JAI GO-5000M-PGE User Manual page 65

Acquisition mode
Acquisition
Trigger Selector Exposure
Transfer
Exposure mode
Trigger option
Trigger Overlap
Trigger Input Signal
Opt. Filter
Timed
Exposure
Mode
Trigger Width
Exposure Auto
Auto Exposure Response Speed
Video Send mode
Digital I/O
Ref. level
Black
Video level adj. range
Level
Adj. range
Adjust.
Resolution
Analog Base Gain (For manual)
Manual
Adj. range
Gain Auto
Gain
WB Gain
Control
WB Area
WB Range
White Balance
Detection
Blemish
Compensation
Comp.
Numbers
ALC
Gamma
Dark compression
LUT
HDR
6-Pin
Connector
Power
PoE
Lens mount
GO-5000M-PGE / GO-5000C-PGE
Continuous / Single Frame / Multi Frame (1 ～255)
Acquisition Start/ Acquisition Stop
Frame Start
JAI Frame Transfer
OFF, Continuous, Timed (EPS), Trigger Width
OFF / RCT (with ALC function)
Fixed (Readout)
Line 6 (Opt In), Software, PG0, NAND Out 0/1, Action 1/2
5 steps (10 µs (Typ), 100 µs, 500 µs, 1ms, 5ms, 10ms)
Exposure Auto: OFF 10 μs (Min.)～ 8 second (Max.) (Note1), Variable unit:
Exposure Auto: Continuous 10 µs (Min.)～ 8 second (Max.)( Note1),
Normal ROI, Multi ROI (1 to 5), Trigger sequence, Command sequence,
0dB ～+24dB (Note2)
1 step=x0.01 (0.005dB to 0.08dB)
Varies by setting value
Complement by adjacent pixels (Continuous blemishes are not compensated)
AGC and auto exposure can be combined and automatically controlled
OFF: γ=1.0, ON=32 points (Mono), 16 points (Bayer) can be set
4 settings, Level 1, 2, 3 and 4
Input range
Current
Power
Input range
Current
Power
Variable unit: 1 μs
10 μs (Min.Note1) ～ ∞ (Max.) (Note1)
OFF / Continuous
Delayed readout
Line Selector (6P): GPIO IN / GPIO OUT
33.5LSB 10-bit (Average value of 100*100)
0 ～ 100 10-bit
±64LSB against Ref. level 10-bit
1 STEP = 0.25LSB
0dB, 6dB, 12dB
OFF / Continuous
—
—
—
—
Detect white blemish above the threshold value
(Black blemish is detected only by factory )
0.45, 0.6 and 1.0 (OFF) (3 steps are available)
Choice of Linear or Dark compression ON
DC+12V to +24V ± 10% (At the input terminal)
190mA ± 20mA (At 12V input, Full pixels) (Typical)
2.5W (At 12V input, Full pixels) (Typical)
DC 35 ～ 57V
58mA ±6mA (At 55V input, Full pixels) (Typical)
3.0W (At 12V input, Full pixels) (Typical)
C mount Rear protrusion of the lens is less than 10 mm
- 63 -
1 μs
1 ～ 8
0dB, 6dB, 12dB (R/G/B individual setting)
0dB ～+24dB (Note2)
1 step=x0.01 (0.005dB to 0.08dB)
Varies by setting value
OFF / Continuous
R / B : -7dB to +15dB, 1 step = 0.01dB
4 x 4
3000K ～ 9000K
OFF, Continuous, Once
256 pixels
—