Dell Studio 1435 Service Manual

Notebook dell studio 1435
Hide thumbs Also See for Studio 1435:

Advertisement

Dell Studio™ 1435 Service Manual 
Before You Begin
Base Cover
Hard Drive
Memory
Wireless Mini-Cards
Fan
Processor Heat Sink
Processor
Center Control Cover
Keyboard
Palm Rest
 Notes, Notices, and Cautions
NOTE:
A NOTE indicates important information that helps you make better use of your computer.
NOTICE:
A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION:
A CAUTION indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2008 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.;Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under
license. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Model PP24L
October 2008 Rev. A00
Optical Drive
Speakers
Audio Board
Display
Camera (Optional)
Microphone
Coin-Cell Battery
System Board
WiFi Sniffer Board
Flashing the BIOS

Advertisement

Table of Contents
loading

Summary of Contents for Dell Studio 1435

  • Page 1 Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.;Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under license.
  • Page 2: Removing The Audio Board

    Back to Contents Page   Audio Board Dell Studio™ 1435 Service Manual    Removing the Audio Board   Replacing the Audio Board   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
  • Page 3: Removing The Base Cover

    Back to Contents Page   Base Cover Dell Studio™ 1435 Service Manual    Removing the Base Cover   Replacing the Base Cover   CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer.   CAUTION: Before performing this procedures, turn off the computer, disconnect the AC adapter from the electrical outlet and the computer, disconnect the modem from the wall connector and the computer, and remove any other external cables from the computer.
  • Page 4: Before You Begin

    Hold a component such as a processor by its edges, not by its pins. NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
  • Page 5 To help prevent damage to the system board, you must remove the battery from the battery bay before you service the computer. NOTICE: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers.
  • Page 6: Flashing The Bios From A Cd

    1. Ensure that the AC adapter is plugged in, the main battery is properly installed, and a network cable is attached.   2. Turn on the computer.   3. Locate the latest BIOS update file for your computer at support.dell.com.   4. Click Download Now to download the file.  ...
  • Page 7: Camera (Optional)

    Back to Contents Page   Camera (Optional) Dell Studio™ 1435 Service Manual    Removing the Camera   Replacing the Camera   CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
  • Page 8: Removing The Center Control Cover

    Back to Contents Page   Center Control Cover Dell Studio™ 1435 Service Manual    Removing the Center Control Cover   Replacing the Center Control Cover   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.
  • Page 9: Replacing The Center Control Cover

     Replacing the Center Control Cover   1. Slide the media control buttons cable into the connector on the center control cover until it is in position and pull down on the connector latch that secures the cable to the connector.  ...
  • Page 10: Removing The Coin-Cell Battery

    Back to Contents Page   Coin-Cell Battery Dell Studio™ 1435 Service Manual    Removing the Coin-Cell Battery   Replacing the Coin-Cell Battery   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
  • Page 11  ...
  • Page 12: Removing The Processor

    Back to Contents Page   Processor Dell Studio™ 1435 Service Manual    Removing the Processor   Installing the Processor   CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
  • Page 13 When the processor is correctly seated, all four corners are aligned at the same height. If one or more corners of the processor are higher than the others, the processor is not seated correctly. NOTICE: To prevent intermittent contact between the ZIF-socket cam screw and the processor when removing or replacing the processor, press to apply slight pressure to the center of the processor while turning the cam screw.
  • Page 14: Removing The Processor Heat Sink

    Back to Contents Page   Processor Heat Sink Dell Studio™ 1435 Service Manual    Removing the Processor Heat Sink   Replacing the Processor Heat Sink   CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
  • Page 15 Back to Contents Page  ...
  • Page 16: Display Assembly

    Back to Contents Page   Display Dell Studio™ 1435 Service Manual    Display Assembly   Display Bezel   Display Panel   Display Panel Cable   Inverter Board   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
  • Page 17: Replacing The Display Assembly

    1 display cable screw 2 camera cable pull-tab (optional) 3 power button cable connector 4 display cable pull-tab   11. Remove the two screws (one on each hinge).   12. Remove the display assembly. display assembly screw (2)   Replacing the Display Assembly  ...
  • Page 18: Display Panel

      11. Slide the battery into the bay until it clicks into place.  Display Bezel   Removing the Display Bezel NOTICE: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel.   1. Follow the instructions in Removing the Display Assembly.
  • Page 19: Display Panel Cable

    display panel screw (4) inverter board screw (2) inverter board display panel   5. Remove the inverter board (see Removing the Inverter Board).   6. Remove the display panel assembly.   7. Remove the eight screws (four on either side)securing the display bracket. 1 screw (8 total;...
  • Page 20: Inverter Board

      2. Remove the display bezel (see Removing the Display Bezel).   3. Remove the display panel (see Removing the Display Panel).   4. Turn the display panel over and place it on a clean surface. display cable securing clip (2) back of display panel  ...
  • Page 21: Replacing The Inverter Board

