Subscribe to Our Youtube Channel
Related Manuals for Advantech AIMB-502
Summary of Contents for Advantech AIMB-502
- Page 1 User Manual AIMB-502 Intel® Xeon® E3/Core™ i7/i5/i3 LGA1155 MicroATX with CRT/ DVI/HDMI, 6 COM, Dual LAN, DDR3, PCIe x 16, USB 3.0 and SATAIII...
- Page 2 The documentation and the software included with this product are copyrighted 2013 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice.
-
Page 3: Declaration Of Conformity
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer's instructions. AIMB-502 User Manual... - Page 4 2.5 GHz Intel® Pentium® Processor G850 SR05Q 5 GT/s 32nm LGA1156 PASS 2.90 GHz Intel® Core™ i3- 2120T Processor Q1FR 5 GT/s LGA1156 PASS 2.6 GHz Intel® Pentium® Processor G630T Q1CT 5 GT/s LGA1156 PASS 2.3 GHz AIMB-502 User Manual...
- Page 5 SEC K4B4G0846B DDR3 N XQ16B8N8GS-9-AV 1600 (512x8) DDR3 Micron 2FD27 D9PCP Apacer DDR3 N 78.C1GET.ATF0C 1600 (512x8) DDR3 SEC 113 HCK0 DDR3 N D3US56081XH12AA 1600 K4B2G0846C 256x8 DDR3 SEC 113 HCK0 DDR3 N D3US56082XH12AA 1600 K4B2G0846C 256x8 AIMB-502 User Manual...
-
Page 6: Ordering Information
1 x 1 PCIe 8 x 2 AIMB- ECC/ (PCI 502WG C216 Non- 2 / 4 1 2 / 2 1 / 1 e 16 slot) 00A1E PCIe 1 x 1 *() means do not populated on MP version. AIMB-502 User Manual... - Page 7 It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the AIMB-502, check it for signs of ship- ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately.
- Page 8 AIMB-502 User Manual viii...
-
Page 9: Table Of Contents
Board layout: Jumper and Connector Locations ........5 Figure 1.1 Jumper and Connector Location ........ 5 Figure 1.2 I/O Connectors ............5 AIMB-502 Board Diagram ................. 6 Figure 1.3 AIMB-502 Block Diagram ........... 6 Safety Precautions ..................7 Jumper Settings ..................7 1.8.1 How to Set Jumpers.............. - Page 10 Software API................58 4.2.2 Software Utility................59 Chapter Chipset Software Installation Utility Before You Begin..................62 Introduction ..................... 62 Windows XP/Windows 7 Driver Setup ............ 63 Chapter VGA Setup ......... 65 Introduction ..................... 66 Windows 7/XP..................66 AIMB-502 User Manual...
- Page 11 Table B.17:Power LED (JFP3)............ 89 B.18 IrDA connector (JIR1) ................90 Table B.18:IrDA connector (JIR1)..........90 B.19 Case Open sensor (JCASE1) ..............90 Table B.19:Case Open sensor (JCASE1)........90 B.20 Case Open Mode Connector (JCASEOP_SW1) ........90 AIMB-502 User Manual...
- Page 12 Table B.20:Case Open Mode Connector (JCASEOP_SW1)..90 B.21 RS-485 terminator jumper setting (J485P) ..........91 Table B.21:RS-485 terminator jumper setting (J485P/N) ... 91 AIMB-502 User Manual...
