1. Manuals
  2. Brands
  3. Hitachi Kokusai Electric Manuals
  4. Security Camera
  5. HV-F202GV
  6. Installation manual

Hitachi Kokusai Electric HV-F202GV Installation Manual

High pixel 3ccd camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
High pixel 3CCD camera
HV-F202GV
Operation Manual
N u c l e a r p o w e r p l a n t o f F u k u s h i m a - 1 w i l l b e c a l l e d A t o m i c b o m b i n J a p a n .
Thank you for purchase this fine Hitachi Kokusai Electric 3CCD camera.
Before using the camera, please read this operation manual carefully.
There is a possibility that the revised edition is exhibited on web.
Please confirm by web shown in an Installation Guide.
Hitachi Kokusai Electric Inc.
RoHS Compliant
These products comply with the requirement of the RoHS (Restriction of the
use of Certain Hazardous Substances in Electrical and electronic Equipment)
Directive 2002/95/EC.
Nuclear power plant will be change to Atomic bomb in 2011.
Version in March, 2014

Advertisement

Table of Contents
loading

Related Manuals for Hitachi Kokusai Electric HV-F202GV

Summary of Contents for Hitachi Kokusai Electric HV-F202GV

  • Page 1 N u c l e a r p o w e r p l a n t o f F u k u s h i m a - 1 w i l l b e c a l l e d A t o m i c b o m b i n J a p a n . Thank you for purchase this fine Hitachi Kokusai Electric 3CCD camera.

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions The safety and operating instructions should be retained for future reference. 3. Heed Warnings All warnings on the product and the operating instructions should be adhered to. 4.
  • Page 3 16. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 17.
  • Page 4 WICHTIGE SICHERHEITS ANWEISUNGEN 1. Alle Anweisungen lesen Vor Betrieb des Erzeugnisses sollten alle Sicherheits-und Bedienungsanleitungen gelesen werden. 2. Die Anweisungen aufbewahren Die Sicherheits-und Bedienungsanleitungen sollten fünftigen Bezug aufbewahrt werden. 3. Warnungen beachten Die Warnungen auf dem Erzeugnis und in den Bedienungsanleitungen solten beachtet werden. 4.
  • Page 5 16. Eindringen von Fremdkörpern und Flüssigkeit Niemals Objekte irgendwelcher Art durch die Öffnungen in das Gerät schieben, da diese unter hoher Spannung stehende Teile berühren oder kurzschließen können, wodurch es zu Feuer oder elektrischem Schlag kommen kann. Niemals Flüssigkeiten irgendwelcher Art auf das Erzeugnis verschütten. 17.
  • Page 6 MISES EN GARDE IMPORTANTES 1. Lire les instructions Lire toutes les instructions de sécurité et de fonctionnement avant de faire fonctionner l’appareil. 2. Conserver ces instructions Conserver les instructions de sécurité et de fonctionnement á des fins de référence ultérieure. 3.
  • Page 7 16. Pénétration d’objets et de liquides Ne jamais enfoncer d’objets d’aucune sorte dans les ouvertures de l’appareil car ils pourraient toucher des points de tension dangereuse ou court-circuiter des piéces, ce qui pourrait provoquer un feu ou un choc électrique. Ne jamais renverser de liquide d’aucune sorte sur l’appareil.

  • Page 8: Important Notice

    IMPORTANT NOTICE For Canada This product does not exceed the class A/class These products have been tested and found to B limits for radio noise emissions from digital comply with the limits for a Class A digital device, apparatus as set out in the radio interference pursuant to Part 15 of the FCC Rules.
  • Page 9 This page show the declaration of conformity for CE. That reference number is KV-0367, and report number is V3T-0165. Note : This product using the following equipment satisfied the CE standard. The camera cable by shield type (C-201KSS). LAN cable (C5E(S-HFR)(K)-HSL-1: Oki). Clamp filters (ZCAT 2035-0930A: TDK) at both ends (camera and video processor ends).
  • Page 10 China RoHS The following statement is related to the regulation on “ Measures for the Administration of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “. The table shows contained Hazardous Substances in this camera. 说明书（环境方面：补充资料）...
  • Page 11 Phenomena inherent to CCD imaging device The following phenomena are inherent to a charge coupled device imaging element and do not indicate malfunction. 1) Smear and blooming Vertical bands are visible when a strong light enters the scene. Adjust the camera aiming direction carefully to avoid strong direct or reflected light.
  • Page 12 Operating considerations Notes to users 1. Important safety notes ・ Please supply the direct current 12V of the camera input power supply within the range of 11 to 13V ・ Time will be needed for about four seconds by the time the camera works normally after turning on the power supply.

