Related Manuals for Peak Pilates MVe Reformer Tower Conversion Kit
Summary of Contents for Peak Pilates MVe Reformer Tower Conversion Kit
- Page 1 Reformer Tower Conversion Kit ® Reformer Tower Retrofit Kit ® Reformer Mat Set ® MVe_Tower_Owners_Manual-10_09.indd 1 12/4/09 4:21:16 PM...
-
Page 2: Recommended Use
Use only components provided by the manufacturer. Do not use parts or accessories or modify the machine in any way not approved by Peak Pilates. Keep a three foot area (about one meter) around the equipment clear of obstructions. -
Page 3: Warranty
Upholstery, straps, and loops are warranted against defects in workmanship and/or materials for 60 days. This warranty refers to the Peak Pilates MVe Reformer Tower Kit and covers materials only. It remains in effect only under the following conditions: This machine is not modified in any way. - Page 4 Tower Conversion Kit Components ITEM # DESCRIPTION Tower Assembly Push Through Bar w/2 Quick Release Pins Arm Springs w/Double Ended Clips (Qty: 2) Roll Down Bar Safety Chain w/2 Safety Links Foot Loops Push Through Bar Storage Strap Push Through Bar Spring w/Quick Snap Clip and Safety Link Push Through Bar Sleeve Leg Springs w/Double Ended Clips (Qty: 2) Lower Tower Connecting Tubes (Qty: 2)
- Page 5 Mats Foot End Mat Head End Mat Hardware Packs Connector Tube Hardware Pack 8mm x 80mm long Button Head Cap Screw (Qty: 8) 8mm x 50mm long Button Head Cap Screw (Qty: 2) 8mm x 30mm long Button Head Cap Screw (Qty: 2) 8mm Hex Nut (Qty: 8) 8mm Washer (Qty: 20) Tower Mounting Hardware Pack...
-
Page 6: Tools Included
Retrofi t Kit Additional Components Head End Cross Member Head End Leg Tools Included Combination Tool #2 Phillips Screwdriver 13mm Wrench 17mm Wrench 6mm Allen Wrench (Note: Only used for retrofi t) 5mm Allen Wrench MVe_Tower_Owners_Manual-10_09.indd 6 12/4/09 4:21:19 PM... - Page 7 Assembly Check to see whether the unit you have includes the mounting brackets for the MVe Tower. If so, proceed from step 2 below. If not, skip to the section titled: “MVe Tower Retrofit Procedures”. Tools required: 5mm Allen Wrench and pliers or 13mm open end wrench.
- Page 8 Assembly (continued) Push one of the provided black plugs into each of the holes in the Head End Wood once the Risers are removed. Route the Ropes through the Pulleys on the Tower Risers and through the Rope Cleats. Excess Rope can be dropped in the holes located immediately in front of the Cleats.
- Page 9 Assembly (continued) Push Through Bar Spring and Safety Chain: The Push Through Bar (PTB) Spring is similar to the Reformer Springs in length and diameter but is distinguished by having a closed loop at each end. The PTB Spring includes a vinyl sleeve to protect the unit from being abraded.
- Page 10 Tower Retrofit Procedures ® Remove the ropes from the MVe Reformer and place on the side. Withdraw the Pull Pin for the Risers and completely remove the Riser/Pulley Assembly from the machine. Note: The old Risers will no longer be used.
- Page 11 Tower Retrofit Procedures (continued) ® Tool required: #2 Phillips Head Screwdriver Looking inside, locate and remove the three wood screws that are used to assemble the plastic Head End Cap to the Frame. With the help of an assistant, place the machine back to its upright position.
- Page 12 Tower Retrofit Procedures (continued) ® Tools required: 5mm Allen Wrench The Head End Cross Member is assembled using three screws on each of its Mounting Flanges. Locate all 6 screws. The screws identi- fied as ‘A’ in the accompanying illustration need to be completely removed.
-
Page 13: Adjusting The Risers
Operating the MVe Reformer Tower ® Adjusting the Risers The Risers have 12 scaled positions and 1 storage position. The Riser positions are scaled so both Risers can be easily adjusted to the same height. To adjust the Risers: Pull the Riser Pull Pin and move the Riser up or down to the desired position. - Page 14 Converting to Mat—with or without Tower (continued) To convert to Mat: Pull the Release Levers for the Shoulder Pads and fold the Pads to the Carriage. Remove the Reformer Springs from the Gear Bar and roll the Carriage toward the Head End of the machine.
- Page 15 Converting to Mat—with or without Tower (continued) Rev 1 or Rev 2 (round Gear Bar), without Tower: Follow Steps 3(a) and 3(b) above Retract the Pull Pins, completely remove, and drop the Risers into the well of the unit. Skip to Step 7. No Rev units (oblong Gear Bar), with Tower STEP 4b Place the Gear Bar in position 3.
- Page 16 Converting to Mat—with or without Tower (continued) Place the mat with the Foot Strap (Foot End Mat) onto the rails at the Foot End of the machine. Make sure that the Strap is exposed and rests on the Foot End plastic cap. Push the mat as far towards the foot end of the machine as possible.
- Page 17 Maintaining the MVe Reformer and Tower ® You have purchased a high quality piece of equipment that is constructed of the finest components and materials. Proper care requires only a small, but very important investment of time in a routine maintenance program. Maintenance procedures follow the same guidelines provided in your original MVe Reformer manual.
- Page 18 Maintaining the MVe Reformer and Tower (continued) ® Clean: Framework: The framework and wood components should be cleaned with a mild, soapy solution. A good furniture polish can also be used on the wood platforms. Upholstery: We recommend wiping down your vinyl upholstery with a mild cleaning solution after each use. For example, a solu- tion of 1 part Simple Green and 12 parts water in a spray bottle can be used.
- Page 19 Contact Information: Peak Pilates 5555 Central Avenue, Suite 200 Boulder, Colorado 80301 303.998.1531 (Worldwide) (+1) 800.925.3674 (North America) (+1) 303.473.9142 (Fax) MVe_Tower_Owners_Manual-10_09.indd 19 12/4/09 4:21:34 PM...