26.4 gal.) Notes: All information is based upon the most recent data available. Visit the Winnebago Industries, Inc. web page – www.winnebagoind.com – for the most current product information. The height of each model is measured to the top of the tallest standard feature and is based on the curb weight of a typically equipped unit.
Motorhome Serial Number ___________________________________________________________ Chassis Vehicle Identification No. (VIN) ________________________________________________ Vehicle Mileage at Delivery __________________________________________________________ Selling Dealer Name ________________________________________________________________ Address __________________________________________________________________________ __________________________________________________________________________ ® YOUR WINNEBAGO INDUSTRIES DEALER /SERVICE CENTER Name ____________________________________________________________________________ Address __________________________________________________________________________ __________________________________________________________________________ Contact ____________________________________________Phone ________________________ CHASSIS SERVICE CENTER...
SECTION 2 – SAFETY AND PRECAUTIONS GENERAL WARNINGS DRIVING SAFETY • Only seats equipped with seat belts are to be occupied while the vehicle is moving. WARNING • Make sure all passengers have seat belts fastened. Lap belts should fit low on the hips and upper thighs.
SECTION 2 – SAFETY AND PRECAUTIONS • Do not adjust tilt steering in a moving vehicle. • Do not operate the cruise control on icy or WARNING extremely wet roads, winding roads, in heavy traffic, or in any other traffic situation where a constant speed cannot be maintained.
SECTION 2 – SAFETY AND PRECAUTIONS • Open doors and other ventilating openings. • Leave the area until odor clears. DAN GE R • Have the propane system checked and leakage source corrected before using again. Do not use gas cooking appliances for Failure to comply could result in death or comfort heating.
It will detect CO gas from any combustion ® Winnebago Industries dealer. source such as the furnace, gas range/oven, water heater, refrigerator, chassis engine, and electric Further Information generator engine.
RV application. We that is also listed for RV application. We recommend obtaining a replacement from your recommend obtaining a replacement from your ® ® Winnebago Industries dealer. Winnebago Industries dealer. Further Information Further Information Please read the information provided by the See the manufacturer’s information in your...
SECTION 2 – SAFETY AND PRECAUTIONS Escape Window (Lift both red safety latch handles UP and push window OUT) -Typical View Slider Window Latch (Lift latch UP and slide window open) -Typical View Most slider windows along the side of any motorhome can also be used as alternate emergency exits, should the need arise.
SECTION 2 – SAFETY AND PRECAUTIONS MOLD, MOISTURE, AND YOUR MOTORHOME WARNING What is Mold? Keep all persons clear of the slideout Molds are part of the natural environment. room and moving parts while extending or They are as old as the Earth itself and mold retracting.
Winnebago Industries ® and have created a safe environment. If Winnebago Industries determines that mold For your safety, it is not recommended that ® ® is present in the Winnebago...
SECTION 2 – SAFETY AND PRECAUTIONS • Do not overload. Ladder is intended for one • If you must change lanes to get to a safe person. stopping place, use your signals to warn other motorists and change lanes smoothly and •...
Vehicle Certification Label. This will allow the towing operator to determine the proper towing equipment to use. ® Winnebago Industries does not assume Steel Wheel Front Steel Wheel Rear responsibility for damage incurred while towing this vehicle.
Page 24
SECTION 2 – SAFETY AND PRECAUTIONS Check for valve stem location and the valve stem clearance notch (located on the back side of the front cover). Chassis Supplied Wheel and Center Cover When re-installing the front liner, make sure to align the stem clearance notch on the back of the liner with the valve stem.
SECTION 2 – SAFETY AND PRECAUTIONS Further Information WHEELS – STYLIZED See the chassis manufacturer’s user guide ALUMINUM provided in your InfoCase for complete ® (Mercedes-Benz Sprinter Chassis) instructions and re-torque information. – If Equipped The Alloy Wheels, hub covers, and push on WARNING nut covers are mounted with the chassis supplied lug nuts which are concealed by push on nut...
Page 26
SECTION 2 – SAFETY AND PRECAUTIONS Removing the Wheel Note: Reference the chassis manufacturer’s user guide provided in your InfoCase for complete instructions and cautions on changing a wheel. 1. Once the vehicle is prepared for wheel removal, obtain the adapter from the co-driver Six Chassis Supplied Lug Nuts with attached foot well compartment and engage the adapter washers (located in the co-driver foot well...
