Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Siemens SN678D01TG
Summary of Contents for Siemens SN678D01TG
- Page 1 Dishwasher SN.../SX... en Instruction manual...
-
Page 3: Table Of Contents
Table of contents e n I n s t r u c t i o n m a n u a l Intended use ....5 Utensils. - Page 4 Operating the appliance ..30 Customer service ... .49 Programme data ....30 Installation and connection.
-
Page 5: Intended Use
Intended use en Keep children below the age of Intended use 8 years old at a safe distance from the appliance and power This appliance is intended ■ cable. I n t e n d e d u s e for use in the home and domestic environments. -
Page 6: Installation
en Safety instructions Also follow the installation Installation ■ instructions for the Following installation, ensure dishwasher to ensure that all ■ that the back of the appliances are operated dishwasher is not freely safely. accessible (protection If there is no information or if ■... -
Page 7: In Daily Use
Safety instructions en Please note that the Damage ■ insulation material of the The appliance may be dishwasher power cord may ■ repaired and opened up by a melt next to heat sources technician only. To do this, (e.g. heating / hot water disconnect the appliance installations) or hot from the power supply. - Page 8 en Safety instructions Warning Warning Risk of injury! Risk of explosion! To prevent injuries, e.g. Do not add any solvents to the ■ caused by stumbling, open rinsing compartment. Danger of the dishwasher only briefly in explosion! order to load and unload the Warning dishwasher.
-
Page 9: Door Lock
Safety instructions en Ensure that children do not Activate the child-proof lock ■ place fingers in the tablet (door lock) as follows: collecting tray 1B. Small Pull the catch of the fingers could become caught child-proof lock towards in the slots. yourself (1). -
Page 10: Environmental Protection
en Environmental protection Deactivate the child-proof lock Environmental (door lock) as follows: protection Press the catch of the child-proof lock to the right Both the packaging of new appliances (1). t e c t i o n E n v i r o n m e n t a l p r o and the old appliances themselves Press the catch of the contain valuable raw materials and... -
Page 11: Getting To Know Your
Getting to know your appliance en Appliance interior Getting to know your See Fig. ~ Page 2 appliance 1" Interior light * 1* Cutlery drawer * Diagrams of the control panel and the y o u r a p p l i a n c e G e t t i n g t o k n o w 12 Top basket interior of the appliance can be found at... -
Page 12: Info Button
en Getting to know your appliance Info button { Time setting The Info button { can be used to When the appliance is switched on the I n f o b u t t o n T i m e s e t t i n g display additional programme for the first time, the time starts at 12:00 information. -
Page 13: Switching On The Appliance For The First Time
Getting to know your appliance en Switching on the appliance for the first time When the dishwasher is switched on for Change the setting as follows: the first time, you are taken directly to Keep pressing button > )* until the the settings for switching on the required setting is displayed. -
Page 14: Settings
en Getting to know your appliance Settings The dishwasher has been preset with Make the setting with setting buttons certain settings for your convenience. + - X. You can change this factory setting. Press and hold the Info button { 8 for 3 seconds. -
Page 15: Water Softening System
Water softening system/special salt en Setting Factory setting Infotext by pressing Info button { Timelight * While programme is running, status information is projected onto floor. Infolight * Light is projected to signal an active cleaning cycle. Start programme Eco 50° When switching on, the last selected programme appears. -
Page 16: Adjusting The Water Softening System
en Water softening system/special salt Adjusting the water softening Using special salt system As soon as the low salt indicator P is lit on the control panel or is requested The amount of salt dispensed can be on the front display * ):, salt should set from 0 to 62°E. -
Page 17: Detergent With A Salt Component
Rinse aid en Using detergents with salt Rinse aid component If combined detergents with a salt As soon as the low rinse-aid indicator s a l t c o m p o n e n t D e t e r g e n t w i t h a component are used, special salt can R i n s e a i d H is lit on the control panel or is... -
Page 18: Setting Amount Of Rinse Aid
en Rinse aid Add rinse-aid up to the max. mark. Set the amount of rinse aid as follows: Open the door. Switch on ON/OFF switch (. Press Info button { 8 for 3 seconds until the following text is indicated on the display window at the top @: Scroll with <... -
Page 19: Utensils
Utensils en Loading the dishwasher Utensils Remove large food remnants. It Not suitable is not necessary to prerinse utensils U t e n s i l s under running water. Cutlery and utensils made of wood. Place the utensils so that ■... -
Page 20: Lower Basket
en Utensils Utensils must not be placed Heavily soiled utensils (pans) Note: Tip: above the tablet collecting tray 1B. should be placed in the lower basket. These may block the lid of the detergent The more powerful spray jet provides a dispenser and prevent it from opening better dishwashing result. -
Page 21: Etagere
Utensils en Etagere * You can take out the cutlery drawer. The etagere and the space underneath E t a g e r e can be used for small cups and glasses or for larger items of cutlery, such as wooden spoons or serving cutlery. -
Page 22: Folding Spikes
en Utensils Folding spikes * Knife rack * * Depending on the features of your * Depending on the features of your F o l d i n g s p i k e s K n i f e r a c k dishwasher, the spikes can be folded dishwasher, the upper basket is fitted down. -
Page 23: Baking Sheet Spray Head
Utensils en Baking sheet spray head * Unloading the dishwasher * depending on the features of your To prevent water from dripping off the y h e a d B a k i n g s h e e t s p r a dishwasher upper basket onto the utensils in the Large trays or grilles as well as large... - Page 24 en Utensils Upper basket with side levers Appliance height 86.5 cm With cutlery basket Upper Lower Pull out upper basket 12. basket basket Hold the sides of the basket along Setting 1 max. ø 24 cm 34 cm the upper edge. This prevents it from suddenly Setting 2 max.
