Id Plug; Gate Tamper; Ul Entrapment Leds; Emergency Vehicle/Max Open Inputs - Max Phantom 2000 Installation And Owner's Manual

id plug

AN ID Plug comes standard on Matrix 1. It identifies the type
of gate operator and MUST be plugged in or the Matrix 1 WILL
NOT function.
ID PLUG ERROR LED: Will light when ID PLUG is missing.

Gate Tamper

The GATE TAMPER can be used for various functions such as
turning a warning light, siren or camera on when the gate is
tampered with - Vandalized Gate, see below.
TAMPER NO/Com Relay: Connect a warning light, siren or
camera to relay.
TAMPER IN/GND Input: Connect a sensor device to input.
When Tamper In/GND gets triggered, device that is wired to
Tamper NO/Com will activate.
Vandalized Gate: The gate operator defines a "Vandalized
Gate" as UNAUTHORIZED movement of the gate's close limit
switch. This can occur if the red release handle clamp is lifted
and gate is manually moved or the gate is pushed open without
authorization. These will trigger the Gate Tamper relay.

UL entrapment LEDs

UL ENTRAPMENT LEDs will indicate when a OPENING DIRECTION
Photocell and/or Reversing Edge(s) have been activated. If alarm gets
triggered, press reset button on control box to turn alarm off.
NOTE: UL safety approved devices are wired to the MC-100 motor
controllers ONLY. DO NOT wire them to the Matrix 1.
REVERSE SENSITIVITY LED: Will light when the gate encounters an
obstruction triggering the ERD sensor.