SECTION 2 – SAFETY AND PRECAUTIONS ENGINE OVERHEAT If you see or hear steam escaping from the engine compartment or have any other reason to suspect an extreme engine overheating condition, pull the vehicle over to the roadside as soon as it is safe to do so, stop the engine, and get all passengers out of the vehicle.
SECTION 3 – DRIVING YOUR MOTORHOME may have a greater chance of being injured in an accident if they are seated in a child restraint WARNING system which is not properly secured. A child restraint system is designed to be secured in a vehicle seat by a lap belt or the lap Snug and low belt positions are essential.
SECTION 3 – DRIVING YOUR MOTORHOME Make a habit of having the keys with you This system is also featured with a rearview when you exit the vehicle and if opening the cab camera monitor system, which lets you see what door first before opening the entry door is directly behind your coach for safety and whenever unlocking with the keyless remote.
SECTION 3 – DRIVING YOUR MOTORHOME See the receiver manufacturer’s information while parked. This prevents accidental draining in your InfoCase for programming and operating of the chassis battery by prolonged use of the instructions. radio. NOTE:The House/Coach Battery Disconnect USB Cable switch must be ON while listening to the -If Equipped dash radio, as the audio relay is powered...
Page 33
SECTION 3 – DRIVING YOUR MOTORHOME Basic Operating Instructions Bluetooth Refer to the manufacturer’s owner manual Your coach is equipped with a Bluetooth and/or quick start guide provided in your microphone built into the radio system for hands- InfoCase for a complete explanation of features free cell phone usage.
SECTION 3 – DRIVING YOUR MOTORHOME Radio Power Switch The Radio Power switch lets you connect the dash radio to the coach batteries with the ignition switch turned off for listening while parked. This prevents accidental draining of the chassis battery with prolonged use of the radio.
SECTION 3 – DRIVING YOUR MOTORHOME VALVE STEM ACCESS ® (Mercedes-Benz Sprinter Chassis) Front Wheel Valve Stem Access on 18-Hole Steel Wheel with Push-On Full Wheel Trim –If Equipped 1. Obtain a double angle push/pull truck tire gauge. Diesel Exhaust Fluid Fill (Located under front hood) -Typical installation shown Further Information...
Page 36
SECTION 3 – DRIVING YOUR MOTORHOME Inner rear dual Hose extension 4. Using the hose extension as a remote handle, 6. When tire pressure testing is complete, unscrew the valve stem cap (retaining cap in reinstall the valve stem cap (with the cap still the end of the hose extension).
SECTION 3 – DRIVING YOUR MOTORHOME end, remove valve stem cap, insert valve stem extension into hose extension, and reinstall valve stem extension onto valve stem until snug. Pull off hose extension and re-insert valve stem cap into end of hose. 5.
Page 38
SECTION 3 – DRIVING YOUR MOTORHOME checked and adjusted after you have fully loaded the motorhome according to your personal needs. Thereafter, the alignment should be periodically inspected to help prevent uneven tire wear. Any excessive or abnormal tire wear may indicate worn or misaligned suspension or steering, unbalanced tire, or other tire/suspension problem.
SECTION 4 – APPLIANCES AND SYSTEMS The appliances installed in your motorhome are manufactured by reputable RV appliance makers and have been tested by independent laboratories to meet all applicable standards and codes set for RV appliances. See Section 2 - Safety and Precautions of this manual for any safety and precautions you need to take regarding the operation of your appliances.
SECTION 4 – APPLIANCES AND SYSTEMS Basic Operation Further Information For further information and operating cautions, see the refrigerator operating instructions included in your InfoCase. REFRIGERATOR SERVICE ACCESS COMPARTMENT (Exterior) • ON/OFF Switch The exterior refrigerator service compartment allows access to the rear of the refrigerator for inspection, maintenance, and service.
SECTION 4 – APPLIANCES AND SYSTEMS Refrigerator Access Compartment Refrigerator Access Compartment *Shown with cover removed -Typical View -Typical View RANGE TOP REFRIGERATOR SERVICE ACCESS COMPARTMENT The range in your motorhome operates on propane gas and will provide most of the (Exterior) functions of the range in your home.
SECTION 4 – APPLIANCES AND SYSTEMS DAN GE R NOTICE Do not use gas cooking appliances for Turn off the range and allow it to cool comfort heating. May lead to carbon before closing the range cover. The range monoxide poisoning, which can lead to cover is made of glass and may shatter death or serious injury.
