Siemens SN series Operating Instructions Manual
Siemens SN series Operating Instructions Manual

Siemens SN series Operating Instructions Manual

Hide thumbs Also See for SN series:
Table of Contents




Table of Contents

Summary of Contents for Siemens SN series

  • Page 1 SN… SX…...
  • Page 3: Table Of Contents

    Table of contents Loading the dishwasher ..13 Intended use ....4 Unloading the dishwasher ..14 Cups and glasses .
  • Page 4: Intended Use

    Intended use Interrupting the programme ..24 Intended use Terminating the programme ..25 Changing the programme..25 I n t e n d e d u s e This appliance is intended for Intensive drying.
  • Page 5: Delivery

    Safety instructions Delivery The electrical connection conditions must correspond 1. Check the packaging and with the specifications dishwasher immediately for on the dishwasher rating plate 9B. damage caused in transit. Do not switch on a damaged If the power cord of this appliance, but contact your appliance is damaged, supplier.
  • Page 6: In Daily Use

    Safety instructions If you cannot obtain any In daily use information from Read and observe the safety the manufacturer, you must information and instructions not install the dishwasher for use on the packaging above or below these for cleaning and rinsing agents. appliances.
  • Page 7 Safety instructions Warning Warning Risk of injury! Risk of scalding! Open the door carefully when To prevent injuries, e.g. the programme is still running. caused by stumbling, open There is a risk of hot water the dishwasher only briefly spraying out of the appliance. in order to load and unload the dishwasher.
  • Page 8: Protection Of The Environment

    Protection of the environment When opening and closing Protection of the the door on an eye-level environment appliance, ensure that children do not become i o n P r o t e c t o f t e n v i r o n m e n t jammed or crushed between Both the packaging of new appliances and the old appliances themselves...
  • Page 9: Getting To Know Your Appliance

    Getting to know your appliance Appliance interior Getting to know your appliance 1" Interior light * G e t t i t o k n o w y o u r a p p l i a n c 1* Cutlery drawer Diagrams of the control panel 12 Top basket and the interior of the appliance can be...
  • Page 10: Water Softening System/Special Salt

    Water softening system/Special salt To change the setting: Water softening 1. Press programme button 3. system/Special salt Each time the button is pressed, the set value increases by one level; W a t e r s o f t e n i s y s t e m / S p e c i s a l t when the value of :...
  • Page 11: Using Special Salt

    Water softening system/Special salt Using special salt Using detergents with salt component D e t e r g e n t s w i t h s a l t c o m p o n e n t Always refill with special salt immediately before switching on the If combined detergents with a salt appliance.
  • Page 12: Rinse Aid

    Rinse aid 2. Carefully pour rinse aid up Rinse aid to the max. mark in the filler opening. R i n s e a i d As soon as the rinse-aid refill indicator P is lit on the fascia, there is still a rinse-aid reserve of 1-2 rinsing processes.
  • Page 13: Switching Off Rinse Aid Refill Indicator

    Utensils To change the setting: Glass and utensil damage 1. Press programme button 3. Causes: Each time the button is pressed, the set value increases by one level; Glass type and glass production when the value of : has been process.
  • Page 14: Unloading The Dishwasher

    Utensils Unloading the dishwasher Pans Bottom basket 9" To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
  • Page 15: Cutlery Drawer

    Utensils Cutlery drawer F olding spikes * F o l d i n g s p i k e s Arrange the cutlery in the cutlery drawer * depending on model 1* as illustrated. Separately arranged The spikes can be folded down to utensils are easier to remove after improve arrangement of pans, bowls washing.
  • Page 16: Adjusting The Height Of The Basket

    Detergent Adjusting the height of the 3. To raise the basket, hold the basket on the sides of the upper edge and basket lift it up. 4. Before re-inserting the basket again, The height of the upper utensils basket ensure that it is at the same height 12 can be adjusted in 3 stages to on both sides.
  • Page 17: Adding Detergent

    Detergent Adding detergent If the utensils are only lightly soiled, 1. If the detergent dispenser 92 is still slightly less than the indicated amount closed, press the lock 9: to open of detergent is usually adequate. the detergent dispenser. Suitable detergents and care products Pour detergent into the dry detergent can be purchased online dispenser 92 only (insert tablet flat,...
  • Page 18 Detergent Warning – Do not place small parts Notes for washing in the tablet collecting tray You will obtain optimum rinsing 1B; this prevents the tablet from and drying results by using solo dissolving evenly. detergents and applying salt and rinse aid separately. Warning –...
  • Page 19: Overview Of Programmes

    Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
  • Page 20: Programme Selection

    Additional options Programme selection Additional options o n a l A d d i t i o p t i o n s You can select a suitable programme according to the type of utensils and * depending on model degree of soiling.
  • Page 21: Intensive Zone

