Storing, Copying, Midi Dump - The "Write" Menu - Quasimidi Technox Owner's Manual

13.) STORING, COPYING, MIDI-DUMP - THE „WRITE" MENU
THE WRITE-MENU
13.) The Write- In the following section you will learn everything about storing, copying and MIDI dumping of your
Menu sound creations and how the TECHNOX parameters are initialized.
There are two possible ways to archive your sounds: You can save the performances and multi-setups
either internally to the built-in RAM or you can send these via MIDI to an external MIDI recording device
such as a sequencer or MIDI data recorder. The advantage of using internal memories is that you have
direct access to all configurations without using an external MIDI device. But on the other hand it might
also be useful to archive a complete system setup externally together with your MIDI songfile. So it will
be assured that each song will be played back correctly, even if you have changed all internal RAM
configurations. Most sequencers handle the system-exclusive data (that's the data format used for external
storage...) exactly like any other MIDI data; so the easiest way is to record the „TECHNOX configuration
block" straight into your sequencer and put this block in front of the song.
The „Write-Menu" will be activated as follows:
Function
Selection of edit level
Selection of „Write" menu
Confirm selection
The „Write-Menu" offers you the following sub-menus:
|1>
<2>
<3>
<4>
<5>
<6>
26
Depending upon which mode your TECHNOX currently uses (Performance or
|1>\Write\Perf.?
Sequencer-Multi-Mode), the displayed message of this sub-menu differs. Refer to
Yes<Ok>\No<EXIT>
sections about Performance-editing and sequencer setups for complete
descriptions.
|1>\Write\Setup?
Yes<Ok>\No<EXIT>
Here you can restore a sequencer-multi-setup that has been created before. After
<2>\Load\Setup?
pressing the „EDIT/OK" key a menu will be displayed where you can select the
Yes<OK>\No<EXIT>
selected setup by using the „VALUE/SOUND" dial. But it's easier to do the setup
recall by letting the TECHNOX receive a program change information via MIDI.
This function will be enabled by selecting „[RxSetupC: On]" in page <7> of the
„Edit System" menu. Program changes between 1 and 14 select one of the 14
possible setups.
This sub-menu allows you to store your User-drum-set. Refer to section
<3>\Write\Drums?
„Drumset-Editing" for complete instructions.
Yes<OK>\No<EXIT>
Use this function to initialize the actual sequencer-setup. After initializing, all parts
<4>\Init\Setup?
of the setup are set to Single-sound #1, FX-1 is set to „Room" and FX-2 to
Yes<OK>\No<EXIT>
„Chorus".
The „VALUE/SOUND" Alpha-dial is used to select the part which has to be
<5>\Init\Part\1?
initialized. After completing this functions, all part-parameters of this part are
Yes<OK>\No<EXIT>
re-set to their default values.
By using the „VALUE/SOUND" dial it's possible to select a part which has to be
<6>\Copy\Part\1?
copied to another part. Use the „EDIT/OK" key to confirm your selection. and
Yes<OK>\No<EXIT>
then the „VALUE/SOUND" dial to select the copy target. After pressing
„EDIT/OK" all part parameters from the destination will be copied to the target.
User action
(Keys/Dials)
Press „EDIT/OK" key.
Use one of the two Alpha-dials to
select.
Press „EDIT/OK" key.
Display-Message
\Edit/Function
\Edit/Function
<8>\Write/Dump..
|1>\Write\Setup
Yes<OK>\No<EXIT>
QUASIMIDI STYLEDRIVE FANSEITE
http://people.freenet.de/styledrive/