-
Page 25: Detergent
detergent en Adding detergent Detergent If the detergent dispenser 9: is still You can use tablets as well as powder closed, actuate locking bar 9B to d e t e r g e n t or liquid detergents for dishwashers, but open it. -
Page 26: Combination Detergent
en detergent If the utensils are only lightly You will obtain optimum rinsing and Tip: ■ soiled, slightly less than the indicated drying results by using solo amount of detergent is usually detergents and applying salt adequate. and rinse aid separately. Suitable detergents and care products If programmes are short, tablets may ■... -
Page 27: Overview Of Programmes
Overview of programmes en Overview of programmes The max. possible number of programmes is illustrated in this overview. The a m m e s O v e r v i e w o f p r o g r corresponding programmes and their arrangement can be found on the fascia. Type of dish Type of soiling Programme... -
Page 28: Programme Selection
en Overview of programmes Type of dish Type of soiling Programme Possible Programme sequence additional options Time-optimised: u / t / part dried, common Cleaning 65° mixed utensils household food Intermediate rinse and cutlery remnants Rinsing Short 60°C Drying sensitive Time-optimised: ñ... -
Page 29: Additional Functions
Additional functions en Ï intensiveZone * Additional functions Perfect for a mixed load. You can wash i n t e n s i v e Z o n e very soiled pots and pans in the lower * Depending on the features of your i o n s A d d i t i o n a l f u n c t basket together with normally soiled... -
Page 30: Operating The Appliance
en Operating the appliance If you change several settings, first Tip: Operating the make all changes in succession. Now press the Info button { 8 for appliance 3 seconds. This saves all set values in the appliance. Programme data p l i a n c e O p e r a t i n g t h e a p AquaSensor * The programme data (consumption... -
Page 31: Zeolith Drying
Operating the appliance en ¼ Sensor setting Zeolith drying Warning The programme sequence is optmised Z e o l i t h d r y i n g in Auto programmes with the aid of Risk of burns from touching the blow sensors. -
Page 32: Autopoweroff
en Operating the appliance AutoPowerOff (Switching off TimeLight (Optical display automatically after the end of while the programme is the programme) running) * To save energy, the dishwasher * depending on the features of your A u t o P o w e r O f f t i m e L i g h t is switched off 1 minute after dishwasher... -
Page 33: Button Volume
Operating the appliance en Button volume Switching the appliance on When you are operating the dishwasher, Turn on tap fully. a signal sounds whenever a button is Open the door. pressed. You can control the volume of Switch on ON/OFF switch (. the signal. -
Page 34: Time Preselection
en Operating the appliance Time preselection Switching off the appliance You can delay the start of the Short time after the end of the programme by up to 24 hours. programme: Depending on the setting of the time Open the door. display, the end of programme is Switch off ON/OFF switch (. -
Page 35: Terminating The Programme
Cleaning and maintenance en Terminating the programme Cleaning and (Reset) maintenance Open the door. p r o g r a m m e T e r m i n a t i n g t h e Press the START button )" and A regular inspection and maintenance hold for 3 seconds t e n a n c e... -
Page 36: Machine Care
en Cleaning and maintenance ‰ Notes Machine Care Only clean the appliance with ■ Machine Care used in combination with special detergents/appliance M a c h i n e C a r e commercially available machine cleaners which are suitable for use cleaning detergent is a suitable with dishwashers. -
Page 37: Special Salt And Rinse Aid
Cleaning and maintenance en Filters Notes Remove any coarse soiling in the ■ The filters 1j keep large foreign interior using a damp cloth. objects in the rinsing water away from Run the programme without dishes, ■ the pump. hese foreign objects may and in combination with a machine occasionally block the filters. -
Page 38: Spray Arms
en Fault, what to do? Spray arms Fault, what to do? Limescale and contaminants in the rinsing water may block nozzles and Experience has shown that you can F a u l t , w h a t t o d bearings on the spray arms 1: and rectify most faults which occur in daily operation yourself. -
Page 39: Waste Water Pump
Fault, what to do? en Waste water pump Check impeller wheel and remove any foreign objects. Large food remnants or foreign objects Place pump cover in the original which were not captured by the filters position (2) and press down until it may block the waste water pump. -
Page 40: Fault Table
en Fault, what to do? Fault table Fault Cause Remedial action Error code “:‚‰ is lit. Supply hose kinked. Install supply hose without kinks. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. - Page 41 Fault, what to do? en Fault Cause Remedial action Error code “:ƒ† is lit. Waste water pump blocked or Clean pump and lock cover correctly. cover on the waste water pump is ~ "Waste water pump" on page 39 not locked in position. Error code “:ƒˆ...
