Hilti AG 700-14D Operating Instructions Manual

Hilti AG 700-14D Operating Instructions Manual

Hide thumbs Also See for AG 700-14D:

Advertisement

Printed: 02.04.2014 | Doc-Nr: PUB / 5169300 / 000 / 01
AG 700-14D
Operating instructions
Mode d'emploi
Manual de instrucciones
Manual de instruções
en
fr
es
pt

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AG 700-14D and is the answer not in the manual?

Questions and answers

Summary of Contents for Hilti AG 700-14D

  • Page 1 AG 700-14D Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 02.04.2014 | Doc-Nr: PUB / 5169300 / 000 / 01...
  • Page 2 This Product is Listed Ce produit est homologué Producto homologado por Este produto está registrado Printed: 02.04.2014 | Doc-Nr: PUB / 5169300 / 000 / 01...
  • Page 3 Printed: 02.04.2014 | Doc-Nr: PUB / 5169300 / 000 / 01...
  • Page 4 Printed: 02.04.2014 | Doc-Nr: PUB / 5169300 / 000 / 01...
  • Page 5: Table Of Contents

    In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the AG 700-14D angle gether with the power tool. grinder. Ensure that the operating instructions are Parts, operating controls and indicators 1 with the power tool when it is given to other persons.
  • Page 6: Description

    Take the influences of the surrounding area into account. Do not use the power tool or appliance where there is a risk of fire or explosion. Nationally applicable industrial safety regulations must be observed. To avoid the risk of injury, use only genuine Hilti accessories and insert tools.
  • Page 7 Observe the information printed in the operating instructions concerning operation, care and maintenance. The power tool is designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any special hazards that may be encountered. The power tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed.
  • Page 8: Consumables

    Clamping flange (not for use with accessories with integrated thread) 4 Technical data Right of technical changes reserved. Power tool AG 700-14D Rated power input 120 V Rated current input 15 A Rated frequency 60 Hz Rated speed 8,500/min Max.
  • Page 9: Safety Instructions

    5 Safety instructions protection used for appropriate conditions will reduce 5.1 General Power Tool Safety Warnings personal injuries. WARNING c) Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power Read all safety warnings and instructions. Failure source and/or battery pack, picking up or carrying to follow the warnings and instructions may result the tool.
  • Page 10 filtrating particles generated by your operation. Pro- 5.1.5 Service longed exposure to high intensity noise may cause a) Have your power tool serviced by a qualified repair hearing loss. person using only identical replacement parts. Keep bystanders a safe distance away from This will ensure that the safety of the power tool is work area.
  • Page 11 5.5 Additional safety warnings specific for abrasive is defective. Have the tool repaired at an authorized cutting-off operations Hilti service center right away. a) Do not "jam" the cut-off wheel or apply excessive h) Children must be instructed not to play with the pressure.
  • Page 12 Allowing dust to get into your mouth, should be checked at regular intervals at a Hilti eyes, or to remain on your skin may promote absorp- Service Center. Under unfavorable circumstances, tion of harmful chemicals.
  • Page 13: Before Use

    6 Before use To remove the guard from the power tool, follow the instructions for fitting the guard but carry out the steps in the reverse order. 6.2.2 Adjusting the guard or guard with cover plate 4 DANGER Disconnect the plug from the power source before Release the clamping lever.
  • Page 14: Operation

    Improve the blood circulation in your fingers by re- defective. Have the tool repaired at an authorized Hilti laxing your hands and exercising your fingers during service center right away.
  • Page 15: Care And Maintenance

    Press the on/off switch as far as it will go. 7.3.1 Switching on (AG 700-14D) 7 In this way, the hand is closed around the power Plug the supply cord into the power outlet. tool, which ensures optimum safety while working.
  • Page 16: Disposal

    10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information.
  • Page 17 Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 4331 | 0214 | 00-Pos. 3 | 1 Printed in China © 2014 Right of technical and programme changes reserved S. E. & O.

Table of Contents