Location Of Parts And Operation - Sony XC-ST50 Technical Manual

LOCATION OF PARTS AND OPERATION

XC-ST50/50CE
XC-ST30/30CE
2
(XC-ST50 model)
CCD
1
2 3
5
412-pin multi-connector
Pin No.
* 1: An input VD signal is required when the restart/reset mode is used.
2: A WEN output signal is valid only in the external trigger shutter mode.
*
• Factory-setting mode of rear panel
Corresponding
No.
γ correction ON/OFF selector switch
6
7 Internal/external sync selector switch
8
Trigger polarity selector switch
75 Ω termination selector switch
9
Selection DIP switch
0
1, 2, 3, 4: Selects the Shutter speed.
5: Selects the field and frame integration.
6, 7, 8: Selects the normal shutter, external trigger shutter, and restart/reset.
A
GAIN switch
VIDEO CAMERA MODULE
XC-ST50
6 7 4
A B = 9
External HD/VD Internal HD/VD
synchronization synchronization
1 GND
2 +12 V +12 V
3 GND
4 VIDEO output VIDEO output
5 GND
6 External HD input Internal HD output
1
7 * External VD input Internal VD output
8 GND
9 –
2 2
10 * WEN output * WEN output
11 TRIG input TRIG input
12
GND
Switch
4 5
3
8
External VS
synchronization
GND GND
+12 V
GND GND
VIDEO output
GND GND
–
VS
GND GND
– –
2
* WEN output
TRIG input
GND GND
Factory-setting
mode
OFF
EXT
+
ON
OFF
(All set to
the left.)
FIX
1 Lens mount section
A commercial C-mount lens as well as a
Sony standard lens can be used.
2 Camera mounting reference hole
These screw holes are positioned with
high precision related to CCD sensor.
3 Screw hole for tripod adaptor mounting
(VCT-ST70I)
4 12-pin multi-connector
DC IN/SYNC (DC power/sync signal input)
5 BNC connector
VIDEO OUT
6 γ correction
ON/OFF selector switch
7 Internal/external sync selector
switch
The camera operates with internal syn-
chronization when there is no external
sync input signal in the EXT position.
In this case, an HD/VD signal is not out-
put from the 12-pin multi-connector.
8 Trigger polarity selector switch
This switch can select the polarity (nega-
tive or positive) of a trigger pulse.
9 75 Ω termination selector switch
0 Selection DIP switch
Switches 1 to 4:
Selects the shutter speed.
Switch 5: Selects the frame or field
Switches 6 to 8:
Selects the normal shutter,
external trigger shutter, and
restart/reset.
A GAIN switch
A: Outputs a fixed-level video signal
according to the brightness of a
subject. (Variable range: 0 to 18 dB)
F: Fixed gain 0 dB
M: Variable gain (Manual)
M (during factory setting):
Adjusted so that all XC-ST50/50CEs
or XC-ST30/30CEs are the same in
sensitivity (set by Sony's standard
value) according to the deviation in
sensitivity of CCD.
Valid when multiple XC-ST50/50CEs
or XC-ST30/30CEs are used for an
identical subject.
B Volume control switch
This switch can be changed in the range
of 0 to 18 dB when the GAIN switch is set
to "M".
During factory setting, this switch is
adjusted to the fixed sensitivity for a
standard subject.
XC-ST50/50CE
XC-ST30/30CE
5