Related Manuals for SportsArt Fitness ICARE E872MU
Summary of Contents for SportsArt Fitness ICARE E872MU
- Page 1 ICARE E872MU Body Weight Support System’s Manual Sports Art Industrial Co., Ltd. TUV-CERT ISO 9001/9002 Certified Quality Products 2012.11.28...
-
Page 2: Table Of Contents
ICARE E872MU OWNER’S MANUAL CONTENTS 1. INTRODUCTION ................2. SAFETY PRECAUTIONS ..............3. ASSEMBLE THE PRODUCT ............STEP 1 Install the Boom Assembly ............. STEP 2 Install the Leg Frame ............. STEP 3 Install the Hand Rail ............... STEP 4 Attach the Body Weight Support System to the E872MA .. -
Page 3: Introduction
1. INTRODUCTION Congratulations on your purchase of the SportsArt ICARE E872MU Body Weight Support System. Made through a partnership between Madonna ICARE and SportsArt Fitness, this product was built specifically for physical rehabilitation. Before this product is assembled or operated, we recommend that you familiarize yourself with this manual. -
Page 4: Safety Precautions
2. SAfETy PRECAUTIONS Safety was an important consideration in the design of the SportsArt Fitness ICARE E872MU Body Weight Support System. However, during the use of the physical rehabilitation elliptical trainer and the Body Weight Support System, you must pay careful attention to safety. - Page 5 2. SAfETy PRECAUTIONS (CONTINUED) ● Check all cables and harnesses before each use. Should you find any signs of wear or defect in the cable or pulley assembly, immediately call SportsArt service for repairs or service. Should you find any signs of defect in the harness, contact the harness manufacturer.
-
Page 6: Assemble The Product
3. ASSEMBLE THE PRODUCT STEP 1 Install the Boom Assembly (a) Remove mast assembly and boom assembly from packaging. Use care while handeling the assembly; these sections are connected by a cable. (b) Lay mast assembly on ground. Slide boom assembly down onto mast tube, align bolt holes. -
Page 7: Step 2 Install The Leg Frame
STEP 2 Install the Leg frame (a) Unpack both legs, slide legs into frame. (b) Connect air lines. Firmly press loose end of hose into fitting with matching hose. (c) Carefully tip unit upright. FRAME LEG... -
Page 8: Step 3 Install The Hand Rail
STEP 3 Install the Hand Rail (a) Insert carriage bolts through lowest hole on each side of the mast assembly. Add washer on opposite side and finger tighten nut. (b) Slide hand rail into frame. HAND RAIL 5/16-18 x 2.75" Carriage Bolt IC1049 IC1040... -
Page 9: Step 4 Attach The Body Weight Support System To The E872Ma
STEP 4 Attach Body Weight Support System to E872MA (a) Remove elliptical base cap on each side, lift up to remove. (b) Carefully slide Body Weight Support System forward over E872MA elliptical. Line up Body Weight Support System hole with threaded boss on E872MA elliptical. - Page 10 STEP 4 Attach Body Weight Support System to E872MA (d) Slide overturn strap under E872MA elliptical and on top of the Body Weight Support System legs. Two people will need to lift the front of the elliptical while the third slides the overturn strap into place. OVERTURN STRAP (e) Insert hardware as shown, tighten.
-
Page 11: Step 5 Install The Compressor And Connections
STEP 5 Install the Compressor and Connections (a) Unpack compressor and read instructions. Place compressor in front of machine. Locate provided black airline. Plug one end of the airline into compressor, and other end into the fitting found on front of Body Weight Support System leg. -
Page 12: Operate The Product
4. OPERATE THE PRODUCT Before activating the Body Weight Support System, use the adjustment knob to set the lift to an appropriate weight. It is better to start at a low lifting force and increase after activated. OPERATION Lift force Gauge Outer display indicates lifting force, in pounds. -
Page 13: Operation Activation Switch And Seat Adjustment Switch
OPERATION Activation Switch When in the “off” position the lifting cable can be lowered with minimal resistance, the cable will not retract up. When turned to the “on” position the cable will begin to retract. It will pull up with a force that correlates to the lift force gauge. OPERATION Seat Adjustment Switch Used to raise or lower the seat. -
Page 14: Maintenance
5. MAINTENANCE Body Weight Support System Electrical and Pneumatic Diagram BLOCK Part Number IC1016 IC1012 CONTROL BOX IC1014 IC1015 IC1055 ROCKER SWITCH 2.5 AMP FUSE 5mm x 20mm IC1017 3x - IC1061 4 CONDUCTOR, 18 AWG SPADE TERMINAL 4x - Ø5/8" GROMMET SHIELDED IC1057 IC1021... -
Page 15: Maintenance Schedule
Maintenance Schedule Parts Week Month 1/2year Notes Lift cable Inspect for detarioration. Actuator cord Inspect for damage or wear. Carabiner Insure the carabiner function properly and closed fully. Safety strap Inspect for wear and fraying. Pulley Ensure pulleys are free spinning. Cable system Inspect the lift cable for wear (fraying, cuts, or shaving). -
Page 16: List Of Parts
6. LIST Of PARTS PART# DESCRIPTION QTY. IC01-009 Cable Retainer IC01-010 Plastic Pin Spacer, Style 3 IC01-013 Hand Rail IC01-017 Overturn Strap IC01-019 Plastic Pin Spacer, Style 1 IC01-021 Seat Transition Plate IC01-023 Boom Shear Pin IC01-024 Cylinder Clevis Pin IC01-025 Pulley Clevis Pin, Long IC01-026... - Page 17 6. LIST Of PARTS (CONTINUED) IC1032 Air Fitting, Bulkhead Ø1/4 IC1036 Ø3/8 Air Line x 8ft, Black IC1038 Seat Swivel IC1039 M6-1 x 10mm BHCS, Zinc IC1040 5/16-18 x 2.75” Carriage Bolt, Zinc IC1041 5/16-18 x 2” FHCS, Zinc IC1042 1/4-20 x 5/8”...
-
Page 18: List Of Parts Diagram
7. LIST Of PARTS DIAGRAM IC01-009 IC01-025 IC01-030 IC01-010 IC1008 IC1058 IC01-009 IC1007 IC1059 IC01-026 IC01-023 IC01-019 IC1046 IC1048 IC1007-02 IC1069 IC1058 IC1047 IC01-207 IC1074 IC1052 IC01-204 IC1069 IC1059 IC1072 IC1004-02 IC1068 IC1071 IC1004 IC1069 IC01-203 IC01-203 IC01-206 IC1065 IC1045 IC1076 IC1057 IC01-033...
Need help?
Do you have a question about the ICARE E872MU and is the answer not in the manual?
Questions and answers