Table of Contents
Advertisement
Quick Links
Original instructions
For your personal safety,
READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION:
For tools equipped with overload protection, when the motor shuts
off due to overload, always run the machine with no load for at least
3 minutes to reduce temperature before returning to operation to
avoid burn-out of the motor.
Version:20160824
Advertisement
Table of Contents
Related Manuals for AGP SM125
Summary of Contents for AGP SM125
- Page 1 Original instructions For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. CAUTION: For tools equipped with overload protection, when the motor shuts off due to overload, always run the machine with no load for at least 3 minutes to reduce temperature before returning to operation to avoid burn-out of the motor.
- Page 2 Power Scouring Machine Tailcover Motor Housing Side Handle Auxiliary Handle Vacuum Connection Port Lock Button Main Handle On/Off Switch Adjustor Knob Adjustor Knob Depth Adjustment Slot Cutter Discs Extraction shroud/base plate Rotary Scarifier Wheel See machine nameplate Voltage Power Input 1200W No load min 2800...
-
Page 3: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS sharp edges or moving parts. Damaged or entangled cords increase the risk of electric WARNING! Read all safety warnings and shock. all instructions. Failure to follow the When operating a power tool outdoors, use an extension cord suitable for outdoor use. warnings and instructions may result in electric shock, fire and/or serious injury. - Page 4 or jewelry. Keep your hair, clothing and b i t s e t c . , i n a c c o r d a n c e w i t h t h e s e gloves away from moving parts. Loose instruc tions, taking into account the clothes, jewelry or long hair can be caught in working conditions and the work to be...
- Page 5 Safety Warnings Common for power tool at maximum no-load speed for Grinding Operations: one minute. Damaged accessories will normally break apart during this test time. This power tool is intended to function as Wear personal protective equipment. a grinder. Read all safet y warnings, Depending on application, use face shield, i n s t r u c t i o n s , i l l u s t r a t i o n s a n d safety goggles or safety glasses.
-
Page 6: Electrical Connection
Do not operate the power tool near snagging the accessory. Corners, sharp flammable materials. Sparks could ignite edges or bouncing have a tendency to snag these materials. the rotating accessory and cause loss of Do not use accessories that require liquid control or kickback. -
Page 7: Safety Symbols
chemicals are: voltage indicated on the tool name plate. Under no circumstances should the tool be • Lead from lead-bases paints used when the power supply cable is damaged. • Crystalline silica from bricks, cement and A d a m a g e d c a b l e m u s t b e r e p l a c e d other masonry products immediately by an authorized Customer Service •... - Page 8 injury from accidentally starting, before possible hearing damage, wear earplugs or changing any setup. muffs. • Check for proper alignment of moving parts. Whenever Machine Is Running • Check for damaged electric cords. • Check for binding of moving parts. WARNING: Don’t allow familiarity (gained from •...
-
Page 9: Electrical Connections
Look for this symbol to point out important terminals of plug when installing or removing safety precautions. It means ATTENTION!!! Your the plug from the outlet to avoid injury or safety is involved . possible death from electrical shock. Motor and Electrical Requirements WARNING: If not properly grounded, this tool can cause an electrical shock, particularly when WARNING: To reduce the risk of electrical... -
Page 10: Wire Sizes
WIRE SIZES Side Handle............ 1 T-Wrench....………………………..1 NOTE: Make sure the proper extension cord is used Pyramid-tipped Cutter Discs....15 and is in good condition. Use only 3-wire extension Wheel Puller........... 1 cords that have 3-prong grounding plugs and Rotary Scarifier Wheel........1 3-pole receptacles that accept the tool’s plug. -
Page 11: Vacuum Connection
contact with the rotating parts or set the Loosen the 3 black Adjustor Knobs and rotate machine down while it is still rotating! the Depth Shroud base to set the desired How to use the Tool milling depth. Tighten the Adjustor Knobs securely. Effective control of this machine requires two- Attach additional side handle. - Page 12 THE EDGE CUT-OUT When working against a wall or into a corner, the Depth Shroud Base will prevent the grinding head from reaching all the way to the edge. In this case, one may remove the 3 knobs and remove the entire Depth Shroud Base.
- Page 13 the 2 shoulder bolts to remove the Inner Reinsert Inner Retaining Cup and attach with Retaining Cup. the 2 shoulder bolts and tighten with the T-wrench. A r b o r b o l t Inner retaining ring and washer Inner retaining ring shoulder bolts Arbor bolt and...
- Page 14 I N S TA L L I N G O P T I O N A L 1 - P I E C E Engage the lock nut wrench in the 2 holes on the D I A M O N D C U P W H E E L S W / 7 / 8 " disc to keep from turning and use the T-wrench to (22.23MM) BORE.
-
Page 15: Replacing Carbon Brushes
REPLACING CARBON BRUSHES MAINTENANCE The carbon brushes are a normal wearing part and WARNING: To reduce the risk of injury from must be replaced when they reach their wear limit. unexpected starting or electrical shock, unplug the power cord before working on the machine. CAUTION: Always replace the brushes as a pair. -
Page 16: Tool Storage
TOOL STORAGE IMPORTANT: When the Power Scouring Machine is not being used DO NOT leave it resting on the Extraction/Shroud base plate or on the motor (tail cover) WARNING: If the replacement of the power supply cord is necessary, this has to be done by the manufacturer or their agent in order to avoid a safety hazard. - Page 17 WIRING 110V 230V CARBON BRUSH MOTOR CARBON BRUSH BROWN SWITCH BLUE...
-
Page 18: Exploded View
EXPLODED VIEW... - Page 19 EXPLODED VIEW Parts Name Q'TY Parts Name Q'TY SCREW M5 x 25 SHOULDER BOLT M5 TAIL COVER DEPTH SHROUD BASE SCREW M4 x 10 ADJUSTOR KNOB M5 x 7 SCREW M4 x 12 SPRING FRONT HANDLE BRUSH HOLDER 7 x 11 SIDE HANDLE CARBON BRUSH 7x 11 HANDLE COVER - RIGHT...