Related Manuals for ESAB Origo Mig 410
Summary of Contents for ESAB Origo Mig 410
- Page 1 Mig 410 Mig 510 ™ ™ ™ ™ Origo Instruction manual 0349 301 122 070104 Valid for serial no. 627...
-
Page 2: Table Of Contents
ENGLISH 1 DIRECTIVE ............2 SAFETY . -
Page 3: Directive
DIRECTIVE DECLARATION OF CONFORMITY ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld- ing power source Origo Mig 410 / Origo Mig 510 from serial number 627 complies with standard IEC/EN 60974--1, in accordance with the requirements of directive (73/23/EEC) and addendum (93/68/EEC) and with standard IEC/EN 60974--10 in accordance with the requirements of directive (89/336/EEC) and addendum (93/68/EEC). - Page 4 WARNING! Read and understand the instruction manual before installing or operating. WARNING ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU- TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE BASED ON MANUFACTURERS’ HAZARD DATA. ELECTRIC SHOCK - - Can kill Install and earth the welding unit in accordance with applicable standards.
-
Page 5: Introduction
The machines can be fitted with an instrument for display of current and voltage. It incorporates a hold function and can be calibrated. The machines can be fitted with a flow guard. ESAB’s accessories for the product can be found on page 20. Equipment The power source is supplied with:... -
Page 6: Installation
Origo Mig 510 Voltage 400--415V, 3∼ ∼ ∼ ∼ 50/60 Hz 230/400--415/500V 3∼ ∼ ∼ ∼ 50 Hz 230/440--460 3∼ ∼ ∼ ∼ 60Hz Permissible load at100 % duty cycle 390 A/33,5 V 390 A/33,5 V at 60 % duty cycle 500 A/39 V 500 A/39 V Setting range (DC) -
Page 7: Placing
Placing Position the welding power source such way that its cooling air inlets and outlets are not obstructed. Assembly of components WARNING! During transport, the rear wheels of the power source are in their forward position. Before use, place the wheels in their rear position. - - 7 - - mi410,510e... -
Page 8: Assembly Of Counter Balance
Assembly of counter balance Assemble the stabilizer + CB KIT if the counter balance is to be installed on machine. The stabilizer + CB KIT is an accessory. Ordering number you can find on page 21. Attention! Utilization of counter balance without stabilizer may cause the machine tipping over. - Page 9 Origo Mig 510 - - 9 - - mi410,510e...
-
Page 10: Mains Power Supply
Mains power supply Check that the unit is connected to the correct mains power supply voltage, and that it is protected by the correct fuse size. A protective earth connection must be made, in accordance with regulations. Rating plate with supply connection data Origo Mig 410 3∼... -
Page 11: Operation
NOTE! Cooling water connections only available on certain models. * Indicating loss of coolant, only when water flow guard is used, see point 6.5 ** ELP = ESAB Logic Pump, see point 6.4. - - 11 - - mi410,510e... -
Page 12: Start
Water connection The Origo Feed has a sensor ELP, ESAB Logic Pump, which senses whether the water hoses of the welding gun are connected. When a water--cooled welding gun is connected, the water pump is active. For the Feeds the pump supply switch on the power source should be left in position ”0/ELP”. -
Page 13: Maintenance
MAINTENANCE Regular maintenance is important for safe, reliable operation. Note! All guarantee undertakings from the supplier cease to apply if the customer himself attempts any work in the product during the guarantee period in order to rectify any faults. Inspection and cleaning Check regularly that the power source is free from dirt. -
Page 14: Fault Tracing
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication. -
Page 15: Diagram
Diagram Origo Mig 410 (400- - 415V) - - 15 - - mi410,510di... - Page 16 Origo Mig 410 (230- - 500V) - - 16 - - mi410,510di...
- Page 17 Origo Mig 510 (400- - 415V) - - 17 - - mi410,510di...
- Page 18 Origo Mig 510 (230- - 500V) - - 18 - - mi410,510di...
-
Page 19: Ordering Numbers
Origo Mig 410, Origo Mig 510 Valid for serial no. 627- -XXX- -XXXX Ordering numbers 0349 302 408 Origo Mig 410 400--415V 3∼ ∼ ∼ ∼ 50Hz 0349 302 713 Origo Mig 410 230/400--415/500V 3∼ ∼ ∼ ∼ 50Hz; 230/440--460V 3∼ ∼ ∼ ∼ 60Hz 0349 302 407 Origo Mig 410w 400--415V 3∼... -
Page 20: Accessories
Origo Mig 410, Origo Mig 510 Accessories NO TAG Feeder with capsulated bobbin, M11 panel Origo Feed 302 ......0459 116 781 Origo Feed 302 with water . - Page 21 Origo Mig 410, Origo Mig 510 Filter ........0349 302 423 Cable holder .
- Page 22 ESAB subsidiaries and representative offices Europe Asia/Pacific Representative offices NORWAY AS ESAB AUSTRIA BULGARIA CHINA Larvik ESAB Ges.m.b.H ESAB Representative Office Shanghai ESAB A/P Tel: +47 33 12 10 00 Vienna- -Liesing Sofia Shanghai Fax: +47 33 11 52 03...