Table of Contents
Advertisement
4. Insert the U-shaped part of the media support bar
into the frame.
No.
Name
No.
1
Media support bar
2
5. Insert the screws (one for each hole).
Insert the screws from below.
1
2
No.
Name
No.
1
Media support bar
2
6. Use the thumb screw to fix Stopper on Frame.
・Install Stopper on the side of rail retaining screw.
・Install Stopper so that the curved part matches
Frame.
4
2
3
1
No.
Name
No.
1
Frame
3
2
Stopper
4
7. Use the screws (2 pieces each) and fix Installation
plates (R and L) on Frame.
Install Installation plates on the opposite side of rail
fixing screw.
3
3
1
2
3
No.
Name
No.
1
Installation plates (R)
3
2
Installation plates (L)
4
8. Assemble the other side of media-feed table in the
same way.
4 Installation
Procedures and environment for installing this product
are explained.
4.1 Installation environment
Install this product to the appropriate place with
reference to the following.
WARNING
Do not install the printer in the following places
where there is a possibility that the printer may
Name
be damaged or might fall or be fallen by chance.
Frame
Do not step on the printer or place heavy
things on top of it.
It may cause an injury if the printer falls down.
Do not block the vent by covering the printer
with cloths, such as a blanket or tablecloth. If
the vent is blocked, heat may accumulate
inside the printer and it may cause fire.
Do not install the printer in a location that
has high humidity or is dusty.
Name
It could lead to electric shock and fire.
Screws
4.1.1 Installation environmental condition
Select an installation location in accordance with the
table below.
Floor strength of
installation place
Power
2
Specifiction
Environ-
3
mental
conditions
NOTE
For temperature and humidity, avoid locations
such as the following. There is a possibility that
the print quality will be affected.
Places where temperature or humidity may rapidly
change, even though within the required conditions.
Name
Places that receive direct sunlight, increased
Thumb screw
Rail retaining screw
illumination or direct air, for example from an air
conditioner.
To keep the temperature and humidity constant,
install this product in a location where the air
condition is adjustable.
4.1.2 Installation space
1
Install on a level floor which meets the following condition.
It has enough strength to support the weight of the
printer and the stand.
NOTE
For the weight of the printer and the stand, refer to
the Operation Manual.
(1) When using the media-feed table
Name
1,000mm
Frame
Screw
On a shaky stand
Slanting location
Places where vibration of other
machines etc. is transmitted.
More than 2940 Pa (300 kg/m
Rated voltage
AC100-240V
Frequency
50/60Hz ± 1Hz
range
Current
100V-240V: 10.0 A - 4.0A
consumption
Operative
Temperature: 20 °C to 32 °C
Humidity: 40% to 60%, No Condensation
condition
Printing
Temperature: 22 °C to 30 °C
accuracy
Humidity: 40% to 60%, No Condensation
coverage
Temperature: within 2 °C per one hour
Change rate
Humidity: within 5% per one hour
1,000mm
2,983mm
4,983mm
5
VJ-1638UH MarkⅡ INSTALLATION MANUAL
(2) When not using the media-feed table
1,000mm
2,983mm
4,983mm
4.2 Installation procedure
Install this product to the installation place in
accordance with the list shown below.
4.2.1 Installing the printer main unit
1. Carry the printer to the installation place.
2. Turn the following adjusters in the direction as
shown below to prevent the printer from moving.
Stand: adjusters (4)
2
)
1
No.
Name
1
Adjusters
3. Set the level on the right and left platens and
adjust so that the printer stays flat.
2
No.
Name
1
Level
4. Check that the two-way valve of the drain tube is
closed. Hook the two-way valve on the clamp,
then close the clamp cover.
Close
1
No.
Name
1
Two-way valve
1,000mm
1,000mm
1,000mm
1
2
1
No.
Name
2
Stand
1
1
2
No.
Name
2
Adjusters
1
2
No.
Name
2
Two-way valve clamp
VJ1638UH2E-I-02
Advertisement
Table of Contents