SECTION 4 – APPLIANCES AND SYSTEMS Further Information See the manufacturer’s user guide provided in your InfoCase for instructions on replacement of light bulbs and replacement or cleaning of grease filter elements. Gen Start Gen Stop Hourmeter Typical - Your coach may or may not be equipped with all of the features shown.
SECTION 4 – APPLIANCES AND SYSTEMS • An interior light should be turned on to provide a small load which draws off the battery surface charge. Water Heater Switches Sensors See Water Heater information elsewhere in this section for operating instructions. Water Tank -Typical View Tank Capacities...
SECTION 4 – APPLIANCES AND SYSTEMS For Electric Operation WATER HEATER - GAS/ Press the Water Heater Electric switch to ON. ELECTRIC The shoreline must be connected or generator running for electric operation. The Gas/Electric Water Heater has a dual power feature.
SECTION 4 – APPLIANCES AND SYSTEMS • Lift handle straight out to open P-T valve when water heater is cold Water Heater Exterior Service Access -Typical View -Typical View 4. Let the handle of the P-T valve snap shut. Normally there is an air gap at the top of the water heater tank, which acts as a pressure buffer.
SECTION 4 – APPLIANCES AND SYSTEMS 2. Slide the Thermostat switch from OFF to Heat furnace for the first time to avoid a and press the Temp Selector button (up/down nuisance smoke alarm. arrows) until the desired temperature is shown We do not recommend removing the on the display.
SECTION 4 – APPLIANCES AND SYSTEMS efficiency of the Heat Pump. The Heat Pump will NOTE: The ducted roof air conditioning system not operate when the outside temperature falls has ceiling registers that can be closed if below 36 degrees F. necessary to force more cool air toward a specific area of the coach or to route To Operate the Heat Pump...
SECTION 5 – PROPANE GAS PROPANE GAS SUPPLY WARNING The propane gas system supplies fuel for the gas range/oven, water heater, furnace, and refrigerator (while in gas mode). When used and Do not alter or remove propane tank handled properly, this system is safe and valves or gauge.
Page 50
SECTION 5 – PROPANE GAS WARNING Do not fill propane container(s) to more than 80 percent of capacity. A properly filled container contains approximately 80 percent of its volume as liquid propane. Overfilling the propane container(s) can result in uncontrolled propane flow, which could lead to a fire or explosion and result in death or serious injury.
SECTION 5 – PROPANE GAS propane gas outlets in the United States do not Here are a few precautions to observe that will offer any other type of liquefied petroleum gas help you to use the propane gas system safely: than propane to the general public.) Check local •...
SECTION 5 – PROPANE GAS water heater. They contain carbon monoxide, PROPANE GAS WARNINGS which is an odorless, colorless, and poisonous AND PRECAUTIONS gas. It is illegal for vehicles equipped with propane tanks to travel on certain roadways or through WARNING certain tunnels in the U.S.
SECTION 5 – PROPANE GAS Only your dealer or a qualified propane gas service should remove the regulator cover for adjustments. WARNING Visually inspect the pressure regulator vent periodically for blockage by accumulated debris or insect nests, etc. Vent obstruction could result in excessive pressure causing fire or explosion, which could result in death or serious injury.
Page 54
SECTION 5 – PROPANE GAS This means that in extremely cold weather when a large volume of gas is being used by the furnace for heating, it is possible to experience a loss of gas pressure. At first, this problem may appear to be caused by an empty tank or a regulator freeze-up, but is actually caused by failure of the liquid gas to vaporize as fast as it is needed by the furnace.
SECTION 6 – ELECTRICAL Your coach is equipped with an electrical the power converter automatically changes a system consisting of two separate voltages: portion of the 120-volt current to 12-volt DC current. All equipment in the motorhome that is • 12-volt DC system (battery current);...
Page 56
SECTION 6 – ELECTRICAL 30 Amp Receptacle WARNING • Swivel cover section to access cord notch This connection is for 110/125 Volt AC, 60 Hz 30 Ampere supply. Do not exceed circuit rating. Exceeding the circuit rating may cause a fire and result in death or serious injury.