emergency vehicle/max open inputs

FIRE DEPT lnput: Should be connected to a knox box device to allow
the proper authorities to gain emergency access when necessary. The
input will override the GATE DISABLE input and allow EMERGENCY
personnel FULL 24/7 access. Gate fully opens.
MAX OPEN Input: Can be connected to a key switch and used as an
ADDITIONAL input from the FIRE DEPT input. The input will override
the GATE DISABLE input and allow SECURITY personnel FULL 24/7
access. Gate fully opens.
30
matrix 1
Low Profile Swing
ID Plug
Siren
Power
GATE
TAMPER
Knox
MATRIX 1
ID PLUG
MADE in USA
ERROR
SAFETY
ID
PLUG
12 12VDC
ID
GND
PLUG
24VDC
GND
Warning
Light
Security
Camera
MATRIX 1
MADE in USA
EXIT EXIT
CENTER
SAFETY
Tamper NO
COM
ID ID
PLUG PLUG
GND
12VDC
Tamper IN
GND
24VDC
GND
Motion
Sensor
MATRIX 1
MADE in USA
PHOTOCELL
EXIT
EDGE 1
UL
CENTER
SAFETY
EDGE 2
ENTRAP
ID
PLUG
12VDC
GND ND
24VDC 24VDC
GND GND
REVERSE SENSITIVITY
MATRIX 1
MADE in USA
EXIT
CENTER
SAFETY
ID ID
PLUG PLUG
12VDC 12VDC
GND GND
24VDC DC
GND
Key
Box Switch
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
OPEN OPEN
LEAVE OPEN MAG
OPEN 1 TIME LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
COM
NC
AU AUTOMATIC OPEN/CLOSE CONTROLS
Tamper NO
ANTI ANTI
GATE
TAILGATE TAILGATE EX EXIT CENTER SAFETY
COM
TAMPER
GND
Tamper IN
PHOTOCELL
EDGE 1
MIN
OFF
ENTRAP ENTRAP EDGE 2 EDGE 2
CLOSE TIMER
ID PLUG
PARTIAL
ER ERROR
OPEN
UL ALARM 12V
ALARM RET
RESET
OPEN STOP CLOSE
POSITION GND
RECORDER
MAX REVERSE SENSITIVITY
GATE SPEED
OBD PORT MOTOR OVERLOAD
OPEN
BLACK BOX GATE
MIN
NO LIMIT SWITCH /
STATUS COM
CLAMP SLIPPING
MAX
CLOSE
LIMIT BATTERY
SWITCH
IN USE
ON-LINE
MOTOR
ON-LINE POWER
PRIMARY SEC
GATE GATE
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
LEAVE OPEN OPEN OPEN MAG
LEFT RIGHT
OPEN 1 TIME OFF 1.5Sec 2Sec
LOCK
COM
NC
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI Tamp Tamper NO
GA GATE
TAILGATE TAILGATE EXIT EXIT COM
TAMPER
GND
ON ON OFF OFF
Tamper IN
PHOTOC PHOTOCELL
EDGE 1
MIN MIN MAX MAX
OFF OFF EDGE 2
ENTRAP
CLOSE TIMER CLOSE TIMER
ID PLUG
PARTIAL PARTIAL MOTOR MOTION ERROR
OPEN OPEN
UL ALARM 12V
ALARM RET
OPEN STOP CLOSE RESET
POSITION GND
RECORDER
MAX REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
OBD PORT
OPEN
BLACK BOX GATE
MIN NO LIMIT SWITCH /
COM
STATUS
CLAMP SLIPPING
MAX
CLOSE
LIMIT BATTERY
SWITCH
ON-LINE IN USE
MOTOR
POWER
ON-LINE
PRIMARY SEC
GATE GATE
BATTERY PRIMARY
BACK-UP MODE GATE
MAGLOCK
LEAVE
CLOSED
DELAY
LEAVE OPEN OPEN OPEN MAG
LEFT RIGHT
OPEN 1 TIME OFF 1.5Sec 2Sec
LOCK
COM
NC
AUTOMATIC OPEN/ AUTOMATIC OPEN/CLOSE CONTROLS
ANTI ANTI Tamper NO
GATE
TAILGATE TAILGATE EXIT EXIT CENTER CENTER SAFETY SAFETY COM
TAMPER
GND
ON OFF
Tamper IN Tam
PHOTOCELL
EDGE 1
UL
MIN MAX
OFF EDGE 2
ENTRAP
CLOSE TIMER
ID PLUG ID PLUG
PARTIAL PARTIAL MOTOR MOTION MOTOR MOTION ERROR
OPEN OPEN
UL ALARM 12V
ALARM RET
OPEN STOP STOP CLOSE CLOSE RESET
POSITION GND
MAX MAX REVERSE SENSITIVITY REVERSE SEN
GATE SP GATE SPEED ED
MOTOR OVERLOAD MOTOR OVERLOAD
OPEN
GATE
NO LIMIT SWIT NO LIMIT SWITCH / COM
STATUS
CLAMP SLIPPING CLAM
CLOSE
LIMIT BATTERY
SWITCH
ON-LINE IN USE
MOTOR
POWER
ON-LINE
PRIMARY SEC
GATE GATE
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
OPEN OPEN MAG
LEAVE OPEN
OPEN 1 TIME LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
COM
NC
AUTOMATIC OPEN/CLOSE CONTROLS
Tamper NO
ANTI
GATE
TAILGATE EXIT CENTER SAFETY COM
TAMPER
GND
ON OFF
Tamper IN
PHOTOCELL
EDGE 1
UL
MIN MAX
OFF EDGE 2
ENTRAP
CLOSE TIMER
ID PLUG
PARTIAL MOTOR MOTION ERROR
OPEN
UL ALARM 12V
ALARM RET
OPEN STOP CLOSE RESET
POSITION GND
RECORDER
MAX
REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
OBD PORT
OPEN
BLACK BOX GATE
MIN
NO LIMIT SWITCH / COM
STATUS
CLAMP SLIPPING
MAX
CLOSE
LIMIT BATTERY
SWITCH
IN USE
ON-LINE
MOTOR
POWER
ON-LINE
PRIMARY SEC
GATE GATE