Advertisement
1)
Introduction
2)
3)
4)
Unit Layout & Description
5)
Connection and Operation
6)
Connection Diagram
7)
KanexPro™ reserves the right to make changes in the hardware, packaging and any accompanying docu-
mentation without prior written notice
1x8 VGA Extender over CAT5/6 with Audio up to 1,000ft. (300m)
The KanexPro 1x8 VGA extender over a single CAT5e/6 cable is designed for routing and distributing
four high-resolution VGA signals and stereo audio over remote distances up to 1,000ft (300m) Each
receiver set features a separate gain and peaking rotary switch used in adjusting brightness and skew
over long distances The 15-pin HD connectors are convenient and cost-effective for all input/ output
connections supporting full bandwidth Fully compatible with VGA to WUXGA graphics cardresolution
and HDTV's to projectors In addition, each output performs a separate buffering to maintain signal
integrity and reject noise interference
Features:
• Extend eight independent high-resolution VGA signals with audio over Cat5E/6 cables up to
1,000 feet (300m)
• Adjust GAIN and PEAK levels to adapt for variable lengths of UTP cable on the receiver side
• Supports maximum resolutions up to WUXGA (1920x1200@60Hz)
• Stereo audio through 3.5mm jack
• Dual output for transmitter: VGA for local display and 8 x Cat5e/6
• EDID Compliant
• Rack or under-desk mountable
• 5VDC external power supply included
TM
Setup Guide
Table of Contents
Notice
1
Introduction
1
VGAEXTX8
1
2
2
3
3
4
4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for KanexPro VGAEXTX8
Summary of Contents for KanexPro VGAEXTX8
- Page 1 1x8 VGA Extender over CAT5/6 with Audio up to 1,000ft. (300m) The KanexPro 1x8 VGA extender over a single CAT5e/6 cable is designed for routing and distributing four high-resolution VGA signals and stereo audio over remote distances up to 1,000ft (300m) Each...
-
Page 2: Specifications
Specifications Transmitter(TX) Interface: Input: VGA x1/3 5mm Stereo x1 Output: Cat 5e/6 x8/VGA Output (Local) x1/3 5mm Stereo x1 Receiver (Rx) Input: Cat 5e/6 x1 Output: VGA x1/3 5mm Stereo x1 Operating Frequency: Vertical Frequency Range 60/75/85Hz Resolutions (PC): 640x480 800x600 1024x768 1280x720 1280x768 1280x960 1280x1024 1600x900... - Page 3 Unit Layout & Description Transmitter Front Power VGA Input VGA Output Power VGA Input VGA Output Back VGA Input Output 8 Output 7 Output 6 Output 5 Output 4 Output 3 Output 2 Output 1 Output 8 Output 7 Output 6 Output 5 Output 4 Output 3...
-
Page 4: Connection And Operation
Connection and Operation Connect VGA source(PC, laptop, etc) and the 3 5mm audio cable to the VGA and stereo audio input of the VGA Extender Tx unit 2) Connect CAT5 output from the Tx to the VGA Extender Rx unit using a UTP Cat5e/6 cable. Plug local VGA display to the VGA Output and Audio Out on the Tx unit 4) Connect VGA display(Monitor, Projector, etc) to the VGA output on the Rx unit as well as the audio out to the display 5) Add power supplies to the Tx and Rx units. - Page 5 KanexPro’s entire liability and Customer’s exclusive remedy shall be, at KanexPro option, either return of the price paid for the product, or repair or replacement of the Product that does not meet this Limited Warranty and which is returned to KanexPro with a copy of customer’s receipt This Limited Warranty is void if failure of the Product has resulted from accident, abuse, or misapplication Any replace-...
Need help?
Do you have a question about the VGAEXTX8 and is the answer not in the manual?
Questions and answers