SECTION 6 – ELECTRICAL Inverter Control Panel INVERTER UNIT – 1000W –If Equipped –If Equipped The inverter has a wall-mounted monitor/ The inverter changes 12-volt DC battery control panel. It will also display warnings for power into 120-volt AC power for use by 120- overload conditions or other operating failure volt AC equipment inside the coach.
SECTION 6 – ELECTRICAL condition of the battery. If it is below “full 12-Volt 120-Volt charge”, the Charging Section will start charging House Fuses Circuit Breakers the batteries. If the house batteries have been extremely discharged, they will accept charge at a relatively high amperage rate.
SECTION 6 – ELECTRICAL “Off” and back to “On”. If the breaker is If the GFCI keeps tripping, have the electrical continually tripped and no overload is evident, system checked and repaired, if necessary, before have the system checked for a short in the wiring using again.
SECTION 6 – ELECTRICAL To use the 120-volt Generator, plug the power cord into the Generator receptacle within the utility compartment before starting the Generator. LP Generator Start/Stop Buttons (Located on monitor panel) -Typical View Generator Hourmeter The Generator hourmeter registers the total Generator Power Cord number of hours that the Generator has been...
SECTION 6 – ELECTRICAL To Stop the Generator • Park the vehicle so that the wind will carry the exhaust away from the vehicle. Also, note the • Press the Display ON/Gen OFF button. position of other vehicles to be sure their exhaust will not enter your vehicle.
SECTION 6 – ELECTRICAL The house batteries supply power to 12-volt equipment located in the living area of the motorhome. This includes the following 12-volt powered components (if equipped): interior 12- volt lighting, range exhaust fan, propane furnace fan, fresh water pump, systems monitor panel, refrigerator, roof vent fans, and 120-volt electrical generator starter.
SECTION 6 – ELECTRICAL House Batteries Chassis Battery Connector Chassis Battery (Located to the right of the The chassis (starting) battery is located in a accelerator pedal) compartment “well” in the floor beneath carpet Further Information ahead of the driver seat. See the chassis manual provided in your InfoCase for details on access and servicing.
Page 64
SECTION 6 – ELECTRICAL The two best defenses against sulfating Further precautions are: and insufficient charge are to: • Check the state of charge periodically to avoid discharge or sulfating. 1. Turn off the House/Coach Battery Disconnect switch to avoid parasitic discharge (the trickle To ensure that the battery will always accept discharge caused by directly connected and hold a charge, follow these simple...
Chassis Battery If your coach is going to be unoccupied for ® two weeks or more, Winnebago Industries recommends disconnecting the chassis battery in your coach to avoid battery discharge. Unplug the Chassis Battery Connector Functional...
Page 66
SECTION 6 – ELECTRICAL Automotive Chassis 12-Volt CIrcuit Breakers (Located on outboard side of passenger seat) * Shown with cover removed -Typical View 6-12...
SECTION 7 – PLUMBING FRESH WATER SYSTEM The Fresh Water System provides water to the galley sink, shower, bathroom lavatory, toilet, and water heater. Water may be supplied by either of two sources: • A fresh water tank and water pump located within the motorhome, or •...
Page 68
SECTION 7 – PLUMBING Fresh Water Valve Fresh Water Valve (Located in water service center) (Located in water service center) -Typical View -Typical View 4. Turn city water supply ON. Using City Water 5. Use the level display on the monitor panel to When connected to an outside source of water, oversee filling of the tank, or when the tank is the water bypasses the water pump and storage...
SECTION 7 – PLUMBING Using Tank Water (Gravity Fill) NOTE: Ensure the Fresh Water valve is in NORMAL position to use the water • Turn Water Pump switch ON. While the pump. If the valve is in Tank Fill position, switch is on, the water pump will the pump will run continuously without automatically supply tank water as needed.
Page 70
SECTION 7 – PLUMBING Initial Waterline Priming 1. Ensure that all water drain valves are closed, including water heater valve. 2. Turn Water Pump switch to “OFF” position. 3. Fill water tank. 4. Open all faucets, hot and cold. 5. Turn ON the Water Pump switch. 6.
SECTION 7 – PLUMBING Replacing the Cold Water Filter Cartridge You should replace the filter cartridge every season and when water flow from the faucet is too slow for convenience. The cartridge must be replaced at least every 12 months. •...
SECTION 7 – PLUMBING of tank capacity. This procedure will result in a residual chlorine concentration of 50 ppm in the water system. If a 100 ppm concentration is desired as discussed in Step 4, use 1/2 cup of household bleach with 1 gallon of water to prepare the chlorine solution.
