Service Call Errors; Warnings - Canon PIXUS iP8600 Service Manual

2-2. Service Call Errors (by LED Blinking in Orange and Green Alternately, or Lit in Orange)
LED alternate
blinking in orange and
green
2 times Carriage error [5100]
3 times Paper feed error [6000]
4 times Purge unit error [5C00]
5 times ASF (cam) sensor error [5700]
6 times Internal temperature error [5400]
7 times Waste ink absorber full [5B00]
8 times Print head temperature rise error [5200]
9 times EEPROM error [6800]
11 times Carriage lift mechanism error [5110]
12 times AP position error [6A00]
13 times Paper feed position error [6B00]
14 times Paper feed cam sensor error [6B10]
15 times USB Host VBUS overcurrent [9000]
16 times Valve sensor error [6C00]
17 times Motor driver error [6D00]
20 times Other hardware error [6500]
Continuous alternate ROM error
blinking
Lights in orange RAM error
*1: Before replacement of the logic board ass'y, check the waste ink amount (by service test print or EEPROM information print). If the waste ink amount is 7%
or more, also replace the bottom case unit (QM2-1583) or the ink absorbers (QC1-5381 / 5382 / 5383 / 5384 / 5385 / 5386 / 5387 / 5388 / 5389 / 5390)
when replacing the logic board ass'y.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]
*2: Reset the waste ink counter when replacing the bottom case unit.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]

2-3. Warnings

Printer (no LED indications):
Displayed warning
Low ink of BCI-6BK / C / M / Y / PC / PM / R / G (at
detection of no remaining raw ink)
Print head temperature rise
Protection of excess rise of the print head temperature
*1: If the warning is displayed, the carriage does not move to the ink tank replacement position when the access cover is opened.
Error [Error code]
- Carriage unit (QM2-1586)
- Timing slit strip film (QC1-5373)
- Logic board ass'y (QM2-1616)
- Carriage motor (QK1-0545)
- Timing sensor unit (QM2-1587)
- Timing slit disk film (QC1-4375)
- Feed roller ass'y (QL2-0742)
- Platen unit (QM2-1831)
- Logic board ass'y (QM2-1616)
- PAPER FEED MOTOR (QK1-0550)
- Purge unit (QM2-1590)
- Logic board ass'y (QM2-1616)
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1616)
- Ink absorber (QC1-5381 / 5382 / 5383 / 5384 / 5385 / 5386 / 5387 / 5388 / 5389 /
- Bottom case unit (QM2-1583)
- Print head (QY6-0055)
- Logic board ass'y (QM2-1616)
- Logic board ass'y (QM2-1616)
- Lift shaft(QC1-4331)
- Photo interrupter (WG8-5624)
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1616)
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1616)
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1616)
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1616)
- Logic board ass'y (QM2-1616)
- Purge unit (QM2-1590)
- Logic board ass'y (QM2-1616)
- Logic board ass'y (QM2-1616)
- Logic board ass'y (QM2-1616)
- Logic board ass'y (QM2-1616)
- Logic board ass'y (QM2-1616)
Status indication only.
If the print head temperature is high when the access cover is opened, the warning is displayed
When the print head temperature falls, the warning is released.
If the print head temperature exceeds the specified limit, a Wait is inserted during printing,
(Replacement of listed parts, which are likely to be faulty)
*1
*1
*1
*1
5390)
*2
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
Remarks
1 - 4
Solution
*1 .