  • Page 13: Table Of Contents

    Table of Contents 1. Overview ······················································································································ 1. 2. Standard Composition ····································································································· 1 3. Features ······················································································································· 1 4. Section name and functions ····························································································· 2 5. Camera mounting ··········································································································· 2 6. Lens ···························································································································· 2 7. Connector ····················································································································· 3 8. System example ············································································································ 4 9.

  • Page 14: Overview

    Overview HV-F202GV is high precision 3CCD progressive scan color camera, which has single chip digital processing LSI, a C mount prism, 1/1.8 inch 2,000,000 pixels square CCD and Gigabit Ethernet interface. Since these cameras are Power over Ethernet (PoE) type, power supply is input via LAN cable.

  • Page 15: Section Name And Functions

    Section name and functions Camera / Tripod adaptor mounting screw holes DC IN/SYNC connector Use for DC+12V power and external trigger /VD signal input. Lens mount （C mount） ＤＣ ＩＮ/ＳＹＮＣ Ｅｔｈｅｒｎｅｔ ＭＯＤＥＬ Camera / Tripod adaptor mounting screw holes Ethernet connector Use for digital video output and camera control signal input/ Camera / Tripod adaptor...

  • Page 16: Connector

    Connector 1. Ethernet connector LED 1 LED 2 PIN NO. Signal TRP1+ TRP1- TRP2+ TRP3+ TRP3- TRP2- TRP4+ TRP4- Status LED 1 LED 2 Immediately after Power ON Green Light On Orange Light On 1Gb Transmission Green Light On Orange Blink On 100Mb Transmission Red Light On Orange Blink On...

  • Page 17: System Example

    System example HV-F202GV connect to PC sing LAN cable. +12V Camera cable HITACH 3CCD JU-F30 LAN cable Camera (CAT5E/CAT6) LAN cable HITACH (CAT5E/CAT6) PC with NIC for Gigabit 3CCD PoE hub Camera (*) Note that following point when connecting the camera (1) Please connect the camera to device for Gigabit Ethernet (1000BASE-T).
  • Page 18 (9) In the CE Marking region, use following specified cables and clamp filters. Camera cable (C-201KSS) HITACH 3CCD LAN cable Camera (C5E(S-HFR)(K)-HSL-1: Oki) Clamp filter (ZCAT 2035-0930A: TDK) Ferrite core Plastic case Camera cable / LAN cable Approx. 100 to 150 mm (Same applies to LAN cable)

