Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ADS-tec MCR5000
Summary of Contents for ADS-tec MCR5000
-
Page 1: User Manual
Version User Manual Industrial PCs MCR5000... - Page 2 Industrial PCs MCR5000 Product Portfolio Copyright ads-tec GmbH Heinrich-Hertz-Str. 1 D-72622 Nürtingen Germany © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 3: Table Of Contents
IEEE1394 Firewire 4-pin connection (without power) ............27 Network connection (RJ45) ....................27 COM (RS232) Serial Interface ....................28 Optional radio network card ....................28 DVI interface ..........................29 AUDIO L / R ..........................30 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 4 Technical details ..................... 34 Computer data ......................... 34 General data..........................35 Service and Support ....................36 ads-tec Support ........................36 Company Address ........................36 Battery replacement ....................37 Fuse replacement ....................41 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 5: About Us
E-Mail: mailbox@ads-tec.de Home: www.ads-tec.com ads-tec GmbH provides large enterprises and globally active corporations with cutting edge technology, up-to-date know-how and comprehensive services in the area of automation technology, data processing technology and systems engineering. ads-tec GmbH implements full automation solutions from planning to commissioning and is specialized in handling and material handling technologies. -
Page 6: Remarks
The texts, data and images herein are not binding. The right to any subsequent amendment and/or variation due to any technical and engineering progresses in the art whatsoever is hereby reserved. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 7: Trademarks
Reproduction, translation, as well as electronic and photographic image storage and/or amendment processes, are subject to prior written authorisation directly by M/s. ads-tec GmbH. Any violation and infringement thereto will be held liable for compensation of all damages. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 8: Environmental Conditions
1.6 E NVIRONMENTAL CONDITIONS The device may be operated under the following conditions. Failure to observe these specifications will terminate any warranty for this device. Ads-tec cannot be held liable for any damages arising due to improper use and handling. ... -
Page 9: Scope Of Delivery
The optional cable set might include the following individual cables: 1 x Rubber power lead 1 x Rubber power lead extension for monitor / display 1 x DVI cable 1 x Serial null-modem cable © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 10: Operating Instructions
Should the service system have evident signs of damages incurred e.g. due to wrong operation or storage conditions or due to improper unit use, the unit must be decommissioned or scrapped. Ensure that it is safe from accidental re-implementation. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 11: Warranty / Repairs
All unit assembly operations must be strictly conducted only under safe, secure and zero-potential conditions. Special Note: When handling parts and components susceptible to electrical discharge, please accurately observe all the relevant safety provisions. (DIN EN 61340-5-1 / DIN EN 61340-5-2 refers) © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 12: Assembly
Industrial PCs MCR5000 SSEMBLY 3.1 O VERALL EVICE IMENSIONS © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 13: Order Of Installation
(0° with DVD operation!) Observe the monitor data sheet! Note: The maximum torque for fixing the MCR 5000 installation screws is 5 Nm for wall- mount installation. Tighten screws evenly. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 14 Respective retainers must be installed above the MCR 5000 device. As soon as the retainers have been installed, the device should be secured with these brackets or retainers (as it can be seen in the figure, for example). © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 15 The 6 screws together with their washers will directly beneath the screw head be put through holes drilled in the wall, screwed into the blind-rivet nuts in the MCR 5000 device, and subsequently tightened with a torque of 5 Nm. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 16 For removing the installation bracket it is required to unhinge the previously attached brackets or retainers. In this case, the MCR 5000 must be supported by another person. The installation plate is unhinged after removing both safety screws from the MCR 5000. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 17 All six screws must be used for fixing the installation bracket. Warning: The permissible thread depth of the fixing screws inside the monitor case has to be checked before installing the bracket on the monitor. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 18 Vertical installation: Warning: The installation adapter must always be attached in the centre with both installation methods. Verify if vertical operation is permitted for your display unit. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 19 MCR 5000 case when attaching the monitor. Subsequently, the monitor must be pushed beyond the retainer lobes. Make sure that the installation bracket is flush with the MCR 5000 unit after installation. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 20 Industrial PCs MCR5000 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 21 The installation bracket is screwed to the MCR 5000 case by using the previously removed fixing screws (M6x10mm). Warning: The monitor must still be supported by two persons until both components are safely connected. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 22 The locking plate is pushed into the provided holes by using both tabs, as shown in the figure, and finally pushed into the device until the lock snaps audibly and noticeably into place. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 23: Commissioning