-
Page 13: Chapter 1 General Information
Chapter General Information... -
Page 14: Introduction
Introduction AIMB-502 is designed with the Intel Q77/C216 for industrial applications that require both performance computing and enhanced power management capabilities. The motherboard supports Intel Core i7 3770 3.4GHz/ Core i5 3550S 3.0 GHz/ Core i3 3220 3.3 GHz Pentium G850 2.9 GHz/Celeron G540 2.5 GHz processor up to 8 MB L3 cache and DDR3 1333/1600 up to 32GB. -
Page 15: Graphics
Mbps and 4 USB 3.0 ports with transmission rates up to 5 Gbps. GPIO: AIMB-502 supports 14-bit GPIO from super I/O for general purpose con- trol application and 6 bit non-programmable GPIO via Phoenix connector on rear side and 8 bit programmable GPIO by pin header on board. -
Page 16: Jumpers And Connectors
Jumpers and Connectors Connectors on the AIMB-502 motherboard link it to devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to configure your system for your application. The tables below list the function of each of the board jumpers and connectors. Later sections in this chapter give instructions on setting jumpers. -
Page 17: Board Layout: Jumper And Connector Locations
Board layout: Jumper and Connector Locations Figure 1.1 Jumper and Connector Location Figure 1.2 I/O Connectors AIMB-502 User Manual... -
Page 18: Aimb-502 Board Diagram
AIMB-502 Board Diagram Figure 1.3 AIMB-502 Block Diagram AIMB-502 User Manual... -
Page 19: Safety Precautions
1, 2, and 3. In this case you connect either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when setting jumpers. AIMB-502 User Manual... -
Page 20: Cmos Clear (Cmos1)
1.8.2 CMOS Clear (CMOS1) The AIMB-502 motherboard contains a jumper that can erase CMOS data and reset the system BIOS information. Normally this jumper should be set with pins 1-2 closed. If you want to reset the CMOS data, set CMOS1 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed. -
Page 21: Pson1: Atx, At Mode Selector
However, the BIOS ME function does not keep the link/remote control after the BIOS been updated. 1.8.6 JCASE1: Case Open Sensor The AIMB-502 motherboard contains a jumper that provides a chassis open sensor. The buzzer on the motherboard beeps when the case is opened. AIMB-502 User Manual... -
Page 22: System Memory
1.11 Cache Memory The AIMB-502 supports a CPU with one of the following built-in full speed L3 caches: 8MB for Intel Xeon E3 1275v2 8MB for Intel Xeon E3 1275... -
Page 23: Pci Bus Routing Table
1.13 PCI Bus Routing Table PCI1 AD PCI slot INT AD16 AIMB-502 User Manual... - Page 24 AIMB-502 User Manual...
-
Page 25: Chapter 2 Connecting Peripherals
Chapter Connecting Peripherals... -
Page 26: Introduction
LAN / USB Ports (LAN1_USB01/LAN2_USB23/ USB89) The AIMB-502 provides up to 12 USB ports. The USB interface complies with USB Specification Rev 2.0 supporting transmission rates up to 480 Mbps and Rev 3.0 sup- porting transmission rate up to 5 Gbps with fuse protection. The USB interface can be disabled in the system BIOS setup. -
Page 27: Line Out, Mic In Connector (Audio1)
Mic In VGA/DVI-D Connector (VGA1+DVI 1) Connector AIMB-502 includes VGA and DVI interfaces that can drive conventional VGA and DVI displays. VGA is a standard 15-pin D-SUB connector commonly used for VGA. Pin assignments for VGA and DVI connectors are detailed in Appendix B. -
Page 28: Serial Ports (Com1~Com6)
Serial Ports (COM1~COM6) AIMB-502 supports six serial ports. COM1 supports RS-485 and 6 bit non-progam- mable GPIO (4 in, 2 out) and COM2 - 6 support RS-232. COM 5, 6 support 5V/12V power (JSETCOM5_V1, JSETCOM6_V1 is used to select for 5V/12V power). -
Page 29: Hdmi Port
HDMI Port eSATA Port AIMB-502 User Manual... -
Page 30: Cpu Fan Connector (Cpu_Fan1)
