Black & Decker glc2500 Manual page 7

Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
To fit the battery (14), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (18) while

at the same time pulling the battery out of the receptacle.
Assembling the guard (fig. C)
Place the pin (19) of the guard into the hole (20).

Place the tongue (21) into the slot (22) until it locks into

place.
Fit the screw (23) and tighten the screw.

Fitting the guard (fig. D)
Warning! Never operate the tool with damaged guards or
shields or without guards or shield in place.
Place the guard (9) onto the tool as shown, aligning the

holes (24) with the lugs (25) on the tool.
Press the guard until it snaps into place (A).

Push the guard forward (B).

Securely tighten the screws (26).

Warning! Never use the tool unless the guard is properly fitted.
Fitting a new spool of cutting line (fig. E)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6481).
Keep the tabs (27) on the spool cover (28) depressed and

remove the spool cover from the housing (12).
Remove the empty spool (29) from the housing.

Remove any dirt and grass from the housing.

Take the new spool and unwind approx. 12 cm of cutting line.

Feed the cutting line through the eyelet (30).

Push the spool onto the drive shaft (31) and rotate it

slightly until it is seated. Make sure that the cutting line is
not trapped under the spool and that 10-12 cm of cutting
line protrudes from the housing.
Align the tabs on the spool cover with the holes in the

housing.
Push the cover onto the housing until it snaps into place.

Warning! If the cutting line protrudes beyond the trimming
blade (10), cut it off so that it just reaches the blade.
Winding new line onto an empty spool (fig. F - H)
You may wind new cutting line onto an empty spool.
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6170 (25 m), A6171 (40 m)).
Remove the empty spool from the tool as described above.

Remove any old cutting line from the spool (32) (fig. F).

Feed 2 cm of cutting line into one of the holes (33) in the

spool as shown (fig. G).
Bend the cutting line and anchor it in the L-shaped slot (34).

Wind the cutting line onto the spool in the direction of the

arrow. Make sure to wind the line on neatly and in layers.
Do not criss-cross (fig. H).
When the wound cutting line reaches the recesses (35),

cut the line. Let the line protrude approx. 12 cm from the
spool and hold a finger on the line to keep it in place (fig. F).
Proceed as described above to fit the spool on the tool.

Warning! Only use the appropriate type of Black & Decker
cutting line.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. When charging the battery for the first
time, or after prolonged storage, it will only accept an 80%
charge. After several charge and discharge cycles, the battery
will attain full capacity. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
To charge the battery (14), remove it from the tool and

insert it into the charger (15). The battery will only fit into
the charger in one way. Do not force. Be sure that the
battery is fully seated in the charger.
Plug in the charger.

8 hour charger
The battery will be fully charged in approx. 8 hours.
Avoid leaving the battery in the charger for more than 24 hours.
If the battery is left for long periods of time, fully charge the
battery periodically. Uncharged batteries left for long periods
will lose capacity and will not perform optimally.
Hint: Charge the battery overnight. Discharge the battery
(using the tool) for the first six charges to ensure maximum
performance of the battery.
Adjusting the position of the secondary handle (fig. I)
The secondary handle (4) can be adjusted to provide optimum
balance and comfort.
Let the guard (9) rest on the ground.

Slacken the handle knob (5).

Move the handle into the desired position.

Securely tighten the handle knob.

7