SECTION 7 – PLUMBING SHOWER HOSE VACUUM BREAKER After using the shower, you may notice water dripping from the shower faucet assembly. The dripping results when vacuum in the shower hose (after closing the shower faucet) slowly releases and allows water remaining in the hose to drain Important “Don’ts”...
SECTION 7 – PLUMBING Dumping Holding Tanks appropriate waste water disposal site. This means you can use the toilet, sinks, and shower even in 1. Remove sewage drain hose from front driver areas where utility hookups are not available. side compartment. The black water holding tank contains the sewage from the toilet and may include bathroom lavatory on some models.
Page 75
SECTION 7 – PLUMBING Gray Waste Tank Drain Valve Black Waste Tank Drain Valve (Located beneath rear driver side of coach) (Located in driver side compartment) -Typical View -Typical View NOTE: DO NOT OPEN BOTH VALVES AT ONCE. Do not open the Gray Waste Tank Drain valve until the black tank is drained and Black Waste Tank Drain valve is closed to avoid sewage back-up...
SECTION 7 – PLUMBING WARNING Service inlet access must be closed when utility connections are not in use. When using a sewer hook-up, keep the dump valves closed until a tank becomes full or when preparing to leave the site. This keeps the solids in suspension, allowing them to be carried out with the liquids when the dump valve is opened.
SECTION 7 – PLUMBING See the “Water System Drain Valve Locations” chart at the end of this section for locations on your model. Normal By-Pass Flow Mode C AUT I ON Waterline Drain Valves Leave bypass valve handle in NORMAL -Typical View FLOW position if draining water and blowing out waterlines.
Page 78
SECTION 7 – PLUMBING press the backflow valve “button” in the center of the inlet to drain any water trapped in the inlet line. 5. Open Faucets. Turn on the water pump and open all sink faucets and shower head knobs. Leave open after water stops flowing.
Page 79
A “blow-out” plug can be Do not add automotive antifreeze or ® ® purchased at any Winnebago or Itasca caustic chemicals such as bleach or dealer. laundry detergents into the toilet bowl or holding tanks. Although these products...
Page 80
SECTION 7 – PLUMBING • Place a container beneath the filter to catch any water remaining in the waterlines during Method 2 – Antifreeze Fill filter removal. Procedure • Twist the filter cartridge “counter- (Fill plumbing lines with RV water system clockwise”...
Page 81
SECTION 7 – PLUMBING Antifreeze Siphon Tube Winterization Valve Water Heater Bypass Valve Antifreeze Siphon Tube and Winterization Valve • Model 24G - Located beneath galley sink • Model 24G - Located in water service center (remove front panel to access) (turn Winterization Valve 2 to “Winterize”...
Page 82
SECTION 7 – PLUMBING Fill Drainage System P-Traps NOTE: On Model 24G, turn the Winterization Valve 2 (located in the water service 16. Pour about one cup of RV antifreeze down center) to “Normal” position. each drain for the galley sink, lavatory sink, and shower/tub.
SECTION 7 – PLUMBING WATER SYSTEM DRAIN VALVE LOCATIONS Model System Drain Valve Locations 24G & 24V Waterlines • Two (2) valves located in water service center. Water Tank • One (1) valve located in water service center. Water Heater •...
SECTION 8 – ENTERTAINMENT To Swivel TV TV – 12V LED • Grasp the inboard side of TV and disengage -If Equipped from the wall mounting bracket. The LED flat panel TV is powered by 12-volt DC current. The 12-volt current is supplied from the house batteries, or from the power converter when connected to shoreline power or running the generator.
SECTION 8 – ENTERTAINMENT Set TV Video Input AUDIO-VIDEO SYSTEM BASIC • Turn TV and Radio/DVD player ON. OPERATION • Press the MODE button on the TV or the SOURCE button on the remote to select NOTE: For your convenience, we have also “INPUT 2”.
SECTION 8 – ENTERTAINMENT 3. Press the AUX input selection button (located just below the display on the face of the Radio/ DVD Player.) This will route the TV stereo sound output through the Radio/DVD Player and out to the Deluxe Sound speakers. 4.