Due to GPIO limitation, only 2 system fan speed could be read and showed on BIOS section; SYSFAN 1 & 2 are one pair with the same fan speed, and SYSFAN 3 & 4 are one pair with the same fan speed. AIMB-502 User Manual... -
Page 31: Front Panel Connectors (Jfp1/Jfp2/Jfp3)
External speaker (JFP1/SPEAKER) JFP1/SPEAKER is a 4-pin connector for an external speaker. If there is no external speaker, the AIMB-502 provides an onboard buzzer as an alternative. To enable the buzzer, set pins 7 & 10 as closed. AIMB-502 User Manual... -
Page 32: Power Led And Keyboard Lock Connector
Connect pins 1 & 2 to (on back plane) pins 2-3 closed pins 1-2 closed panel switch via cable jumper setting System On System Suspend Fast flashes Fast flashes Fast flashes System Off Slow flashes 2.11 Mini PCIe & mSATA Slot AIMB-502 User Manual... -
Page 33: Serial Ata Interface (Sataraid1 ~ Sataraid4)
2.12 Serial ATA Interface (SATARAID1 ~ SATARAID4) 2.13 Serial ATA Interface (SATA1 ~ SATA4) AIMB-502 User Manual... -
Page 34: Digital Io Connector (Dio1)
AIMB-502 features a high performance Serial ATA interface (up to 300 MB/s) and Serial ATA III interface (up to 600 MB/s) which eases hard drive cabling with thin, space-saving cables. Note! AIMB-502 on board SATA only supports Fedora 14 and 15 and SATA mode in BIOS should be set as AHCI mode. -
Page 35: Pci Express X16 Slot (Qg2: 1 Slot/Wg2: 2 Slots)
PCI Express x16 Slot (QG2: 1 slot/WG2: 2 slots) AIMB-502 provides 1 x PCIe x16 slot (QG2 sku) or 2 x PCIe x16 slots with PCIe x8 signal (WG2 sku) support Gen3 speed slot for users to install add-on cards when their applications require higher graphic performance than the CPU embedded graphics controller can provide. -
Page 36: Front Panel Audio Connector (Fpaud1)
I/O module cable. Note! For motherboards with the optional HD Audio feature, we recommend that you connect a high-definition front panel audio module to this con- nector to take advantage of the motherboard’s high definition audio capability. AIMB-502 User Manual... -
Page 37: Atx Power Connector (Eatxpwr1, Atx12V1)
Please connect the ATX12V1 connector with the PSU ATX 12V 4- pin connector. For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 180 W. AIMB-502 User Manual... -
Page 38: Spi Flash Connector(Spi_Cn1)
2.18 SPI Flash connector(SPI_CN1) The SPI flash card pin header may be used to flash the BIOS if the AIMB-502 cannot power on. AIMB-502 User Manual... -
Page 39: Bios Operation
Chapter BIOS Operation... -
Page 40: Introduction
BIOS Setup The AIMB-502 Series system has AMI BIOS built in, with a SETUP utility that allows users to configure required settings or to activate certain system features. The SETUP saves the configuration in the FLASH of the motherboard. When the power is turned off, the battery on the board supplies the necessary power to pre- serve the FLASH. -
Page 41: Main Menu
System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS format. AIMB-502 User Manual... -
Page 42: Advanced Bios Features
Advanced BIOS Features Select the Advanced tab from the AIMB-502 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>... -
Page 43: Trusted Computing
Note! The following items function only when a TPM IC is populated on board. Security Device Support [ Disable ] AIMB-502 User Manual... -
Page 44: S5 Rtc Wake Settings
3.4.3 S5 RTC Wake Settings The item allows you enable or disable system wake up on alarm event. Wake system with Fixed Time [ Disabled ] 3.4.4 CPU Configuration AIMB-502 User Manual... - Page 45 This reduces the latency associ- ated with memory reads. Adjacent Cache Line Prefetch [ Enabled ] This item allows users to enable or disable the adjacent cache line prefetch fea- ture. AIMB-502 User Manual...