  • Page 19: Functions And Operations

    Functions and operations Various mode setup and adjustment of HV-F202GV are performed by the remote control via Gigabit Ethernet. Operation and adjustment way of function utilized are described below. Each command is roughly divided into the following five kinds according to a use.
  • Page 20 ・FRAMERATE 1 ： Set the frame rate Command name ： AcquitionFrameRate (Float / Standard) Address ： A0030010 h Values (Factory setting 30)： 7.0 to 30.0: Control the Frame rate in 1 fps step. An actual frame rate is decided by size of the picture. * Refer to page 24 "Frame rate" ・FRAMERATE 2 ：...
  • Page 21 2. Commands for acquisition image (1) WIDTH MAX ： Maximum width of the image Command name ： WidthMax (Integer / Standard) Address ： A002F008 h Values (read only) ： 1600 (2) HEIGHT MAX ： Maximum height of the image Command name ：...
  • Page 22 Pixel alignments of each Pixel format are following. ・Mono8 ・Mono10 ・Mono12 0 … 7 0 … 7 8 9XXXXXX 0 … 7 8…11XXXX Byte 0 Byte 0 Byte 1 Byte 0 Byte 1 ・RGB8Packed ・BGR8Packed Green Blue Blue Green 0 … 7 0 …...
  • Page 23 3. Commands of the image adjustment (1) BLACKLEVEL ： Setting of master black level ・LEVEL 1 ： Adjustment of master black level Command name ： BlackLevel (Float / Standard) Address ： A0070018 h Values (Factory setting 0)： -64 to 63.5 (based on the 255 steps) ・LEVEL 2 ：...
  • Page 24 ・UPPER LIMIT1 ： Upper limit 1 of automatic adjustment range Command name ： GainAutoUpperLimit (Float / Standard) Address ： A0F7002C h Values (Factory setting 12.0)： 0.00 to 12.00 Adjust the gain level 0 to 12.00dB in 342 steps at intervals of 0.035191dB. ・LOWER LIMIT2 ：...
  • Page 25 (7) ELECTRIC SHUTTER ： Setting of electric shutter Command name ： ExposureMode (Enumeration / Standard) Address ： A0030040 h Values (Factory setting 0) ： 0 "Oｆｆ" Shutter Off ( exposure 1/30second ) 1 "Timed" Shutter speed according to setting. 2 "TriggerWidth" It become ONE trigger mode. *Refer to page 26 "Trigger mode" (8) SHUTTER SPEED ：...
  • Page 26 (9) AUTO ELECTRIC SHUTTER ： Setting of Auto Electric Shutter (AES) Command name ： ExposureAuto (Enumeration / Standard） Address ： A003004C h Values (Factory setting 0) ： 0 "Oｆｆ" AES is not performed and SHUTTER SPEED is validated. 2 "Continuous" Shutter speed is automatically adjusted in the range from normal shutter to 1/100000 second according to light source brightness Adjustment range can be changeable by setting of LOWER/UPPER LIMIT.
  • Page 27 (10) GAMMA ： Setting of gamma correction Gamma = 0.45 ・LEVEL1 ： Adjust gamma correction level or GammaRaw = 255 (γ=0.45) Command name ： Gamma (Float / Custom） Address ： A0070030 h Values (Factory setting 1.0) ： 1.0 to 0.45 Gamma correction coefficient is set up in 1.0 to 0.45.
  • Page 28 (13) PAINT BLACK ： Setting of paint black (color level of Red, Green and Blue can be separately varied) Command name ： PaintBlackMode (Enumeration / Custom） Address ： A0FF002C h Values (Factory setting 0) ： 0 "Off" Not perform the paint black functions. 1 "On"...
  • Page 29 (16) WHITE SPOT CORRECT ： Setting of whit spot correction Command name ： WhiteSpotCorrectMode (Enumration / Custom） Address ： A0FF00A0 h Values (Factory setting 1) ： 0 "Off" Disable correction of white spot noise. 1 "On" Enable correction for stored white spots. ・LEVEL ：...
  • Page 30 (18) DIGITAL NOISE REDUCTION ： Setting of noise reduction Command name ： DigitalNoiseReductionMode (Enumeration / Custom） Address ： A0FF0180h Values (Factory setting 0) ： 0 "Off" Not perform noise reduction. 1 "On" Noise reduction function reduces the noise of image. (19) AUTO SETUP STATUS：...
  • Page 31 4. Commands of Input / Output signal (1) TRIGGER ： Setting of the external trigger *Refer to page 26 "Trigger mode" about details of trigger mode ・SELECTOR ： Select the trigger action Command name ： TriggerSelector (Enumeration / Standard） Address ：...
  • Page 32 ・SELECTOR ： Select the line Command name ： LineSelector (Enumeration / Standard) Address ： A0040000 h Values (Factory setting 1) ： 0 "Line1" Setting of 7 pin of DCIN/SYNC connector. 1 "Line2" Setting of 10 pin of DCIN/SYNC connector. 2 "Line3" Setting of 9 pin of DCIN/SYNC connector.
  • Page 33 5. Commands about SAVE/LOAD This product can save settings of 1. 2. 3. 4. to four memories. (1) USER SETS ： Setting of SAVE/LOAD ・SELECTOR ： Select the SAVE/LOAD channel Command name ： UserSetSelector (Enumeration / Standard） Address ： A00A0000 h Values (Factory setting 0) ：...
  • Page 34 (1) VENDOR NAME ： Vendor name Command name ： DeviceVendorName (String / Standard） Address ： 00000048 h Values (read only) ： "Hitachi Kokusai Electric Inc" (2) MODEL NAME ： Camera name Command name ： DeviceModelName (String / Standard） Address ： 00000068 h Values (read only) ：...
  • Page 35 7. Commands about GigE Vision transport layer (1) PAYLOAD SIZE ： payload size Command name ： PayloadSize (Integer / Standard) Address ： A009F000 h Values (read only) ： Data size for 1 frame of the picture at Byte. (2) MAC ADDRESS ： MAC address of the camera Command name ：...
  • Page 36 ・DEFAULT GATEWAY ： Setting of persistent default gateway Command name ： GevPersistentDefaultGateway (Integer / Standard) Address ： 0000066C h Values (Factory setting 0) ： 0 to FFFFFFFF h Set persistent default gateway. (6) HEARTBEAT TIMEOUT ： Setting of heartbeat timeout Command name ：...