      Replacing the Inverter Board   1. Connect the cables to the connectors on either side of the inverter board.   2. Replace the display panel along with the inverter board (see Replacing the Display Panel).   3. Replace the display bezel (see Replacing the Display Bezel).
  • Page 22: Removing The Fan

    Back to Contents Page   Fan Dell Studio™ 1435 Service Manual    Removing the Fan   Replacing the Fan   CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
  • Page 23 Back to Contents Page  ...
  • Page 24: Removing The Hard Drive

    Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell. NOTE: If you are installing a hard drive from a source other than Dell, you need to install an operating system, drivers, and utilities on the new hard drive (see the Dell Technology Guide).
  • Page 25: Replacing The Hard Drive

    6. Slide the battery into the bay until it clicks into place.   7. Install the operating system for your computer, as needed (see Dell Technology Guide).   8. Install the drivers and utilities for your computer, as needed (see Dell Technology Guide). Back to Contents Page  ...
  • Page 26: Removing The Keyboard

    Back to Contents Page   Keyboard Dell Studio™ 1435 Service Manual    Removing the Keyboard   Replacing the Keyboard   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
  • Page 27: Replacing The Keyboard

    screw (2) keyboard keyboard tab (6) connector latch keyboard cable       7. Rotate the keyboard downward to expose the keyboard cable.   8. Release the connector latch that secures the keyboard cable to the connector on the system board and remove the cable.  ...
  • Page 28: Removing The Memory Module(S)

    Install only memory modules that are intended for your computer. NOTE: Memory modules purchased from Dell are covered under your computer warranty. Your computer has two user-accessible SODIMM sockets that can be accessed from the bottom of the computer. The DIMM B memory module is located directly above the DIMM A memory module located on the bottom of the computer.
  • Page 29 As the computer boots, it detects the additional memory and automatically updates the system configuration information. To confirm the amount of memory installed in the computer, click Start ® Help and Support® Dell System Information. Back to Contents Page  ...
  • Page 30: Removing The Microphone

    Back to Contents Page   Microphone Dell Studio™ 1435 Service Manual    Removing the Microphone   Replacing the Microphone   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
  • Page 31: Wireless Mini-Cards

    NOTE: Dell does not guarantee compatibility or provide support for Mini-Cards from sources other than Dell. If you ordered a wireless Mini-Card with your computer, the card is already installed. Your computer supports two Mini-Card slots:  one Full Mini-Card slot –...
  • Page 32: Replacing The Mini-Card

    9. Install the drivers and utilities for your computer, as required. For more information, see the Dell Technology Guide. NOTE: If you are installing a Mini-Card from a source other than Dell, you must install the appropriate drivers and utilities. For more generic driver information, see the Dell Technology Guide.
  • Page 33: Removing The Optical Drive

    Back to Contents Page   Optical Drive Dell Studio™ 1435 Service Manual    Removing the Optical Drive   Replacing the Optical Drive   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
  • Page 34: Removing The Palm Rest

    Back to Contents Page   Palm Rest Dell Studio™ 1435 Service Manual    Removing the Palm Rest   Replacing the Palm Rest   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
  • Page 35: Replacing The Palm Rest

    while pulling on the outside. palm rest  Replacing the Palm Rest   1. Align the palm rest with the computer base and gently snap the palm rest in place.   2. Connect the power sensor cable, touch pad cable, and fingerprint cable (optional) to the respective system board connectors.  ...
  • Page 36: Removing The Speakers

    Back to Contents Page   Speakers Dell Studio™ 1435 Service Manual    Removing the Speakers   Replacing the Speakers   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
  • Page 37   4. Connect the display cable to the connector on the system board.   5. Replace the screw that secures the display cable.   6. Replace the optical drive (see Replacing the Optical Drive).   7. Replace the palm rest (see Replacing the Palm Rest).
  • Page 38: Removing The System Board

    Back to Contents Page   System Board Dell Studio™ 1435 Service Manual    Removing the System Board   Replacing the System Board   CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
  • Page 39   4. Connect the speaker cable to the system board connector (see Replacing the Speakers).   5. Replace the palm rest (see Replacing the Palm Rest).   6. Replace the keyboard (see Replacing the Keyboard).   7. Replace the center control cover (see Replacing the Center Control Cover).
  • Page 40 Back to Contents Page   WiFi Sniffer Board Dell Studio™ 1435 Service Manual    Removing the WiFi Sniffer Board   Replacing the WiFi Sniffer Board  Removing the WiFi Sniffer Board   1. Follow the instructions in Before You Begin.   2. Remove the center control cover (see Removing the Center Control Cover).
  • Page 41   2. Connect the WiFi sniffer board cable to the system board connector.   3. Replace the palm rest (see Replacing the Palm Rest).   4. Replace the keyboard (see Replacing the Keyboard).   5. Replace the center control cover (see Replacing the Center Control Cover).

Table of Contents