-
Page 46: Sata Configuration
This can be configured as IDE or AHCI mode. Note! There are total 10 SATA devices on AIMB-502, but only 6 SATA devices that appear in the BIOS section (SATA1~4, eSATA, and mSATA).The rest of the 4 SATA devices (SATARAID1~4) can work properly still, even if they don’t all appear in BIOS section though. -
Page 47: Intel Txt (Lt) Configuration
This item allows you to enable or disable the Intel Secure Mode Extensions (SMX) technology. Intel TXT Configuration [ Disabled ] Intel TXT support could be enabled/ disabled only when SMX is enabled. Intel VT and VT-d support must be enabled prior to TXT, also. AIMB-502 User Manual... -
Page 48: Pch-Fw Configuration
3.4.7 PCH-FW Configuration MEDS BISO Status Code [ Disabled ] This item allows you to enable or disable MDES BIOS Status Code. AIMB-502 User Manual... -
Page 49: Amt Configuration
AMT CIRA Timeout [ 0 ] Watchdog [ Disabled ] When set to [Enabled], the Watchdog timer will monitor the time taken for each task performed by a software or hardware. OS Timer [ 0 ] BIOS Timer [ 0 ] AIMB-502 User Manual... -
Page 50: Usb Configuration
USB transfer time-out [ 20 sec ] Device reset time-out [ 20 sec ] Device power-up delay [ Auto ] USB mass storage device reset time out. Mass Storage Devices [ Auto ] Shows USB storage device information. AIMB-502 User Manual... -
Page 51: Super Io Configuration
3.4.10 Super IO Configuration Super IO Chip NCT6106D Serial Port 1 Configuration Serial Port [ Enabled ] Device Setting IO=3F8h; IRQ=4 Change Settings [ Auto ] AIMB-502 User Manual... - Page 52 Serial Port [ Enabled ] Device Setting IO=2F8h; IRQ=3 Change Settings [ Auto ] Serial Port 3 Configuration Serial Port [ Enabled ] Device Setting IO=C80h; IRQ=10 Change Settings [ Auto AIMB-502 User Manual...
- Page 53 Serial Port [ Enabled ] Device Setting IO=C88h; IRQ=10 Change Settings [ Auto ] Serial Port 5 Configuration Serial Port [ Enabled ] Device Setting IO=C90h; IRQ=11 Change Settings [ Auto ] AIMB-502 User Manual...
- Page 54 Serial Port 6 Configuration Serial Port [ Enabled ] Device Setting IO=C98h; IRQ=11 Change Settings [ Auto ] Digital I/O Configuration AIMB-502 User Manual...
-
Page 55: H/W Monitor
ACPI Shutdown Temperature [ Disabled ] Use this to set the ACPI shutdown temperature threshold. When the system reaches the shutdown temperature, it will be automatically shut down by ACPI OS to protect the system from overheating damage. AIMB-502 User Manual... -
Page 56: Serial Port Console Redirection
“Enable or Disable” smart fan select for CPU fan. SYSFAN Mode Setting [ Enabled ] “Enable or Disable” smart fan select for system fan. 3.4.12 Serial Port Console Redirection Console Redirection [ Disabled ] Enable or disable the console redirection feature. AIMB-502 User Manual... -
Page 57: Cpu Ppm Configuration
CPU PPM Configuration EIST [ Enabled ] This item can enable / disable Intel CPU speed step. CPU C3 Report [ Enabled ] CPU C6 report [ Enabled ] ACPI T State [ Disabled ] AIMB-502 User Manual... -
Page 58: Chipset Configuration Setting
Users can display a Chipset Setup option by highlighting it using the <Arrow> keys. All Chipset Setup options are described in this section. The Chipset Setup screens are shown below. The sub menus are described on the following pages. 3.5.1 PCH-IO Configuration AIMB-502 User Manual... - Page 59 3.5.1.1 PCI Express Configuration PCI Express Clock Gating [ Enabled ] – PCI Express Root Port 1 (Slot 1) – PCI Express Root Port 2 (Mini PCIE) AIMB-502 User Manual...