- Page 42 en Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the Refill rinse aid. dispenser. Programme selected without Select programme with drying. drying. ~ "Overview of programmes" on page 27 Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
- Page 43 Fault, what to do? en Fault Cause Remedial action Food remnants on the Utensils placed too closely Arrange utensils with adequate clearance utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
- Page 44 en Fault, what to do? Fault Cause Remedial action Detergent residue. Detergent dispenser cover 9: Utensils must not be placed above the blocked by utensils and therefore tablet collecting tray 1B. These may does not open fully. block the lid of the detergent dispenser and prevent it from opening fully.
- Page 45 Fault, what to do? en Fault Cause Remedial action White, stubborn coatings; Detergent substances are Change detergent brand. limescale on the utensils, deposited. These coatings cannot Clean appliance mechanically. container or door. usually be removed with chemicals (appliance cleaner, ...). Hardness range incorrectly set or Set water softening system according to water hardness greater than 8.9...
- Page 46 en Fault, what to do? Fault Cause Remedial action Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing temperature. Utensils precleaned too intensely; Do not prerinse utensils. Remove only sensors therefore decide on large food remnants. weak programme sequence. Increase sensitivity of the sensors.
- Page 47 Fault, what to do? en Fault Cause Remedial action Appliance cannot be Malfunction. Disconnect appliance from the power switched on or operated. supply; pull out the mains plug or switch off the fuse. Wait at least 5 seconds, then connect the appliance to the power supply.
- Page 48 en Fault, what to do? Fault Cause Remedial action Detergent residue in the Spray arms blocked by utensils, Ensure that the spray arms can rotate detergent dispenser 9: therefore detergent is not rinsed freely. or in the tablet collecting out. tray 1B.
-
Page 49: Customer Service
Customer service en Customer service Installation and connection If you are unable to rectify the fault, C u s t o m e r s e r v i c e please contact your customer service. The dishwasher must be connected We will always find an appropriate c o n n e c t i o n I n s t a l l a t i o n a n d... -
Page 50: Contents Of Package
en Installation and connection Contents of package Technical specifications If you have any complaints, contact the Weight: ■ dealer from whom you purchased the up to 60 kg appliance or our customer services. Voltage: ■ 220–240 V, 50 Hz or 60 Hz Dishwasher ■... -
Page 51: Installation
Installation and connection en Installation Drainage connection The required installation dimensions The required work sequence can be can be found in the installation found in the installation instructions. instructions. Level the appliance with If required, fit a siphon with an the aid of the height-adjustable feet. -
Page 52: Drinking Water Connection
en Installation and connection Drinking water connection Warm water connection * * depending on the features of your Fasten the drinking water connection i o n W a r m w a t e r c o n n e c t dishwasher to the tap according The dishwasher can be connected... -
Page 53: Electrical Connection
Installation and connection en Electrical connection Removal Connect the appliance to an Also observe ■ alternating current only, ranging from the sequence of worksteps here. 220 V to 240 V and 50 Hz or 60 Hz Disconnect the appliance from the via a correctly installed socket with power supply. -
Page 54: Transporting
en Installation and connection Transporting Protection against frost If the appliance is in a room where there Empty the dishwasher and secure loose n g t h e a p p l i a n c e ) s t f r o s t ( E m p t y i P r o t e c t i o n a g a i n is a risk of frost (e.g. - Page 56 *9001257028* 9001257028 (9611) 642 TW...