Quasimidi Technox Owner's Manual page 11

7.) Editing of the single-sounds
<10>
<11>
The following three parameters change the sound in time and are called envelope parameters. Percussive sounds have
short time periods, strings and pads have longer time periods. To change a time period like the attack-time to shorter
values you have to decrease the time to negative values based on the default value.
<12>
<13>
<14>
<15>
<16>
<17>
Because in the modulation matrix itself only the destination-parameter can be selected and not the part, you can choose in
the following menus the modulation intensity for each part. For further information have a look at chapter 11,
"Common-menu", where the modulation-matrix is described.
<18>
<19>
<20>
<21>
<22>
<23>
<24|
This parameter controls the cutoff-frequency of the lowpass filter. Above this
Part\13\_303Lead
point higher harmonics are cut off and below this frequency the harmonics can
<10>\CutFreq:\+0
pass. Real-time changes of this parameter should be done with a MIDI-controller
like the MOD-wheel of your keyboard because it is easier to handle than an alpha
dial. At TECHNOX the MOD-wheel is routed through the modulation matrix to
the tone-parameter by default. This controls the cut-off frequency directly.
This parameter controls the resonance of the filter, which means that the output of
Part\13\_303Lead
the filter is fed back to the input of the filter. At high values the filter can reach
<11>\Resonan:\+0
self-oscillation.
The rising-time of the envelope can be changed by this parameter.
Part\13\_303Lead
<12>\EG\Att:\\+0
This parameter is responsible for the speed how fast the level goes down from
Part\13\_303Lead
maximum amplitude to sustain-level.
<13>\EG\Dec:\\+0
This parameter controls the release time of the sound after lifting the fingers from
Part\13\_303Lead
the keys.
<14>\EG\Rel:\\+0
The intensity of the vibrato (frequency modulation)
Part\13\_303Lead
<15>\VibDpth:\+0
The speed of the Vibrato (frequency)
Part\13\_303Lead
<16>\VibRate:\+0
Here the delay time between pressing a key and beginning of the vibrato can be
Part\13\_303Lead
selected.
<17>\VibDely:\+0
This parameter controls how strong the LFO of the selected part will be modulated
Part\13\_303Lead
through the modulation matrix.
<18>\LfoMod:\\76
The amount of volume-changes for this part through the modulation-matrix can
Part\13\_303Lead
be regulated with this parameter. The values can be negative or positive, so that
<19>\VolMod:\+63
sound blending through MIDI-controllers etc. between various parts are possible.
The amount of pitch-changes for this part by the modulation-matrix.
Part\13\_303Lead
<20>\PtchSns:\+2
Also the amount of filter-modulation can be controlled for each part individually.
Part\13\_303Lead
Most of the factory sounds are programmed with an almost open filter. So it makes
<21>\ToneMod:+63
sense to choose a negative value for closing the filter with any modulation source.
Gliding in tune between two notes that are played after each other is called
Part\13\_303Lead
portamento. The tuning of the first note changes to the tuning of the next pressed
<22>\PorTime:\\0
note. The speed of this effect is controlled by this parameter.
Here you can enable the MIDI hold-pedal function. When disabled, a pressed
Part\13\_303Lead
hold-pedal of your connected keyboard causes no hold function on this part.
<23>\HoldPed:OFF
With this parameter you may select a special velocity-curve for each part separate.
Part\13\_303Lead
In the layer-performances with different curves on each used part it´s possible to
<24|\VelCv:\Fix
create cross-fades between sounds by using negative and positive curves for the
velocity.
11
QUASIMIDI STYLEDRIVE FANSEITE
http://people.freenet.de/styledrive/