- Page 60 Control the PCI express root port. ASPM Support [ Auto ] PCIe Speed [ Auto ] PCI Express Root Port 2 (mini PCIe solt) [ Enabled ] ASPM Support [ Auto ] PCIe Speed [ Auto ] AIMB-502 User Manual...
- Page 61 3.5.1.2 USB Configuration XHCI Pre-Boot Driver [Enabled] Enable or disable XHCI Pre-Boot Driver support. XHCI Mode [ Auto ] EHCI1 [ Enabled ] EHCI2 [ Enabled ] 3.5.1.3 PCH Azalia Configuration AIMB-502 User Manual...
-
Page 62: System Agent (Sa) Configuration
This item set for control Detection of the Azalia device. – [Disabled] = Azalia will be unconditionally disabled. – [Enabled] = Azaliz will be unconditionally enabled – [Auto] = Azaliz will be enabled if present, disabled otherwise. 3.5.2 System Agent (SA) Configuration 3.5.2.1 Graphics Configuration AIMB-502 User Manual... - Page 63 Primary Display [ Auto ] Select which of IGFX/PEG/PCI Graphics device should be primary display or select SG for switchable Gfx. Internal Graphics [ Auto ] LCD Control AIMB-502 User Manual...
- Page 64 The triple display can only work under Windows 7, it is not supported in Windows XP and Linux, and the 2nd and 3rd display can not work under DOS. 3.5.2.2 DMI Configuration DMI Vc1 Control [ Enabled ] AIMB-502 User Manual...
- Page 65 This section shows you the information about the memory you insert, included mem- ory RC version, frequency, total size, size per DIMM, minimum delay time. Max TOLUD [ Dynamic ] Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of installed graphic controller. AIMB-502 User Manual...
-
Page 66: Boot Setting
Option ROM Messages [ Force BIOS ] Force BIOS or Keep Current to set the display mode. INT19 Trap Response [ Immediate ] Enable Option ROM to trap Interrupt 19 immediately. Boot Option #1/#2 Choose boot priority from boot device. AIMB-502 User Manual... -
Page 67: Security Setting
Select this option and press <ENTER> to access the sub menu, and then type in the password. Set the Administrator password. User Password Select this option and press <ENTER> to access the sub menu, and then type in the password. Set the User Password. AIMB-502 User Manual... -
Page 68: Save & Exit Configuration
Select Restore Defaults from the Exit menu and press <Enter>. Save as User Default Save the all current settings as a user default. Restore User Default Restore all settings to user default values. Boot Override Shows the boot device types on the system. AIMB-502 User Manual... -
Page 69: Software Introduction & Service
Chapter Software Introduction & Service... -
Page 70: Introduction
Introduction The mission of Advantech Embedded Software Services is to "Enhance quality of life with Advantech platforms and Microsoft® Windows® embedded technology." We enable Windows® Embedded software products on Advantech platforms to more effectively support the embedded computing community. Customers are freed from the hassle of dealing with multiple vendors (hardware suppliers, system integrators, embedded OS distributors) for projects. -
Page 71: Software Utility
It contains valuable intellectual property, design knowledge and innovation - but it is easy to be copy. Embedded Security ID utility provides reliable security functions for customers to secure their application data within embedded BIOS. AIMB-502 User Manual... - Page 72 Telnet server and FTP server so the administrator can attempt to rescue the system. Note: This function requires BIOS customization. AIMB-502 User Manual...
-
Page 73: Chipset Software Installation Utility
Chapter Chipset Software Installation Utility... -
Page 74: Before You Begin
To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for AIMB-502 are located on the software installation CD. The driver in the folder of the driver CD will guide and link you to the utilities and drivers under a Windows system. -
Page 75: Windows Xp/Windows 7 Driver Setup
Windows XP/Windows 7 Driver Setup Insert the driver CD into your system's CD-ROM drive. Navigate to the "01. Chip" folder and click "infinst.autol.exe" to complete driver installation. AIMB-502 User Manual... - Page 76 AIMB-502 User Manual...
