IBM 9077 Get Connected page 196

/root netstat -in
Name
de0
de0
de0
rmb0
rmb0
lo0
lo0
lo0
gf000
gf000
gf001
gf001
gf002
gf002
gf003
gf003
7. On the CWS of SP21, check if the SP Switch Router Adapter card is
configured. To perform this check, look if the SP Switch Router Adapter
card shows up green in perspectives or enter
switch_responds
8. Issue some
On the chosen SP21 nodes,
SP2, for example:
root@sp21n01:/ ping 10.2.1.12
PING 10.2.1.12: (10.2.1.12): 56 data bytes
64 bytes from 10.2.1.12: icmp_seq=0 ttl=254 time=10 ms
64 bytes from 10.2.1.12: icmp_seq=1 ttl=254 time=1 ms
^C
----10.2.1.12 PING Statistics----
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 1/5/10 ms
On node 9-12 in SP2,
in SP21, for example:
root@sp2n12:/ ping 192.168.14.1
PING 192.168.14.1: (192.168.14.1): 56 data bytes
64 bytes from 192.168.14.1: icmp_seq=0 ttl=254 time=1 ms
64 bytes from 192.168.14.1: icmp_seq=1 ttl=254 time=1 ms
^C
----192.168.14.1 PING Statistics----
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 1/1/1 ms
178
IBM 9077 SP Switch Router: Get Connected to the SP Switch
Mtu Network Address
1500 <link1> 00:c0:80:96:38:68
1500 <Bridge> 00:c0:80:96:38:68
1500 192.168.4 192.168.4.4
616 <link2> 00:00:00:00:00:00
616 <GRIT> 0:0x40:0
1536 <link3>
1536 127 127.0.0.1
1536 <GRIT> 0:0x48:0
4352 <link10> 00:c0:80:89:2d:f2
4352 10.2.1/24 10.2.1.15
4352 <link20> 00:c0:80:89:2d:f3
4352 10.3.1/24 10.3.1.16
4352 <link11> 00:c0:80:89:2d:f4
4352 10.4.1/24 10.4.1.17
4352 <link12> 00:c0:80:89:2d:f5
4352 10.5.1/24 10.5.1.18
. Use
Eunfence
commands to check the connection:
ping
ping
the SP Switch interfaces of the chosen nodes
ping
Ipkts Ierrs
10290 0
10290 0
10290 0
170556 74
170556 74
8387 0
8387 0
8387 0
19 0
19 0
12 0
12 0
13 0
13 0
13 0
13 0
SDRGetObjects
if needed.
all four FDDI interfaces of the nodes in
Opkts Oerrs Coll
42228 0 182
42228 0 182
42228 0 182
41439 0 0
41439 0 0
8387 0 0
8387 0 0
8387 0 0
20 0 0
20 0 0
12 0 0
12 0 0
13 0 0
13 0 0
19 0 0
19 0 0