SECTION 8 – ENTERTAINMENT 6. Rotate antenna to illuminate the last flickering LED light. 7. Repeat Steps 5 and 6 to pinpoint signal reception. NOTE: Refer to television manufacturer’s instructions to scan for available channels. Further Information See the antenna manufacturer’s user guide Digital Antenna Power Switch provided in your InfoCase for complete operating (Located in an overhead cabinet or...
A second connection may be included inside a cabinet in the bedroom for the rear TV (if equipped). ® See your authorized Winnebago Industries dealer for proper installation and sealing of roof mounted components. • HDMI Connection •...
SECTION 9 – FURNITURE AND SOFTGOODS SLEEPING FACILITIES WARNING Sleeping facilities are not intended for use while vehicle is in motion. For safety, passengers must use safety belted seating positions while vehicle is in motion. 3. Using the pull strap (attached to the back side COMFORT SOFA SLEEPER of the sofa), pull the sofa back out and extend –If Equipped...
Page 92
SECTION 9 – FURNITURE AND SOFTGOODS NOTE: The air mattress is plugged into an AC Silent Night Comfort Adjust power outlet behind the sofa. If your air bed pressure drops below the It may be necessary to press the “Reset” predetermined pressure level, the Silent Night button on the galley GFCI outlet before Comfort Adjust Pump will automatically turn on...
SECTION 9 – FURNITURE AND SOFTGOODS Further Information NOTE: Pump will automatically turn off and the Inflate/Deflate switch will automatically See the air bed manufacturer’s user guide return to the OFF position upon provided in your InfoCase for complete operating complete deflation.
SECTION 9 – FURNITURE AND SOFTGOODS 3. Place dinette table securely onto the dinette pedestal leg. 2. Flip seat back support upright. Reverse steps to store dinette table and pedestal leg. EXTENDABLE SECTIONAL – L-SHAPED DINETTE –If Equipped (Typical View – Your coach may differ in appearance) 3.
Page 95
SECTION 9 – FURNITURE AND SOFTGOODS Seat Back Cushion Storage Location 4. Turn seat cushion over and reinstall onto 6. Remove dinette table and pedestal leg from sectional frame, ensuring the four rear wardrobe cabinet. engagement pins (one located on each corner 7.
SECTION 9 – FURNITURE AND SOFTGOODS 9. Reverse steps to store dinette. NOTICE Stow furniture extension before retracting slide rooms. FLEX BED –If Equipped (Typical View – Your coach may differ in 2. Lay fitted cushion over the extended bed appearance) board.
No matter which species you choose for your -Typical View new Winnebago Industries motorhome cabinetry, please keep in mind that no two pieces Further Information of wood are exactly the same.
Page 98
SECTION 9 – FURNITURE AND SOFTGOODS Additionally, wood species exhibit other defining characteristics, such as mineral deposits/streaks, knots, sap runs, pin holes, and wormholes. These markings make the wood unique and contribute to its enduring beauty. Therefore, since wood is a product of nature and will have certain natural characteristics and variances, they are not covered under the warranty.
SECTION 10 – SLIDEOUT ROOMS Rear slideout switches (if equipped) are SLIDEOUT ROOM KEYLOCK typically located on a wall in the rear of the coach in or near the slideout room. Location varies by A Master Slideout Room Keylock is located model and floorplan.
Page 100
SECTION 10 – SLIDEOUT ROOMS To Retract Slideout Room WARNING Before Retracting! • Be sure the coach is level and the Parking Brake is set. CRUSH HAZARD. Keep people and • Ensure exterior compartment doors are closed objects clear of the inside and outside of the slideout room when operating.
SECTION 10 – SLIDEOUT ROOMS • Press the Slideout Room “RETRACT/IN” SLIDEOUT ROOM switch and hold until the room is fully TROUBLESHOOTING retracted, then release the switch. (LIPPERT) • To stop retracting the room during operation, release the button. -If Equipped •...
SECTION 10 – SLIDEOUT ROOMS • (8) - HALL SIGNAL NOT PRESENT. • Motor • Mode Encoder is not providing a signal. This is • Status Direction Button LED’s usually a wiring problem. • (9) - HALL POWER SHORT TO GROUND.
Page 103
SECTION 10 – SLIDEOUT ROOMS There are two slideout motors equipped on the end wall of each slideout room. Pull back wipe seal to access motors. NOTE: Use caution when removing components on painted units. Push-In Procedure 1. Using a razor blade, remove sealant from the top of screw cover.
