Quasimidi Technox Owner's Manual page 18

8.) Editing the effects
Equalizer
The equalizer is an effective tool for sound enhancement, because you can change the sound spectrum for different
frequenzies individually.
|1>
<2>
The equalizer algorithms of the technox offer graphical EQ´s. With this kind of EQ´s you can adjust different frequency
bands of the audio signal. The first equalizer offers the frequencies of 100 Hz, 500 Hz and 3kHz. The second equalizer
offers the frequencies of 70 Hz, 300 Hz and 3kHz. To hear only the post EQ-Signal of an instrument, you have to switch
the pan-position of the selected part to "---".
<3>
<4>
<5>
<6|
Wah-Wah-Effect
Although the Wah-Wah effect had a strong influence on contemporary music for a couple of years, it is seldomly used
nowadays. It combines a resonant sweepable filter with overdrive.
|1>
<2>
<3>
<4>
<5>
<6>
Auto-Wah-Wah
Similar to the preceding effect, but the cutoff frequency can not be adjusted manually. It is controlled through the input
level, in other words: from the sound's volume envelope. Mainly percussive sounds should be used with it, therefore. The
parameters are the same as in WahWah+Overdrive. Only Freq is not available.
|1>
Distortion/
These effects produce distortion and overdrive. Distortion has an additional gain switch for hard&heavy sounds.
Overdrive
|1>
<2>
<3>
<4|
18
The Effects No. 15 and 16 are two different Equalizers.
Edit\FX2\Typ
|1>\15:Equalizer
This Parameter controls the Input-Level of the Effect-Processor.
Edit\FX2\Paramtr
<2>\InputLev:\64
Rises or lowers the spectrum of the first frequency.
Edit\FX2\Paramtr
<3>\100\Hz:\\\+0
Rises or lowers the spectrum of the second frequency.
Edit\FX2\Paramtr
<4>\500\Hz:\\\+0
Rises or lowers the frequency of the third frequency
Edit\FX2\Paramtr
<5>\3000\Hz:\\+0
Output level of the effect.
Edit\FX2\Paramtr
<6|\OutputLv:127
Effect No. 17 is a Wah-Wah-Effect combined with Overdrive
Edit\FX2\Typ
|1>\17:WahWah+Ov
This Parameter controls the Input-Level of the Effect-Processor. The strength of
Edit\FX2\Paramtr
the overdrive parameter is also influenced by these input-level.
<2>\InputLev:\80
Controls the Cutoff frequency of the filter. This is most useful for MIDI control of
Edit\FX2\Paramtr
the effect.
<3>\Freqncy:\\64
Adjusts the Overdrive effect.
Edit\FX2\Paramtr
<4>\Drive:\\\100
Sets the clip-level for the overdrive.
Edit\FX2\Paramtr
<5>\ClipLev:\100
Adjusts the overall level. It is recommended to use relatively high input level and
Edit\FX2\Paramtr
low output level, in order to make the overdrive respond properly.
<6|\OutputLv:127
Effect No.18 offers a wahwah-Effect.
Edit\FX2\Typ
|1>\18:AutoWahWa
The Effects 19 and 20 offer Distortion-Algorithms.
Edit\FX2\Typ
|1>\20:Distortn
As nearly everybody knows, the input level/gain of an overdrive adjusts the
Edit\FX2\Paramtr
amount of distortion effect.
<2>\InputLev:\64\
This parameter (only available for distortion) sets the pre-gain.
Edit\FX2\Paramtr
<3>\Drive:\\\\\4
For adjusting the volume in comparison to "dry" sounds, you should adjust this
Edit\FX2\Paramtr
parameter.
<4|\OutputLv:\64
QUASIMIDI STYLEDRIVE FANSEITE
http://people.freenet.de/styledrive/