Related Manuals for SportsArt Fitness S916
Summary of Contents for SportsArt Fitness S916
- Page 1 S916 Independnet Lateral Pull Owner’s Manual Sports Art Industrial Co., Ltd. TUV-CERT ISO 9001/9002/14000 Certified Quality Products 2013.07.23...
-
Page 2: Table Of Contents
S916 OWNER’S MANUAL CONTENTS 1. INTRODUCTION ................2 2. SAFETY PRECAUTIONS ..............3. LIST OF PARTS ................. 4. ASSEMBLE THE PRODUCT ............. STEP 1 Install the Rear Covers ............. STEP 2 Install the Seat Cushion ............STEP 3 Install the Foot Covers .............. -
Page 3: Introduction
1. INTRODUCTION Congratulations on the purchase of a high quality SportsArt product, the S916 Independent Lateral Pull machine. Constructed of high quality materials and designed for years of reliable performance, this product was made for full commercial use. Before this product is assembled or operated, we recommend that you familiarize yourself with this manual. -
Page 4: Safety Precautions
2. SAFETY PRECAUTIONS This product was designed and built for optimum safety. However certain precautions apply during the use of this product. Please note the following safety precautions: • Please read the entire manual before assembly and operation. Make sure the product is installed and operated as instructed in this manual. •... -
Page 5: List Of Parts
3. LIST OF PARTS Assembly Parts Name Qty. No. Name Qty. Main Frame A3 118 Oval Foot Cover A A1a Rear Cover, Top A4 118 Oval Foot Cover B A1b Rear Cover, Bottom A5 Storage Tray Seat Cushion... - Page 6 Components in the Hardware Kit Name Qty. Specification Notes Push revits L-shaped Allen wrench L-shaped Allen wrench Double open-end wrench 8*17 Double open-end wrench 13.2*15.2 Double open-end wrench 17*23 Components on the Product Name Specification Notes Flat head hex screws M8*P1.25*L20 Nylon hex nut Mushroom head inner hex screws M8*P1.25*L25...
-
Page 7: Assemble The Product
4. ASSEMBLE THE PRODUCT Follow instructions below to assemble this product. Note that in this manual the words “left” and “right” are used to refer to the product and its parts. As such, these designations correspond to the “left” and “right” sides of a person in position to exercise on this product. -
Page 8: Step 2 Install The Seat Cushion
STEP 2 Install the Seat Cushion (a). Remove screws (20) from the main frame (A1), then remove screws (21) from the seat cushion (A2). (b). Attach the seat plate onto the main frame (A1), then use screws (20) to secure the assembly. (c). -
Page 9: Step 3 Install The Foot Covers
STEP 3 Install the Foot Covers (a). Attach both foot covers (A3)(A4) onto the main frame legs. Connect both covers first, rotate the covers to expose the inside screw hole. Then use one push revit (10) to secure one side. Rotate the covers back to original position and use the other push revit (10) to secure the assembly. -
Page 10: Step 4 Install The Storage Tray Holder
STEP 4 Install the Storage Tray Holder Please follow the instructions (a) through (b) to install the storage tray (a). Locate the position where the storage tray (A5) attaches to the main frame (A1), then remove the screws (22) from the weight stack frame. (b). -
Page 11: Step 5 Seat Adjustment Instructions
STEP 5 Seat Adjustment Instructions * When adjusting the seat height, pull the seat lever to adjust to the desired height and then release the seat lever. * If the machine has not been used for a long time or the seat is adjusting slowly. -
Page 12: Step 6 Belt Tension Adjustment Instructions
STEP 6 Belt Tension Adjustment Instructions 1. After the installation and the final positioning of the machine, make the appropriate adjustments to ensure that the machine is working. 2. If the belt is too tight or too loose, first loosen nut A as shown then adjust nut B. -
Page 13: Maintenance
5. MAINTENANCE This section covers maintenance topics and includes a maintenance schedule, task list, and log. MAINTENANCE Machine Maintenance 1. Please clean and lubricate the guide rod once a week. (a). Use a clean, lint-free towel to apply the lubricant onto the guide rods. (b). -
Page 14: Machine Maintenance
MAINTENANCE Machine Maintenance IMPORTANT NOTE 1. Once the machine belt reaches the warranty period, it is recommended to replace the belt. 2. Belt safety check, after a year in use, check belt weekly. Depend on the use conditions, increase the frequency of inspections. (As shown: (A) a belt, (B) the belt extension) During inspection, if found cracks in the belt or the belt is exposed to other unusual circumstances, please immediately stop using the machine and... -
Page 15: Maintenance Schedule
MAINTENANCE Schedule Area Week Month Quarter Year Notes Exterior Clean. Screws Inspect for looseness and secure if necessary. Testing To confirm that the machine is working properly Cushions Wipe with a damp cloth. Belt Check for damage or wear. If so, need for replacement. -
Page 16: Maintenance Task List
MAINTENANCE Task List Like cars, fitness products require maintenance. Regular maintenance ex- tends product life, and failure to maintain products can void the manufac- turer’s warranty. Copy the maintenance log sheet, and record maintenance work for each fitness product. Daily tasks 1. -
Page 17: Maintenance One-Year Maintenance Log
MAINTENANCE One-Year Maintenance Log Facility:_______________________ Supervisor:____________________ Product model number:__________ Serial number:_________________ Start date: ____________________ End date:_____________________ Daily Tasks Weeks 1-7 Weeks 8-14 Weeks 15-21 Week 22-28 Completed Daily Tasks Week 29-35 Week 36-42 Week 43-49 Week 50-52 Completed Weekly Tasks Weeks 1-7 Weeks 8-14 Weeks 15-21 Weeks 22-28... -
Page 18: Consignes De Sécurité Importantes
6. CONSIGNES DE SÉCURITÉ IMPORTANTES Le produit SportsArt a été conçu et fabriqué afin d’assurer une sécurité optimale. Cependant certaines précautions s’appliquent chaque fois que vous utilisez votre produit. • Lisez entièrement le manuel avant l’assemblage et l’utilisation. Veuillez aussi noter les consignes de sécurité...
Need help?
Do you have a question about the S916 and is the answer not in the manual?
Questions and answers