SECTION 10 – SLIDEOUT ROOMS 7. When the slideout room is fully retracted, secure the room with a support item (e.g. 2x4 wood board) above the interior slideout room to secure room during travel. NOTE: For larger slideout rooms, place a travel support item on each end of the interior slideout room.
Page 105
SECTION 10 – SLIDEOUT ROOMS Slideout Room Seal Care and Maintenance While most household cleaners work well for cleaning slideout room seals, certain chemical agents may cause the seals to degrade. Typically, ® ® and Lysol type products work well. Use a ®...
• Have the sealant replaced if you notice any of attention. Delaying these repairs may allow water the above. Your local Winnebago Industries leakage and result in damage to interior ceiling dealer has the correct and necessary parts and and body panels, upholstery, etc., which is not experience to help you maintain your sealants.
SECTION 11 – MAINTENANCE AND STORAGE weight to the vehicle. This, in effect, reduces the • Do not scrape ice or snow from the painted amount of cargo you can carry and remain within surface. Brush off gently with a soft-bristled GVWR and GAWR limits.
Page 109
SECTION 11 – MAINTENANCE AND STORAGE Washing NOTE:Avoid aiming water flow from a hose or spray from high-pressure washing • Commercial vehicle wash facilities should be equipment into any appliance intake, as strictly avoided! They will scratch your RV! damage or difficulty in operating Truck-style wash centers have high- appliances may occur.
SECTION 11 – MAINTENANCE AND STORAGE Further Information • Avoid paste waxes. They sometimes have fillers and additives that give a very short term See the manufacturer’s information provided result. Stay away from silicones in polishes in your InfoCase for complete care and and soaps.
SECTION 11 – MAINTENANCE AND STORAGE EXTERIOR LIGHTS NOTICE ® Most Winnebago Industries vehicles have polycarbonate lenses on exterior lamps, which are very sensitive to a variety of chemical Do not use citrus-based cleaners on solvents and cleaners. polycarbonate finishes. Citric compounds...
SECTION 11 – MAINTENANCE AND STORAGE shades should be closed when the motorhome is parked for an extended UltraLeather Cleaning Chart period of time. Detergent/ Cleaner/ Type of Stain Water Degreaser Coffee, Tea WARNING Red Wine, Liquor Cola, Soft Drinks ...
SECTION 11 – MAINTENANCE AND STORAGE Scale Vinyl simulated wood panels may be cleaned with a mild, water-based cleaner and a soft cloth. To remove scale left by water, simply use a Do not use solvents on vinyl wood panels. multipurpose cream detergent and a soft cloth.
SECTION 11 – MAINTENANCE AND STORAGE • Do not use wool, abrasive brushes, or tools VINYL FLOORING that have previously cleaned other metals, because as well as scratching the surface, they Care and Maintenance can generate contamination and unattractive You can easily maintain the beauty of your stains.
SECTION 11 – MAINTENANCE AND STORAGE Treatment of Stains Tub and Shower Walls The tub and shower walls in the bathroom Acids, alkali, alcoholic beverages, coffee, soft should be cleaned with mild soap and warm drinks, ketchup, fruit, fruit juices, food, water.
SECTION 11 – MAINTENANCE AND STORAGE 5. Fully charge the batteries. Batteries must If you are storing your vehicle through the have at least 80% charge to survive winter, or in cold climates, extra preparations freezing temperatures and long period of must be made to protect equipment and systems non-use.
SECTION 11 – MAINTENANCE AND STORAGE 15. Replace batteries, if necessary, and check out electrical system to make sure all lights and electrical components operate. 16. Check tires for proper cold inflation pressure. See “Vehicle Certification Label” in Section 1 - Introduction.
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals. Always use specified sections or manufacturer’s guide for further information and instructions. Propane Gas System ...
Page 119
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals. Always use specified sections or manufacturer’s guide for further information and instructions. Safety Equipment Check operation of the following items: ...
Page 120
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals. Always use specified sections or manufacturer’s guide for further information and instructions. Sealants ...
SECTION 12 – MISCELLANEOUS NOTE: We recommend that you dump all LOADING THE VEHICLE holding tanks before traveling to avoid carrying unnecessary weight. NOTE: Your motorhome’s load capacity is designated by weight, not by volume, so you cannot necessarily use all available WARNING space when loading your motorhome.
