Connections - Denon DMD-F101 Operating Instructions Manual

4

CONNECTIONS

Connecting to the D-F101 Series
When connecting to a receiver other than the D-F101, there is no need to make connection 3. Note that in this case
2
none of the system functions (auto power on, etc.) will work.
• System operations such as the auto power on function
can only be used if stereo audio cords and system cords
are connected between all the system components. Be
sure to securely connect all the connection cords
between all the units.
• Disconnecting a system cord during system operation
may result in malfunction. Be sure to unplug the power
cords before changing the connections.
Power plug
AC 230 V, 50 Hz
(Plug into a power outlet)
Power plug
(for U.K. model)
Receiver (DRA-F101)
FM COAX. AM LOOP ANT. 1 2 SYSTEM R L
75
CONNECTOR
ANTENNA
+
L INPUTS TAPE MD
PRE
OUT
-
AC OUTLET
230V
SWITCHED
SPEAKER SYSTEM
R
SUB
SPEAKER IMPEDANCE 4~16
PHONO CD DVD/AUX PB REC PB REC WOOFER
Cassette deck (DRR-F101)
• Install the components in such a way that the ventilation
holes of the receiver (DRA-F101) are not obstructed.
• Use the AC OUTLET for audio equipment only. Do
not use them for hair driers, etc.
MD recorder (DMD-F101)
50Hz
W MAX
CD player
(DCD-F101)
Plug into the open SYSTEM CONNECTOR jack of another
component. Any SYSTEM CONNECTOR jack is OK.
Connect the DMD-F101's LINE OUT jacks to the
1
receiver's PB MD jacks using the included stereo
audio cord.
Connect the DMD-F101's LINE IN jacks to the
2
receiver's REC MD jacks using the included
stereo audio cord.
Connect the DMD-F101's SYSTEM
CONNECTOR jack (1 or 2) to the SYSTEM
3
CONNECTOR jack (1 or 2) of one of the other
components using the included system cord.
Connect the DMD-F101's optical digital input
terminal (DIGITAL OPTICAL IN 1 or 2) to the
4
digital output terminal of the CD player using
optical connection cord.
Plug the power cord into a receiver's AC outlet or
5
CD player's AC outlet.
The DMD-F101 can also be used when connected
to a receiver other than the one in D-F101 series. In
this case, none of the system functions (auto
power on, etc.) will work.
1 3
(DMD-F101)
POWER LOADING MECHANISM
ON / STANDBY
INPUT MEMO REC /
CHARACTER
18T r0 2 m 4 6 s
-
L
1 REC LEVEL
dB -60 40 -30 -20 -12 -6 -2 0 / ENTER
R
MINIDISC RECORDER DMD-F101
(DCD-F101)
ON / STANDBY
REPEAT
TRACK
COMPACT DISC PLAYER DCD-F101
For heat dispersal, leave at least 10 cm of space between the top, back and sides of this unit and the wall or
other components.
10 cm or more
1 3
POWER LOADING MECHANISM
ON / STANDBY
INPUT MEMO REC / EDIT CD SRS
CHARACTER
18T r0 2 m 4 6 s
- +
L
1 dB -60 40 -30 -20 -12 -6 -2 0 REC LEVEL
R / ENTER
MINIDISC RECORDER DMD-F101
NOTES:
• Do not plug power cords into power outlets until all
connections have been completed.
• Check the left and right channels and be sure to
interconnect them correctly (L to L, R to R).
• Plug in the power cords securely. Incomplete
connections will result in noise.
• Clasping the power cords and connection cords
together may result in humming or noise.
• After unplugging the power cord, wait at least 5
seconds before plugging it back in.
Recommended System Installation
• To ensure performance and stability, install the D-F101
series as shown below.
• Do not place another component directly on top of the
receiver (DRA-F101).
• For stability, do not stack more than three components
on top of each other.
(DRA-F101) MEMORY TUNING
FUNCTION TONE TIMER RDS / SET DOWN UP BAND
SYSTEM
ON / STANDBY
EDIT CD SRS MULTI REC
PHONES
+
(DRR-F101)
e
ON / STANDBY
DOLBY NR
CD SRS REC 0 PLAY 1
ON
OFF
5 cm
MULTI REC
VOLUME
SOURCE
DIRECT
AM-FM STEREO RECEIVER DRA-F101
PLAY
CD SRS REC
REVERSE
MODE
CASSETTE DECK DRR-F101
5