The screen of a data cable must always be connected with the connector housing (EMC). Note: Under the embedded operating system, interfaces must explicitly be enabled and required drivers must be installed for being able to use them. 4.1 A VAILABLE INTERFACES © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 24: Cable Installation
Depending on the colour and type of flashing different device states are displayed by the SYS LED. The following signals are displayed: LED lights green The device is ready for operation. (Power ON) LED is off The device is switched off. (Power OFF) © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 25: Interfaces
Max. switch-on current: 100A (230V AC) Warning: The load at the switched AC power supply output must not exceed 500W. AC out: Max. 5A / 100V, max. 2.1A / 240V © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 26: Usb Connections
The cover has a tab on the right, which is used for protecting the USB connection. Note: All USB interfaces available meet the USB 2.0 standard. 5.3 S ISO 7816 EADER ACCORDING TO The SIM card reader is currently under preparation for future use. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 27: Ieee1394 Firewire 4-Pin Connection (Without Power)
You can install the drivers required for functioning from the enclosed service CD, should they not be installed on the device. PIN NUMBER SIGNAL NAME TX + TX - RX + RX - © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 28: Com (Rs232) Serial Interface
Devices from ads-tec including wireless LAN are equipped with a Mini-PCI WLAN card including Atheros chips. If a device is delivered including operating system by ads-tec, all required device drivers will also be integrated in the system. Under the "Windows XP Professional" and "Windows XP Embedded"... -
Page 29: Dvi Interface
Ground (for +5V) Hot Plug Detect TMDS Data0- TMDS Data0+ TMDS Data0/5 Shield TMDS Clock Shield TMDS Clock+ TMDS Clock- Analogue Red Analogue Green Analogue Blue Analogue Horizontal Sync Analogue GND Return:(analogue RGB) © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 30: 5.9 Audio L / R
Industrial PCs MCR5000 5.9 AUDIO L / R © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 31 The integrated stereo speakers may be enabled or disabled by using the "Internal Speaker Control" extension module. You'll find a detailed documentation for installation of this extension module on the service CD supplied with the equipment. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 32: Drives
Note: The DVD drive is of the slim-line drive type. Warning: If the device includes a DVD drive, this drive may only be operated perpendicular to the installation position. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 33: External Drives
USB interfaces, to which an external drive could be connected. Warning: Removing an external drive during the reading/writing process is not permitted. Data loss or damage could be the result if this is not observed! © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 34: Technical Details
As an option: WLAN card incl. 2 integrated antennas Power supply 100V / 240V AC via rubber connector and power supply circuit breaker, incl. shared fuse (max. value of 500W) ON / OFF / SUSPEND-ACPI pushbutton © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 35: General Data
(DIN EN 60068-2-27) Vibrations 1 G, 10 … 150 Hz In operation (DIN EN 60068-2-6) EN 61000-6-3:2001 + A11:2004 EN61000-6-2:2005 A corresponding CE-conformity declaration can be delivered by the manufacturer on request. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 36: Service And Support
In any such case, maintenance and support is provided solely by the partner company that supplied the device or unit. -
Page 37: Battery Replacement
If a TFT or plasma display has been installed, disassembly should be carried out by at least two persons. Also make sure, that the TFT or plasma display is sufficiently supported in order to avoid falling after loosening. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 38 ATTERY COMPARTMENT LOCATION The location of the battery compartment is highlighted in the figure. PENING THE BATTERY COMPARTMENT 1) Remove safety screw from battery compartment lid by using a suitable screw driver. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 39 There is a risk of explosion if the battery is replaced with the wrong type or with the wrong polarity. Adhere to the valid regulations for environmentally-friendly disposal of batteries if the battery has reached the end of its life cycle. SSEMBLY © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
- Page 40 MCR 5000 casing. Observe the required security measures when attaching the installation adapter. You can find information about design 5000 device incl. TFT or plasma display in more detail in the user manual. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 41: Fuse Replacement
EPLACING THE FUSE You can now remove the fuse from the fuse retainer and replace it with the same type of fuse. The type of fuse to be used is: Vendor: Littelfuse © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 42 Activate the locking mechanism by using a suitable tool (screw driver) and slightly pushing the fuse retainer in while twisting it into its initial position. Make sure to check that the fuse retainer is properly positioned. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...