Page 122
SECTION 12 – MISCELLANEOUS Corner Weighing (Side-to-Side) You will first drive only your front wheels onto the scale pad, then drive ahead so that the The most accurate method of weighing a whole vehicle is on the scale, then finally pull off motorhome is to weigh each “corner”...
SECTION 12 – MISCELLANEOUS axle is 12,000 lbs., then the load on each rear dual Because of individual vehicle use and loading set (left rear duals or right rear duals) should not habits, we recommend weighing the vehicle exceed 6,000 lbs. while fully loaded to avoid exceeding any of the listed Gross Weight Ratings.
SECTION 12 – MISCELLANEOUS Check state regulations on trailer weight and TRAILER WIRING trailer brake requirements to be sure you select CONNECTOR the right equipment before towing. Before descending a steep or long grade when Your coach is pre-wired for trailer or car towing a trailer, reduce speed and shift into a towing lights with a 7-pin socket.
(hinge side) of equipped with a Class 3 hitch may have a the screen door. label limiting vertical tongue load to 350 lbs. All Winnebago Industries models equipped with a Class IV hitch have a 12-5...
SECTION 12 – MISCELLANEOUS Automatic Mode - Entry Step This feature is intended to prevent injury or damage by an extended step while the vehicle is Switch ON moving. (Step Operates with Door) With the Step switch in the ON position, the Further Information step is in Automatic Mode.
SECTION 12 – MISCELLANEOUS POWER ROOF VENTILATOR Lounge, Galley, or Bath Area –If Equipped The vent dome is raised and lowered using the Dome Crank knob on the fan. The turbine fan will start automatically as the vent is raised, and stop as the vent is lowered. Manual Dome Fuse Fan Speed...
SECTION 12 – MISCELLANEOUS selector on the fan allows you to adjust the amount of circulation you need at any WARNING time. Do not exceed 225-lb. maximum weight capacity. 5. If you want the vent dome raised without the Misuse of ladder could result in death or serious injury. fan running, turn Off either the Fan Power See Operators Manual before using ladder.
SECTION 12 – MISCELLANEOUS ENTRANCE DOOR PROP ROD Power -If Equipped Awning Switch (Typical view – your coach may differ in • Press to appearance depending on model.) Retract The main entrance door may feature a rod (OUT). designed to prop the entrance door open when the patio awning arm is attached to the sidewall and •...
SECTION 12 – MISCELLANEOUS EFFECTS OF PROLONGED OCCUPANCY Your motorhome was designed primarily for recreational use and short-term occupancy. If you expect to occupy your coach for an extended period, be prepared to deal with condensation and humid conditions that may be encountered. Humidity and Condensation Moisture condensing on the inside of windows is a visible indication that there is too...
Page 131
INDEX About this Manual ..........................1-1 Air Conditioner Filter ........................... 4-10 Air Conditioner/Heater – Automotive (Dash) ..................3-3 Audio-Video System Basic Operation ....................8-2 Bathroom .............................. 11-9 Battery Access ............................6-8 Battery Boost Switch ..........................3-6 Battery Care ............................6-9 Cabinetry –...
Page 132
Index Exterior Graphic Care ........................... 11-4 Exterior Lights ............................11-5 Exterior Shower/Wash Station ........................ 7-7 Exterior Speakers ............................ 8-3 Fire Extinguisher ............................. 2-5 Flex Bed ..............................9-6 Formaldehyde Information ........................2-8 Fresh Water System ..........................7-1 Front Axle Tire Alignment ........................1-2 Fuel and Propane Gas ..........................
Page 133
Index Propane Vaporization in Cold Weather ....................5-5 Radio In-Dash/Rearview Monitor System ....................3-3 Range and Refrigerator ......................... 11-8 Range Hood ............................4-4 Range Top ............................... 4-3 Refrigerator ............................. 4-1 Refrigerator Service Access Compartment ..................... 4-2 Refrigerator Service Access Compartment ..................... 4-3 Remote Keyless Entry ..........................
Page 134
Index Valve Stem Access ..........................3-7 Vehicle Certification Label ........................1-4 Vehicle Storage – Preparation ......................11-9 Vehicle Storage – Removal ........................ 11-10 Vinyl Flooring ............................11-8 Waste Water System (Waste Pump) ....................... 7-7 Water Heater - Gas/ Electric ........................4-7 Water Heater Bypass and Antifreeze Siphon Valves ................
Need help?
Do you have a question about the Navion iQ and is the answer not in the manual?
Questions and answers