-
Page 77: Vga Setup
Chapter VGA Setup... -
Page 78: Introduction
See Chapter 5 for information on installing the CSI utility. Insert the driver CD into your system's CD-ROM drive. Navigate to the "VGA" folder and click "setup.exe" to complete the installation of the drivers for Windows 7 and Windows XP. AIMB-502 User Manual... - Page 79 AIMB-502 User Manual...
- Page 80 AIMB-502 User Manual...
-
Page 81: Chapter 7 Lan Configuration
Chapter LAN Configuration... -
Page 82: Introduction
Introduction The AIMB-502 has dual Gigabit Ethernet LANs via dedicated PCI Express x1 lanes (Intel 82579LM (LAN1) and 82583V (LAN2)) that offer bandwidth of up to 500 MB/ sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ether- net at 1000 Mbps. -
Page 83: Windows® 7/Xp Driver Setup (Intel 82579Lm/82574L)
Windows® 7/XP Driver Setup (Intel 82579LM/ 82574L) Insert the driver CD into your system's CD-ROM drive. Select the LAN folder then navigate to the directory for your OS. AIMB-502 User Manual... - Page 84 AIMB-502 User Manual...
- Page 85 Appendix Programming the Watchdog Timer...
-
Page 86: Appendix A Programming The Watchdog Timer
Programming the Watchdog Timer AIMB-502's watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to program it. - Page 87 Unlock NCT6106D Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog timer Lock NCT6106D AIMB-502 User Manual...
-
Page 88: Table A.1: Watchdog Timer Registers
Bit 5: Write 1 to generate a timeout signal immedi- ately and automatically return to 0. [default=0] Bit 4: Read status of watchdog timer, 1 means timer is “timeout”. Write this address to I/O port 2E (hex) to lock the AA (hex) ----- watchdog timer 2. AIMB-502 User Manual... -
Page 89: Example Program
Inc dx Mov al,10 Out dx,al ;----------------------------------------------------------- Dec dx ; Lock NCT6106D Mov al,0aah Out dx,al Enable watchdog timer and set 5 minutes as timeout interval ;----------------------------------------------------------- Mov dx,2eh ; Unlock NCT6106D Mov al,87h Out dx,al Out dx,al AIMB-502 User Manual... - Page 90 Enable watchdog timer to be reset by mouse ;----------------------------------------------------------- Mov dx,2eh ; Unlock NCT6106D Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- AIMB-502 User Manual...
- Page 91 Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f2h Out dx,al Inc dx In al,dx Or al,40h Out dx,al AIMB-502 User Manual...
- Page 92 Dec dx ; Generate a time-out signal Mov al,0f2h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------- Dec dx ; Lock NCT6106D Mov al,0aah Out dx,al AIMB-502 User Manual...
-
Page 93: Appendix B Pin Assignments
Appendix Pin Assignments... -
Page 94: Interface (Com2)
COM2_RTS# COM2_SOUT RS-232 Interface (COM3456) Table B.2: RS-232 Serial Port (COM3456) Pin Name Pin Name COM3_DCD# COM3_DSR# COM3_SIN COM3_RTS# COM3_SOUT COM3_CTS# COM3_DTR# COM3_RI# COM4_DCD# COM4_DSR# COM4_SIN COM4_RTS# COM4_SOUT COM4_CTS# COM4_DTR# COM4_RI# COM5_DCD# COM5_DSR# COM5_SIN COM5_RTS# COM5_SOUT COM5_CTS# AIMB-502 User Manual... -
