Related Manuals for AGP 1800W Electric Beveler model B15
Summary of Contents for AGP 1800W Electric Beveler model B15
-
Page 1: Instruction Manual
Instruction manual ►1800W Electric Beveler model B15 ►1100W Electric Beveler model B16 AC Induction Motor Mode For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. - Page 2 1800W Electric Beveler Mode Power input 1800 W Vlotage See machine nameplate No Load r.p.m. 2300-6500 Speed Wheel Settings 1/ 2/ 3/ 4/ 5/ 6: 2300/ 2600/ 3700/ 4800/ 5800/ 6500 Std. Bevel Angle 45 Deg. Max. Chamfer Height 45 Deg. : 10.6 mm Mini.
- Page 3 1100W Electric Beveler AC Induction Motor Mode Power input 1100W AC Induction Motor Voltage See machine nameplate No load r.p.m. 60Hz: 3600 , 50Hz: 3000 60 Deg. 12.7mm 45 Deg. 16mm MAX. adjustment for steel up to 45kg/mm2 37.5 Deg. 15.6mm 30Deg.
-
Page 4: General Safety Rules
GENERAL SAFETY RULES path to carry electricity away from the user. Double insulated tools are equipped with a WARNING! Read and understand all polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet instructions. - Page 5 Use safety equipment. Always wear eye Disconnect the plug from the power source protection. Safety equipment such as dust before making any adjustments, changing mask, non-skid safety shoes, hard hat, or accessories, or storing the tool. Such hearing protection used for appropriate preventive safety measures reduce the risk conditions will reduce personal injuries.
- Page 6 WARNING: To reduce the risk of injury, user or other reproductive harm. must read instruction manual. An example of these chemicals are: Symbols used in this manual lead from lead-based paint V……..volts Your risk from these exposures varies, A……..amperes depending on how often you do this Hz……hertz type of work.
-
Page 7: Electrical Connection
For machining workpieces in steel, chrome prevent an excessive drop in voltage or steel alloys, aluminum, aluminum alloys, overheating. An excessive drop in voltage brass and plastic. The machine is designed reduces the output and can lead to failure exclusively for Adding beveled edges, of the motor. - Page 8 S E T T I N G T H E C H A M F E R H E I G H T Once the zero point is found, loosen DISCONNECT TOOL FROM POWER SOURCE. the small set screw and turn the dial ring to indicate zero on the scale.
- Page 9 CHANGING THE INDEXABLE CARBIDE Index the carbide insert to the next INSERTS sharp edge or insert a new one as DISCONNECT TOOL FROM POWER SOURCE. needed. Retighten carbide insert with its torx WARNING: Danger of Burns! Tool holder and fixing screw. carbide inserts become hot in operation.
- Page 10 Replace and adjust the support deck assembly. Hook spanner Tool holder wrench Open-end wrench CHANGING THE INDEXABLE CARBIDE Hex. Wrench INSERTS DISCONNECT TOOL FROM POWER SOURCE. LAND WIDTH ADJUSTMENT For 1100W Electric Beveler AC Induction Motor Mode The land width of the AC Induction Motor Mode is factory set to a maximum of Loosen the 2 Depth Adjustment Screw 25.4mm, and is continuous adjustable...
- Page 11 STARTING AND STOPPING TOOL the arbor will still rotate for a time. Take care that parts of your body do not come Make sure that the power circuit voltage is t into contact with the rotating parts or set h e s a m e a s t h a t s h o w n o n t h e the machine down while it is still rotating! specification plate of the machine and that switch is “OFF”...
- Page 12 SPEED CONTROL WHEEL d e c k f l a t a n d s e c u r e l y t o t h e workpiece From operator’s There is a progressive variable speed wheel. perspective, the spindle is spinning clockwise, so always operate in the By turning the wheel to the right,, the speed direction from left to right (up mill).
- Page 13 For 1800W models: workpiece surfaces will be machined unevenly. Replace when worn as follows: To replace: Using supplied hook spanner wrench, engage one of the holes in First unplug the machine. Carefully remove the tool holder to immobilize it. the 4 screws to separate the rear handle Using an appropriate sized wrench halves and then remove the 4 screws which loosen the nut securing the impeller...
- Page 14 when it is retightened. ●If the replacement of the power supply cord is necessary, this has to be done by the manufacturer or their agent in order to avoid a safety hazard.
- Page 15 WIRING (1800W Mode)
- Page 16 WIRING (1100W AC Induction Motor Mode) MOTOR 3-WAY CONNECTOR SWITCH BLACK YELLOW BLACK EARTH CAPACITOR...
- Page 18 PARTS LIST (1800W Mode) Parts Name Q'TY Parts Name Q'TY POWER SUPPLY CABLE SPIRAL BEVEL GEAR M1.5 47T CORD ARMOR INTERNAL CIRCLIP R-47 CABLE CLIP EXTERNAL CIRCLIP S-20 SCREW M4 x 14 BALL BEARING 6204-2RS SWITCH LOCK-ON WOODRUFF KEY 5 x 5 x 12 SCREW M4 x 30 SPINDLE SCREW M4 x 16...
- Page 19 EXPLODED VIEW (1100W AC Induction Motor Mode) 39 40 15 16 17...
- Page 20 PARTS LIST (1100W AC Induction Motor Mode) Parts Name Q'TY Parts Name Q'TY FRONT HANDLE SCREW M5 x 8 SCREW M14 x 25 CONTROL BOX INNER COVER CAPACITOR 400VAC, 20UF SCREW M10 x 20 230V / 250VAC, 20UF 110V FLAT WASHER Ø10 x Ø23 x 2 SWITCH PANEL DEPTH ADJUST NUT...
- Page 21 N.KO spol. s r.o. Táborská 398/22 293 01 Mladá Boleslav Czech republic phone: +420 326 772 001 fax: +420 326 774 279 e-mail: nko@nko.cz...