Ul Alarm / Alarm Reset Button; Gate Status Monitoring; Open / Stop / Close Connection; Closing Photocell Connection - Max Phantom 2000 Installation And Owner's Manual

UL alarm / Alarm Reset button

A UL ALARM (strobe light) can be connected. It will turn ON
when the GATE IN MOTION - Mode 0 and/or Mode 1 are
turned ON (see page 28).
Press RESET BUTTON to turn OFF
activated strobe light.
Press RESET BUTTON to turn OFF
an activated alarm.

gate status monitoring

GATE STATUS LEDs will turn ON when gate is in the OPEN or
CLOSED position.
Connect a gate monitoring device to GATE STATUS relays to
show if gate is in the OPEN or CLOSED position.
OPEN/COM Relay: Show if gate is in the OPEN position.
CLOSE/COM Relay: Show if gate is in the CLOSED position.

open / stop / close Connection

The OPEN/STOP/CLOSE inputs will allow a standard 4-wire
3-Button Station or an additional External RESET Button to be
connected.
Corresponding LEDs will light when each button is activated.

closing photocell connection

The PHOTOCELL input will allow a CLOSING DIRECTION PHOTOCELL to
be connected. 12V or 24V power can be supplied for the photocells.
NOTE: This input is NOT UL SAFETY PHOTOCELL. ALL UL inputs MUST
be made at the MAX MC-100 motor controller on the gate operator.
INSIDE Property
OUTSIDE Property
32
matrix 1
Factory Wired
Reset Button
3-Button
Station
CLOSING
GATE
12V or 24V
DIRECTION
Photocells
UL ALARM 12V
ALARM RET
RESET
GND
Strobe
Light
OPEN
GATE
COM
STATUS
CLOSE
Remote Gate E N
O P
T E
G A
Monitoring Device
E D
in Remote Location
O S
C L
T E
G A
OPEN
STOP
STOP
S
E S
P R
Com
CLOSE
S E
R E
t o
Com
Additional External
Reset Button
Choose 12 VDC OR 24 VDC
(250 mA Max.)
12VDC
GND
24VDC
GND
Power
GND
N.O.
GND
MATRIX 1
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
MADE in USA LEAVE OPEN OPEN OPEN MAG
LEFT RIGHT
OPEN 1 TIME OFF 1.5Sec 2Sec
LOCK
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI Tamper NO
EXIT CENTER SAFETY GATE
TAILGATE
TAMPER
OFF
Tamper IN
PHOTOCELL
UL EDGE 1
SAFETY
MIN MAX
OFF ENTRAP ENTRAP EDGE 2
CLOSE TIMER
ID PLUG ID PLUG
MOTOR MOTION ERROR ERROR
UL ALARM 12V
ALARM RET
OPEN OPEN STOP STOP CLOSE CLOSE
POSITION
RECORDER
MAX REVERSE SENSITIVITY TIVITY
12VDC
GATE SPEED
GND MOTOR OVERLOAD
OBD PORT
GATE
BLACK BOX
MIN NO LIMIT SWITCH /
STATUS
24VDC CLAMP SLIPPING
MAX
GND
LIMIT
BATTERY
SWITCH
ON-LINE
MOTOR
ON-LINE
PRIMARY SEC
GATE GATE
MATRIX 1
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
MADE in USA LEAVE OPEN OPEN OPEN MAG
LEFT RIGHT
OPEN 1 TIME OFF 1.5Sec 2Sec LOCK
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI Tamper NO
EXIT CENTER SAFETY GATE
TAILGATE
TAMPER
EXIT
ON OFF
Tamper IN
CENTER CENTER
PHOTOCELL
UL EDGE 1
SAFETY SAFETY
MIN MIN MAX MAX
OFF OFF ENTRAP EDGE 2
CLOSE TIMER CLOSE TIMER
ID PLUG
PARTIAL PARTIAL ERROR
OPEN OPEN
ID ID
PLUG PLUG
UL UL ALARM 12V
ALARM RET ALAR
OPEN
POSITION POSITION
RECORDER RECORDER
MAX MAX
12VDC 12VDC
GND OBD PORT OBD PORT
BLACK BOX BLACK BOX GATE
MIN MIN
STATUS STATUS
24VDC
MAX
GND
LIMIT
BATTERY
SWITCH
ON-LINE
MOTOR
ON-LINE
PRIMARY SEC
GATE GATE
MATRIX 1
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
MADE in USA LEAVE OPEN OPEN OPEN MAG
OPEN 1 TIME LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI Tamper NO
TAILGATE EXIT CENTER SAFETY GATE
TAMPER
EXIT
ON OFF
Tamper IN
CENTER
PHOTOCELL
UL EDGE 1
SAFETY SAFETY
MIN MAX
OFF
ENTRAP EDGE 2
CLOSE TIMER CLOSE TIME
ID PLUG
PARTIAL PARTIAL MOTOR MOTION ERROR
OPEN OPEN
ID
PLUG
UL ALARM 12V
ALARM RET
OPEN OPEN STOP CLOSE
POSITION ON
RECORDER
MAX MAX REVERSE SENSITIVITY REVERSE
12VDC
GATE SPEED GATE SPEED
GND OBD PORT MOTOR OVERLOAD MOTOR OVERL
BLACK BOX GATE
MIN NO LIMIT SWITCH / NO LIMIT SWITCH /
STATUS
24VDC CLAMP SLIPPING CLAMP SLIPPING
MAX
GND GN
LIMIT
BATTERY
SWITCH
ON-LINE
MOTOR
ON-LINE
PRIMARY SEC
GATE GATE
T
MATRIX 1
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
OPEN OPEN
MADE in USA LEAVE OPEN MAG
OPEN 1 TIME LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI Tamper NO
GATE
TAILGATE EXIT CENTER SAFETY
TAMPER
EXIT
ON OFF
Tamper IN
CENTER
PHOTOCELL
UL EDGE 1
SAFETY
MIN MAX
OFF
ENTRAP EDGE 2
CLOSE TIMER
ID PLUG
PARTIAL MOTOR MOTION ERROR
OPEN
ID ID
PLUG PLUG
UL ALARM 12V
ALARM RET
OPEN STOP CLOSE
POSITION
RECORDER
MAX REVERSE SENSITIVITY
12VDC
GATE SPEED
GND OBD PORT MOTOR OVERLOAD
BLACK BOX GATE
MIN
NO LIMIT SWITCH /
STATUS
24VDC 24VD CLAMP SLIPPING
MAX
GND GND
LIMIT
BATTERY
SWITCH
ON-LINE
MOTOR
ON-LINE
PRIMARY SEC
GATE GATE
Additional CLOSING Cycle
Photocells can be connected.
COM
NC
COM
GND
RESET
GND G
OPEN
COM
CLOSE
IN USE
POWER
COM
NC
COM
GND
RESET RESET
GND GND
OPEN
COM
CL CLOSE
IN USE
POWER
COM
NC
COM
GND
RESET
GND
OPEN
COM
CLOSE
IN USE
POWER
COM
NC
COM
GND
RESET
GND
OPEN
COM
CLOSE
IN USE
POWER