Jensen JMC-1250 User Manual page 5

BATTERY INSTALLATION
The battery compartment is located on the
back of the remote control.
1. Remove the battery compartment door
by pressing in on the tab and lifting it off.
2. Insert two AAA size batteries (not
included) into the battery compartment
following the polarity markings inside the
battery compartment.
3. Replace the battery compartment door.
BATTERY WARNING
1. Be sure that the batteries are installed correctly. Wrong polarity may damage
the unit.
2. Use only the size and type of batteries specified.
3. Do not mix old and new batteries.
4. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
5. If the unit is not to be used for an extended period of time, remove the batteries.
Old or leaking batteries can cause damage to the unit and may void the
warranty.
6. Do not try to recharge batteries not intended to be recharged; they can
overheat and rupture. (Follow battery manufacturer's directions).
7. Do not dispose of batteries in fire, batteries may leak or explode.
GETTING STARTED
1. Connect the speaker wires to the speaker terminals (#36) located on the back
of the unit.
2. Plug the AC POWER CORD (#39) into a 120V AC ~ 60Hz outlet.
3. The unit will go into standby mode. The STANDBY LED INDICATOR (#5) will
turn on.
4. Press the POWER ON/STANDBY BUTTON (#7) once to turn on the JMC-1250.
The STANDBY LED INDICATOR (#5) will turn off.
Press POWER ON/STANDBY BUTTON (#7) again to turn off the JMC-1250.
The STANDBY LED INDICATOR (#5) will turn on.
SETTING THE CLOCK
The clock has to be set before using the system for the first time. When you plug
the system into an AC outlet for the first time, the LCD DISPLAY (#2) will show
12:00 and need to be set.
1. Press MEMORY / CLOCK-ADJUST BUTTON (#14), the Hour digits will flash.
Press OR BUTTON (#12 or #28) to select the correct hour. Press the
MEMORY / CLOCK-ADJUST BUTTON (#14) to confirm.
2. The Minute digits will flash, Press
correct minute. Press the MEMORY / CLOCK-ADJUST BUTTON (#14) to
confirm.
3. Press and hold the STOP BUTTON (#8) to change 12/24 hours clock display.
Note : The clock settings may be lost if the main power switch is turned off. If this
occurs, you will need to reset the clock
LISTENING TO THE RADIO
1. