System Operation - Ideal Security SK634 Instruction Manual

SYSTEM OPERATION

1. TO ARM THE SYSTEM
• Enter password followed by the ARM/DISARM button or press the ARM button on the remote control.
• Three short beeps will sound and the ARM icon will show on the auto-dialer screen.
• Wait 60 seconds for a short beep. The auto-dialer is now set at ARM and ready to receive signals.
• If an OPEN ZONE condition exists (a door or window is open) the auto dialer will beep for 5 seconds and the screen will
show "CLOSE PLEASE" and the zone number of the sensor that triggered the alarm will be flashing. If the zone remains
open (the door or window is not closed) after 60 seconds the alarm will sound and the auto dialer will start dialing.
2. ALARM OPTIONS
• If the auto-dialer (in ARM mode) receives a signal from any sensor, the screen will display TRIGGER with the zone
number. After the entry time delay it will sound a SIREN for 30 seconds on, 30 seconds off and 30 seconds on, and will
automatically dial all the numbers stored, one by one, for the number of cycles (amount of times the numbers are dialed)
you have chosen. The receiver of the phone call will hear a prerecorded message and will have option to listen in or
broad cast to the room the auto-dialer is located in. The receiver of the call can then take appropriate action.
• In ARM mode, if the auto-dialer is set to SIREN OFF, the numbers stored will be dialed silently. No siren will be heard from
the auto-dialer. NOTE: The INDOOR/OUTDOOR SIREN must also be set to OFF for silent operation.
3. TO DISARM THE SYSTEM FROM THE AUTO DIALER KEY PAD
• Enter password followed by the ARM/DISARM button on the auto dialer. Or press on DISARM button on the remote.
• You will hear one beep and the ARM icon will disappear from the auto-dialer screen to confirm that the Auto-Dialer has
been disarmed.
• Before dialing the auto dialer will detect if a phone line is connected, if no telephone line is connected the auto dialer will
beep 4 times and the alarm will sound without dialing.
4. PANIC BUTTON
• If you press "PANIC" button on auto-dialer or remote control, the ALARM will sound instantly for 30 seconds, then off for
30 seconds, then on for 30 seconds and then off, and the auto-dialer will begin dialing the stored numbers immediately.
• To stop the alarm sound and the dialing, enter password then press ARM/DISARM button or press the DISARM
button on the remote.
5. REMOTE OPERATION BY TELEPHONE.
(What you can do when you receive a call from the system)
Answer the call. You will hear your personalized message. The message will repeat 3 times. If no function codes are entered
by the receiver of the call, the system will hang up and dial the next number programed.
You may enter the following codes on your phone key pad. Once a code is entered you will hear a beep for confirmation.
Function
Room Monitor
Broadcast to room
End of Call
DISARM System
6. REMOTE ACTIVATION BY TELEPHONE
(To control your auto dialer via telephone)
• Using a seperate telephone line dial your home telephone number.
• The auto-dialer will answer after the set amount of rings that you programmed.
• Once connected enter your PASSWORD, you will hear two beeps (confirmation).
• Enter key combination listed below for desired function you would like to perform.
ROOM MONITOR – Enter "1 and #" after the beep you will be able to listen into the room where the auto-dialer is installed.
After 30 seconds you will hear a beep to remind you that if you do not enter another code within 20 seconds the call will end.
The total duration of the room monitor is 50 seconds if no other codes are entered.
BROADCAST TO ROOM – Enter "2 and #" after the beep you will be able to broadcast into the room where the auto-dialer is
installed. After 30 seconds you will hear a beep to remind you that if you do not enter another code within 20 seconds the call
will end. The total broadcast time is 50 seconds if no other codes are entered.
Press Keys
1 and #
2 and #
3 and #
6 and #