Ease of mind The MDSC-2242 comes with a smart cable management system. The design allows easy mounting on arms/suspension system. Available in two models, this surgical display also features a host of connectivity options and remote control.
About this user guide Overview This manual provides a support to the user during the installation, set up and utilization of the MDSC-2242 display. Depending on the specific version that has been purchased, some of the features and options described in this document may not apply to the display in user’s hands.
Multi-image selection key / Down key Image zoom key / Up key OSD Menu key / Enter key Brightness decrease / Left key Brightness increase / Right key Stand-by key A 7-key keypad is located on the right side of the display. (451920611333)K5903030 MDSC-2242 09/10/2014...
Left Down Right Ok (Select) Input Selection Brightness + Back PiP Swap Brightness - Connector view 2.4.1 MDSC-2242 LED version Overview Image 2-4 Mains input Earth SDI-1 out SDI-1 in DVI out DVI-1 in Display Port in Sync/Cr in CVBS/Y in...
2. Parts, controls and connectors 2.4.2 MDSC-2242 MNA version Overview Image 2-5 Mains Input Earth Optical 10Gb Ethernet SFP+ interface* LED2* Orange blinking: Activity = (Tx) or (Rx) Off: No network activity LED1* Green: Link is active Off: No active network connection...
PC analog (VGA) input source can be connected to the DVI-I input connector using a DVI-I to VGA adapter. The use of an adapter cable of at least 0.15 m long will allow an easy placement inside the cable cover. (451920611333)K5903030 MDSC-2242 09/10/2014...
VESA arm/suspension interface with a thickness of up to 4 mm. If, due to the thickness of the external VESA arm interface (=V), the length of the provided screws (=L) is not suitable, consider the following rule: = V + 8mm = V + 15mm (451920611333)K5903030 MDSC-2242 09/10/2014...
PiP and SbS features on your MDSC-2242. This chapter describes how to connect the different video input types for each version of the MDSC-2242. 3.2.1...
About video output connections Beside the video input connections, the MDSC-2242 also has video output capabilities allowing you to loop-through certain video inputs connected with the MDSC-2242 to another display, projector, video recorder, ...
This chapter describes how to make use of the video output connections available for each version of the MDSC-2242. 3.3.1 MDSC-2242 LED version To connect the video outputs 1. Connect one or more of the available video sink(s) to the corresponding video outputs using the appro- priate video cable(s).
To connect your MDSC-2242 to Barco’s Nexxis OR system, connect the 10Gb Ethernet interface to your Nexxis switch. More info about Nexxis OR and how to configure the MDSC-2242 in your network is avail- able in the dedicated user guides. Please visit www.barco.com...
As a result, the OSD main menu comes up in the bottom right corner of the screen. If no further actions are taken within the following 30 seconds, the OSD menu will disappear again. The time-out of the OSD menu automatic close function can be adjusted or disabled in the OSD menu (OSD Time-out). (451920611333)K5903030 MDSC-2242 09/10/2014...
If the selected menu item is a multiple choices menu use the keys to select the desired option then press the key to confirm. • Press again key to select other Menu items or exit from the Menu page by pressing the key. (451920611333)K5903030 MDSC-2242 09/10/2014...
- Large PiP: 50% of Primary height in top-right corner - Side-by-Side: Primary and Secondary input of equal height Only a subset of multi-image configuration settings is available via this shortkey func- tion. More multi-image configuration settings can be selected in the OSD menus. (451920611333)K5903030 MDSC-2242 09/10/2014...
The Barco remote control operates on an infrared (IR)-based transmitter. If it has an unobstructed line-of- sight to the receiver, the Barco remote control can function at distances of up to 30 feet (about 9 meters). The remote control duplicates the functions of the keyboard.
Page 25
Battery replacement should be done as depicted on the back side of the remote control. Use a Lithium Battery CR2032 3V type. AUTION Replace with the correct battery type, there is risk of explosion if the battery is replaced with an incorrect type. (451920611333)K5903030 MDSC-2242 09/10/2014...
To adjust the brightness level 1. Bring up the OSD main menu. 2. Navigate to the Picture menu. 3. Enter the Brightness submenu. The command bar Brightness is highlighted. 4. Set the brightness level as desired and confirm. (451920611333)K5903030 MDSC-2242 09/10/2014...
• User Factory calibration – White point: The White Color points associated with the Color Temperature: 5600K, 6500K, 7600K or 9300K are factory calibrated with a consequent reduction of the maximum luminance compared to Native Color Temperature. (451920611333)K5903030 MDSC-2242 09/10/2014...
To adjust the sharpness level 1. Bring up the OSD main menu. 2. Navigate to the Picture menu. 3. Enter the Sharpness submenu. The command bar Sharpness is highlighted. 4. Set the sharpness level as desired and confirm. (451920611333)K5903030 MDSC-2242 09/10/2014...
4. Select one of the available Smart Video presets and confirm. 5.2.3 Image Position This menu item is only available when VGA input is connected. To adjust the image position 1. Bring up the OSD main menu. 2. Navigate to the Picture advanced menu. (451920611333)K5903030 MDSC-2242 09/10/2014...
5.2.6 Clock/Line This menu item is only available when VGA input is connected. About clock/line If the result of the Auto Adjustment procedure described above isn’t satisfactory, the Clock/Line can be manually adjusted by following this procedure. (451920611333)K5903030 MDSC-2242 09/10/2014...