Page 95: Usb 2.0 Header (Usb89)
COM6_DTR# COM6_RI# USB 2.0 Header (USB89) Table B.3: USB 2.0 Header (COM89) Pin Name Pin Name + V5 USB8N USB9N USB8P USB9P Serial ATA III (SATA 1~2) Table B.4: Serial ATA III (6Gb/s) Pin Name Pin Name AIMB-502 User Manual... -
Page 96: Serial Ata Ii (Sata 3~4, Sataraid1~4)
Serial ATA II (SATA 3~4, SATARAID1~4) Table B.5: Serial ATA II (3Gb/s) Pin Name Pin Name AT/ATX Mode Connector (PSON1) Table B.6: AT/ATX Mode Connector (PSON1) Pin Name +V3.3 * ATX mode (2-3 short) / AT mode (1-2 short) AIMB-502 User Manual... -
Page 97: Atx Power Connector (Eatpwr1)
Table B.7: ATX 24 pin main power connector Pin Name Pin Name +3.3V +3.3V +3.3V -12V PS_ON# ATXPG 5VSB +12V +12V +3.3V ATX 12 V Connector (ATX12V1) Table B.8: ATX 4 pin main power connector (ATX12V1) Pin Name +V12_4P +V12_4P AIMB-502 User Manual... -
Page 98: Cpu Fan Connector (Cpufan1)
Table B.10: System Fan Power Connector (SYS_FAN1~4) Pin Name SYS_FAN_PWN SYS_FAN_SPEED B.11 Audio front panel connector (FPAUD1) Table B.11: Audio front panel connector (FPAUD1) Pin Name Pin Name MIC2_L AGND MIC2_R PRESENCE# LINE2-R MIC2-JD FRONT-IO-SENSE_R LINE2-L LINE2-JD AIMB-502 User Manual... -
Page 99: Digital Io Connect (Dio1)
SIO_GPO9 SIO_GPI6 SIO_GPO5 +V5_DUAL SIO_GPI7 SIO_GPO6 +V5_DUAL SIO_GPI8 B.13 LAN LED (LANLED1) Table B.13: GbE LAN LED (LANLED1) Pin Name Pin Name LAN1LED0 (LINK/ACTIVITY) LAN2_LED2 (LINK1000) LAN2LED1 (LINK/ACTIVITY) LAN1_LED2 (LINK100) +V3.3_LAN LAN2_LED0 ((LINK100) +V3.3_LAN +V3.3_LAN LAN1LED1 (LINK1000) AIMB-502 User Manual... -
Page 100: Spi Flash Update Connector (Spi_Cn1)
Pin Name +3.3V_SPI SPI_CS# SPI_CLK SPI_SO_R1 SPI_SI B.15 COM5 / 6_RI selector Jumper setting (JSETCOM5_V1/ JSETCOM6_V1) Table B.15: COM5 / 6_RI selector Jumper setting (JSETCOM5_V1/ JSETCOM6_V1) Pin Name Pin Name COM5(6)_RI# COM5(6)_RI_VA# (CONN) +12V COM5(6)_RI_VA#(CONN ) COM5(6)_RI_VA#(CONN) AIMB-502 User Manual... -
Page 101: Power Switch/Hdd Led/Speaker (Jfp1+Jfp2)
SMB_CLK_RESUME B.17 Power LED (JFP3) You can use an LED to indicate when the single board computer is on. Pin 1 of JFP3 supplies the LED's power. Table B.17: Power LED (JFP3) Pin Name Pin Name SUSLED AIMB-502 User Manual... -
Page 102: Irda Connector (Jir1)
Case Open sensor (JCASE1) Table B.19: Case Open sensor (JCASE1) Pin Name CASEOP# B.20 Case Open Mode Connector (JCASEOP_SW1) Table B.20: Case Open Mode Connector (JCASEOP_SW1) Pin Name CASEOP# HWM_CASEOP# CASEOP (1-2) Normal close / (2-3) Normal open AIMB-502 User Manual... - Page 103 Pin Name Pin Name N.C. COM1_RS485P COM1_RS485N COM1_RS485P_T COM1_RS485N_T (1-2): System wasn’t set as terminal point / (2-3): System was set as terminal point. This setting on J485P & J485N should be matched at the same time. AIMB-502 User Manual...
- Page 104 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2013...
Need help?
Do you have a question about the AIMB-502 and is the answer not in the manual?
Questions and answers