ORIGINAL OPERATING INSTRUCTIONS AG 125-A22 angle grinder 1 These numbers refer to the illustrations. You can It is essential that the operating instructions find the illustrations at the beginning of the operating are read before the power tool is operated for instructions.
80 m/sec. The power tool may be used only for dry cutting or grinding. When grinding stone, a vacuum cleaner equipped with the appropriate filter, e.g. a suitable Hilti vacuum cleaner, must be used. Working on materials hazardous to the health (e.g. asbestos) is not permissible.
Page 7
It is recommended that a dust removal system consisting of matched components, i.e. dust removal hood and a suitable Hilti vacuum cleaner, are used for cutting and slitting mineral materials, such as concrete or stone. These serve to protect the operator and increase the life of the power tool and disc used.
It is recommended that a dust removal system consisting of matched components, i.e. dust removal hood and a suitable Hilti vacuum cleaner, are used for cutting and slitting mineral materials, such as concrete or stone. These serve to protect the operator and increase the life of the power tool and disc used.
Item Equipment AC‑D AG-D AF-D AN-D DG‑CW DC‑D DC‑EX 125/5"-C com- pact guard (in combin- ation with A) Side handle DC BG 125 hoop-handle (optional for F) Clamping nut Clamping flange Kwick-Lock (optional for H) 4 Technical data Right of technical changes reserved. Power tool AG 125‑A22 Rated voltage...
Noise information (as perEN 60745‑2‑3): Typical A-weighted sound power level 94 dB (A) Typical A-weighted emission sound pressure level 83 dB (A) Uncertainty for the given sound level 3 dB (A) Vibration information in accordance with EN 60745 Triaxial vibration value (vibration vector sum) for the Measured in accordance with EN 60745‑2‑3 AG 125‑A22 Surface grinding using the vibration-absorbing side...
Page 11
e) Do not overreach. Keep proper footing and bal- d) Under abusive conditions, liquid may be ejected ance at all times. This enables better control of the from the battery; avoid contact. If contact acci- dentally occurs, flush with water. If liquid contacts power tool in unexpected situations.
Page 12
capable of stopping small abrasive or workpiece kickback forces. Always use auxiliary handle, if fragments. The eye protection must be capable of provided, for maximum control over kickback or stopping flying debris generated by various opera- torque reaction during start-up. The operator can tions.
Page 13
To achieve a high level wiring or objects that can cause kickback. of dust collection, use a suitable vacuum cleaner of the type recommended by Hilti for wood dust and/or mineral dust together with this tool. Ensure 5.6 Additional safety instructions that the workplace is well ventilated.
Contact Hilti the spindle due to the braking effect of the motor. Service after the battery has cooled down.
Page 15
Take care to ensure that the closed side of the guard is switch interlock activated before fitting the battery. always positioned toward the operator’s body. Use only the Hilti batteries approved for use with this Adjust the position of the guard to suit the requirements power tool.
Page 16
CAUTION Do not press the spindle lockbutton 6.7.3 Fitting and removing the front cover 9 before the drive spindle has stopped rotating. NOTE Press the spindle lockbutton and hold it in this If you use the front cover, fit it by pushing it onto the position.
7 Operation CAUTION The insert tool may get hot during use. Wear protective gloves when changing insert tools. WARNING WARNING Reduce the load on the power tool by avoiding tilting Wear personal protective equipment. Exposure to the disc in the kerf when cutting. The disc or wheel noise can cause hearing loss.
Have fully with a dry brush. Do not permit foreign objects to the power tool repaired by Hilti Service. enter the interior of the tool. The motor’s fan will draw dust into the casing and an excessive accumulation of WARNING conductive dust (e.g.
10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information.
Need help?
Do you have a question about the AG 125-A22 and is the answer not in the manual?
Questions and answers