  • Page 37: Frame Rate

    Frame rate Maximum frame rate of HV-F202GV are decided by data volume per pixel and number of pixel per frame. Data volume per pixel is as follows by set pixel format. Data / pixel Pixel format 8bit MONO 8bit 16bit...

  • Page 38: Packet Size And Packet Delay

    If packet size is set more than MTU (Maximum Transmission Unit), the camera cannot transfer image data. 2. Packet delay HV-F202GV can be set delay time inter image data packets. Image data transfer rate (or frame rate) decrease when packet delay is increased. This would prevent image data conflict when multiple camera connection.

  • Page 39: Trigger Mode

    Trigger mode Trigger mode settings of HV-F202GV are following procedure. 1. Fixed shutter mode When external trigger signal is POSITIVE (TriggerActivation: "RisingEdge"), after the trigger signal rise, exposure is start The exposure time is set by the camera electronic shutter speed.
  • Page 40 3. Reset control mode The readout timing can be set arbitrary set by input the trigger signal (Readout pulse) different from the exposure beginning when Fixed shutter mode or ONE Trigger mode. Execute following procedure in addition Fixed shutter mode/ONE trigger mode settings. (1) TriggerSelector →...
  • Page 41 4. Others Operation of the camera by the combination of each setting value is shown a table below. TriggerMode TriggerSource [TriggerSelector] [TriggerSelector] SETTING Exposure Exposure Exposure Mode Time Auto OPERATION Normal Don’t Don’t Don’t SHUTTER:OFF Don’t Care Don’t Care Care Care Care Don’t...

  • Page 42: Digital Output

    Digital output The method of setting of digital output is explained. 1. Flash out (strobe pulse) This camera can output flash pulse when trigger mode or electric shutter mode, (A) When output flash pulse at the same time as exposure time and without delay. (1) LineSelector →...

  • Page 43: Trigger Operation And Timing Chart

    Trigger operation and timing chart 1. Normal mode Shutter time (Camera setting value) Exposure Strobe delay (*1) Strobe output （High active） Strobe width1 (*2) Strobe width2 (*3) Data output VD output (Low active) 9H (*4) 1/Self frame rate [second] (*1) 0.08µs to 6.55ms Approx.
  • Page 44 2. Fixed shutter mode When external trigger signal is POSITIVE (high active), after the trigger signal rise, exposure is start. The exposure time is set by the camera electronic shutter speed. The video output is obtained immediately after the end of fixed exposure. The strobe signal start/end can be set to shutter time.
  • Page 45 4. VD reset mode When external VD pulse is inputted, internal VD is reset. Exposure time is established shutter speed. more than 1/self frame rate [sec] VD input (Falling Edge) more than 10μ s Data output VD output (Low active) 0.40±0.06µs NOTE: If the external VD of cycle which does not match the camera operation mode is input, shutter time has an error.

  • Page 46: Input / Output Signal

    Input / Output signal 1. Input signal The level of the trigger signal input to HV-F202GV is as follows. 5Vp-p ± 0.5V 2. Output signal The level of VD/Flash pulse signal output from HV-F202GV is as follows. 5Vp-p Spectral response...

  • Page 47: Specifications

    Specifications Specifications of HV-F202GV are showing. Optical system 1/1.8-inch F1.8 prism with IR cut filter Imaging device 1/1.8-inch interline CCD Total pixels 1688 (H) x 1248 (V) Effective pixels 1628 (H) x 1236 (V) Active pixels 1600 (H) x 1200 (V) Pixel pitch 4.4µm (H) x 4.4µm (V)

  • Page 48: Dimensions

    Dimensions...
  • Page 49 14-1 Sotokanda 4-choume, Chiyoda-ku, Tokyo 101-8980, Japan Phone: +81(0)3-6734-9432, Fax: +81(0)3-5209-5942 URL: http://www.hitachi-kokusai.co.jp/global/ Hitachi Kokusai Electric (Shanghai) Co., Ltd. Beijing Branch : Room 1415, Beijing Fortune Building, 5 Dong San Huan Bei-Lu, Chao Yang District, Beijing, 100004 China Phone: +86(0) 10-6590-8755/8756, Fax: +86(0) 10-6590-8757 Hiｔａｃｈｉ...

Table of Contents