Pick Rec Function - Denon DMD-F101 Operating Instructions Manual

15

PICK REC function

• PICK REC is a function you can pick only the pieces of audio program you want to store on the disc, while listening to audio
programs, since the PICK REC recording starts. If you operate before the TOC writing, you can store also all the audio programs
during the PICK REC recording.
• The time for which PICK REC recording is possible is the remaining recordable time on the disc.
1. Starting the PICK REC function
(Main unit)
ON / STANDBY
1
PICK
PICK REC indicater
Perform steps 1 to 6 under "(1) Analog recording" on page 14. (For digital recording, perform steps 1 to 6 under "(2)
Digital recording" on page 15.)
Press the MULTI REC button twice.
1
• " Pick Rec " is displayed and the PICK REC indicator flashes.
Use the jog dial to adjust the recording level.
2
• Adjust the REC LEVEL control so that the "OVER" indicator does not light even when the volume is loudest.
After adjusting, set the source to be recorded to the standby mode.
Press the (play/pause) button.
1 3
3
• The PICK REC indicator lights.
• The PICK REC operation starts and the time for which PICK REC recording is possible is displayed.
To record the track during the PICK REC mode, press the ENTER button before the end of the track is reached.
• The PICK REC indicator flashes and that track is recorded.
4
• When the track number changes, the PICK REC indicator stops flashing, remaining lit, and the new track is
not recorded.
If you do not wish to record that track, do not perform any operation.
5
• Tracks at which the PICK REC indicator is lit are not recorded.
• When the operation in step 1 is performed in the middle of a track, it is not possible to record that track from the
beginning.
• During the PICK REC operation, the track number may change in the middle of the piece of music. Perform the
operation in step 4 for all the tracks you want to record.
• To cancel recording after performing the operation in step 4, press the ENTER button again before the track
number changes. The PICK REC indicator stops flashing, remaining lit, and that track is not recorded.
• During the PICK REC operation, check the time for which PICK REC recording is possible on the display. (Pay
attention to the amount of time remaining.)
• The stop mode is set automatically once the time for which PICK REC recording is possible is up. Finish writing
the data on the disc using the procedure described in "2. Stopping the PICK REC function" on Page 29.
• Recording cannot be selected if the track number reaches above 35 after the PICK REC operation is started, even
if there is still time remaining. (The PICK REC indicator flashes twice.)
3 1
1 3
POWER LOADING MECHANISM
INPUT MEMO REC / EDIT CD SRS MULTI REC
CHARACTER
18T r0 2 m 4 6 s
- +
L
REC LEVEL
dB -60 40 -30 -20 -12 -6 -2 0
R / ENTER
MINIDISC RECORDER DMD-F101
2,4
2. Stopping the PICK REC function
• When stopping the PICK REC function, be sure to perform the operation described below to write the data on the
disc.
(Main unit)
ON / STANDBY
1
Press the (stop) button.
2
• Recording stops and the PICK REC indicator turns off.
1 • " P. Rec OK? " is displayed.
• In addition, once the time for which PICK REC recording is possible is up, the stop mode is set automatically
and " P. Rec OK? " is displayed.
(If the tracks to be recorded have been properly picked)
Press the ENTER button.
• " P. Rec Edit " is displayed.
2
• Only the tracks for which "record" was selected during the PICK REC mode are stored on the disc.
• Do not perform any other operation while " P. Rec Edit " is displayed, or the recording may be lost or
may not be properly stored on the disc.
• The TOC data is written once the " P. Rec Edit " display turns off.
(If the tracks to be recorded have not been properly picked)
Press the (stop) button.
2
3
• " P. Rec Cancel " is displayed.
• All the tracks played since the PICK REC mode was set are stored on the disc.
• If the power is set to the standby mode by pressing the power operation button during the PICK REC mode, all
the tracks played since the PICK REC mode was set are stored on the disc.
• The " P. Rec OK? " display may appear if the PICK REC mode is canceled several seconds after it is set, but it
may happen that no track has be recorded.
NOTE:
• When writing the TOC data starts, " " indicator flashes. Do not subject this unit to shocks or unplug the
power cord while the data is being written, or the recording may be lost or may not be properly stored on the disc.
1
1 3
POWER LOADING MECHANISM
INPUT MEMO REC / EDIT CD SRS MULTI REC
CHARACTER
18T r0 2 m 4 6 s
- +
L
REC LEVEL
dB -60 40 -30 -20 -12 -6 -2 0
R / ENTER
MINIDISC RECORDER DMD-F101
2
29