Available main sources dependent on display model. The main source can also be selected through a shortkey function. To select the main source 1. Bring up the OSD main menu. 2. Navigate to the Display Format menu. 3. Enter the Main Source submenu. (451920611333)K5903030 MDSC-2242 09/10/2014...
The available image sizes for your display are: • Full Screen (fill the screen, image aspect-ratio can be altered) • Aspect (fill the screen on largest dimension, no modification in image aspect-ratio) • Native (input pixel to LCD pixel mapping, no scaling) (451920611333)K5903030 MDSC-2242 09/10/2014...
Picture Source About 2 picture sources The available 2 picture sources for your display are: • Auto Search • Composite • S-Video • Component • PC Analog • DVI 1 • SDI 1 • Nexxis • DisplayPort (451920611333)K5903030 MDSC-2242 09/10/2014...
To swap pictures means to exchange (swap) main and 2 picture. To swap pictures 1. Bring up the OSD main menu. 2. Navigate to the Display Format menu. 3. Enter the Picture Swap submenu. 4. Select the desired setting and confirm. (451920611333)K5903030 MDSC-2242 09/10/2014...
• Deutsch • Español • Italiano To select the language 1. Bring up the OSD main menu. 2. Navigate to the Configuration menu. 3. Enter the Language submenu. 4. Select one of the available languages and confirm. (451920611333)K5903030 MDSC-2242 09/10/2014...
5. Set the OSD horizontal position as desired and confirm. 5.4.4.2 OSD Vertical Position To adjust the OSD vertical position 1. Bring up the OSD main menu. 2. Navigate to the Configuration menu. 3. Enter the OSD setting submenu. (451920611333)K5903030 MDSC-2242 09/10/2014...
User 1, User 2 or User 3 profile. The Factory and X Ray profiles can be modified, but the factory default can’t be overwritten and can always be recalled through the recall profile menu item. The available profiles to save in your display are: (451920611333)K5903030 MDSC-2242 09/10/2014...
This setting allows you to select which digital input to replicate on DVI out. The available options are (depending on display version): • DVI 1 • Nexxis This feature is subject to restrictions in case of Multi-image (PiP, SbS). (451920611333)K5903030 MDSC-2242 09/10/2014...
2. By activating the OSD menu, see "OSD menu activation", page 19. To enable/disable power saving 1. Bring up the OSD main menu. 2. Navigate to the System menu. 3. Enter the Power Saving submenu. 4. Enable/Disable power saving as desired and confirm. (451920611333)K5903030 MDSC-2242 09/10/2014...
This equipment must be earthed. • Power requirements: The equipment must be powered by the AC mains voltage. • The equipment should be installed near an easily accessible outlet. • The equipment is intended for continuous operation. (451920611333)K5903030 MDSC-2242 09/10/2014...
Page 42
Sufficient expertise is required for installing this equipment, especially to determine the strength of the wall for withstanding the display’s weight. Be sure to entrust the attachment of this equipment to the wall to licensed contractors of Barco and pay adequate attention to safety during the installation and usage.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee (451920611333)K5903030 MDSC-2242 09/10/2014...
Page 44
(Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section "Limit Requirements of toxic substances in Electronic Information Products".
“Electronic Information Products Pollution Control Labeling Standard” of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “Standard of Electronic Information Products Environmental Friendly Use Period”...
Take care not to scratch the front surface with any hard or abrasive material. • Dust, finger marks, grease etc. can be removed with a soft damp cloth (a small amount of mild deter- gent can be used on the damp cloth). • Wipe off water drop immediately. (451920611333)K5903030 MDSC-2242 09/10/2014...
Indicates the device is approved according to the KC regulations Indicates the device is approved according to the BSMI regulations Indicates the USB connectors on the device Indicates the DisplayPort connectors on the device Indicates the manufacturing date (451920611333)K5903030 MDSC-2242 09/10/2014...
Page 48
Indicates that the box should be carried with two persons. 20 - 30 Kg Indicates that the box should not be cut with a knife, a cutter or any other sharp object. 1. Values for xx and yy can be found in the technical specifications paragraph. (451920611333)K5903030 MDSC-2242 09/10/2014...
Barco software products are the property of Barco. They are distributed under copyright by Barco N.V. or Barco, Inc., for use only under the specific terms of a software license agreement between Barco N.V. or Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any form, is authorized.
Page 50
DVI-I Single Link (digital & analog – HDMI video support with HDCP) version) DisplayPort (VESA std 1.1a) S-video (4-pin Mini DIN) Composite video (1x BNC) Component video RGBS / YPbPr (4x BNC) Barco NEXXIS network adapter integrated Video output signals (MNA DVI-D version) Composite video (1x BNC) S-video (4-pin Mini DIN)
Total Total (Ypb) YPbPr 1080p59 1920 x 1080 1080p 67,433 59,94 1080p60 1920 x 1080 1080p 67,5 Dimensions Handles excluded 41.1 1015.5 Handles Image 6-2 Open source license information Open source license information Open source license usage (451920611333)K5903030 MDSC-2242 09/10/2014...
Page 55
6. Important information This product contains software components released under an Open Source license. A copy of the source code is available on request by contacting your Barco customer support representative. EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA- TION ARE PROVIDED "AS IS"...