Table of Contents
Advertisement
6
REMOTE CONTROL UNIT
Names and Functions of Remote Control Unit Buttons
2
Buttons not explained here function in the same way as the
corresponding buttons on the main unit.
EJECT button
(play) button
1
Press this button to start
playback or recording.
(pause) button
3
Press this button to stop
playback or recording
temporarily.
(stop) button
2
REC (recording) button
8
and
9
(automatic
search reverse and forward)
buttons
Use this to find the beginning
of a track. (See Page 11.)
6
and
7
(manual search
reverse and forward) buttons
(See Page 11.)
REPEAT button
Press this button to play a single
track or all tracks repeatedly.
(See Page 13.)
RANDOM button
Press this button to play the track
in random order. (See Page 12.)
TITLE button
Press this button to switch the
time display to the title display.
CHARACTER button
8
NOTE:
• When the DMD-F101 is con-
nected in a system with the
D-F101 series, the DMD-
F101's power cannot be
switched between the on and
Power operation switch
standby modes using the
power button on the remote
Press this button to switch the
control unit.
power between the on and standby
modes.
1 to 10 (number) buttons
Use these buttons for direct
search and programmed
playback.
+10 button
Use this button to enter track
numbers of 11 or over for direct
search and programmed
M
playback.
EJECT
POWER
CALL button
1
2
3
Use this button to check the
4
5
6
programmed tracks.
During group playback,
switches between group
7
8
9
display mode and track display
mode. (See Page 19.)
10
+10
CALL
GROUP/PROG/DIRECT
CLEAR
GROUP
(group/program/direct) button
PROG/
DIRECT
Press to switch group playback,
program setting/playback and
REPEAT RANDOM
EDIT
ENTER
direct playback.
Normally this is set to the direct
TITLE CHARACTER
TIME
search mode. (See Page 12.)
CLEAR button
REMOTE CONTROL UNIT RC-282
EDIT button
ENTER button
TIME button
• Press this to switch the time
display between the elapsed
time and the remaining time
per track.
• When pressed in the stop
mode, the time display
switches between the total
playing time and the
recordable time.
(1) Inserting the batteries
The included remote control unit (RC-282) can be used to operate the DMD-F101 from a distance.
2
q Remove the remote control unit's back lid.
w Insert the two R6P (AA) batteries in the battery
compartment, in the direction indicated by the marks
inside the compartment.
e Put the back lid back on.
(2) Using the remote control unit
Approx. 7 meters
30˚
30˚
• Point the remote control unit at the remote sensor as
shown on the diagram when operating it.
• When the DMD-F101 is connected in a system with the
D-F101 series, the remote control signals for all the
system components are received at the remote sensor
of the receiver (DRA-F101).
NOTES:
• The remote control unit may not operate if the remote
sensor is exposed to direct sunlight or strong artificial
light, or if there is an obstacle between it and the
remote sensor.
Cautions on batteries
• Use R6P (AA) batteries in the remote control unit.
• The batteries should be replaced with new ones
after approximately one year, though this depends
on the frequency with which the remote control unit
is used.
• Even if the batteries are less than a year old, replace
them with new ones if the remote control unit no
longer operates even from a short distance from the
main unit.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting new batteries, wait about two
minutes after removing the old batteries before
inserting the new ones.
• Be sure to set the batteries in the proper "<" and
">" directions, as indicated by the marks in the
remote control unit's battery compartment.
• Remove the batteries when not using the remote
control unit for long periods of time.
• To avoid explosions and fluid leakage:
• Do not use one new battery with one old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
• If the battery fluid should leak, wipe all the fluid off
the battery compartment, then insert new batteries.
ON /
STAN
DBY
POW
ER LOAD
ING
MEC
HANI
SM
1 3
1
L
dB
-60 40
R
-30
-20 -12
INPU
-6 -2
T
MEMO
0
CHAR
REC
/
ACTE
R
EDIT
CD SRS
MULT
I REC
REC
-
LEVE
/ ENTE
L
+
R
MIN IDIS
C REC
ORD
ER DMD
-F10
1
• The remote control unit can be used from a straight
distance of about 7 meters, but this distance will be
shorter if the there is an obstacle in the way or if the
remote control unit is not pointed directly at the remote
sensor.
• Use the remote control unit within a range of 30° to the
left and right of the remote sensor.
• Do not press buttons on the main unit and on the
remote control unit at the same time. Doing so will
result in malfunction.
Hide quick links:
Advertisement
Table of Contents