    Operating the appliance Ï Intensive zone * A qua sensor * I n t e n s i v e z o n e A q u a s e n s o r Perfect for a mixed load. You can wash * depending on model very soiled pots and pans in the lower The Aqua sensor is an optical...
  • Page 22: Switching On The Appliance

    Operating the appliance Warning – Risk of injury! Optical display while Do not touch the blow opening 1R. The the programme is running * O p t i c a l d i s p l a y w h i l e t h e p r o g r a m m e i s r u n n i n g blow opening becomes hot and, furthermore, any damage will result in * depending on model...
  • Page 23: Remaining Running Time Display

    Operating the appliance 6. To delete timer programming `, 6. Keep pressing programme button 3 until the required value, press the + or – button until indicated on the digital display X. e.g. : , is indicated on the digital display 8.
  • Page 24: Automatic Switch Off

    Operating the appliance Note To change the setting: 1. Press programme button 3. Depending on the setting for “Automatic switch off when programme ends or Each time the button is pressed, interior light”, the optical display is no the set value increases by one level; longer or only briefly visible.
  • Page 25: Terminating The Programme

    Cleaning and maintenance 3. To continue the programme, switch Intensive drying on the ON/OFF switch ( again. 4. Close the door. The final rinse uses a higher temperature which improves the drying result. The running time may increase T erminating the programme slightly.
  • Page 26: Overall Condition Of The Machine

    Cleaning and maintenance Overall condition Filters of the machine The filters 1j keep large foreign objects in the rinsing water away from Check spray arm for grease the pump. These foreign objects may and limescale deposits. occasionally block the filters. If you find such deposits: The filter system consists of a coarse Fill detergent dispenser with...
  • Page 27: Spray Arms

    Fault, what to do? Spray arms Fault, what to do? F a u l t , w h a t d o ? Limescale and contaminants in the rinsing water may block nozzles and Experience has shown that you can bearings on the spray arms 1: and rectify most faults which occur in daily operation yourself.
  • Page 28: Waste Water Pump

    Fault, what to do? Waste water pump 6. Check impeller wheel and remove any foreign objects. 7. Place cover in the original position Large food remnants or foreign objects and press down until it engages which were not captured by the filters (click).
  • Page 29: Fault Table

    Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display @ lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min.
  • Page 30 Fault, what to do? Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON/OFF switch (. After a short time restart indicated on the digital occurred. display. the appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
  • Page 31 Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid Refill rinse aid. in the dispenser. Programme selected without Select programme with drying (see drying. Overview of programmes, Programme sequence). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
  • Page 32 Fault, what to do? Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
  • Page 33 Fault, what to do? Fault Cause Remedial action Water stains on plastic Droplet formation on plastic Use a more intensive programme (more parts surface is physically unavoidable. water changes). After drying, water stains are Arrange utensils in a sloping position. visible.
  • Page 34 Fault, what to do? Fault Cause Remedial action Coloured (blue, yellow, Film formation consisting Can be partly removed with machine brown), difficult to remove of ingredients from vegetables cleaner or by mechanical cleaning. Coatings to non-removable coatings (e.g. cabbage, celery, potatoes, are harmless.
  • Page 35 Fault, what to do? Fault Cause Remedial action Rust spots on the cutlery. Cutlery not adequately rust- Use corrosion-resistant cutlery. resistant. Knife blades are frequently more severely affected. Cutlery will also rust if rusting Do not wash rusting parts. parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.).
  • Page 36 Fault, what to do? Fault Cause Remedial action Appliance stops Door not closed properly. Close the door. in the programme or Do not place utensils or fragrance Check whether rear panel is being pressed programme is interrupted. dispenser in the tablet collecting in, e.g.
  • Page 37: Customer Service

    Customer service Customer service Installation and connection C u s t o m e r s e r v i c e If you are unable to rectify the fault, l a t i o n I n s t a l a n d c o n n e c t i please contact your customer service.
  • Page 38: Delivery

    Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance with the aid of the small water stains.
  • Page 39: Drinking Water Connection

    Installation and connection Drinking water connection Setting hot water: 1. Open the door. 2. Switch on ON/OFF switch (. 1. Fasten the drinking water connection to the tap according 3. Hold down programme button # to the installation instructions using and press START button )"...
  • Page 40: Removing The Appliance

    Installation and connection A power cord extension may be Transportation purchased from customer service only. Empty the dishwasher and secure loose Use only a residual current operated parts. circuit-breaker which features Drain the appliance according to the the symbol ‚. Only this extension following steps: guarantees compliance with 1.
  • Page 42 *9000786191* 9000786191 en (9311) 640TV...

This manual is also suitable for:

Sx series

Table of Contents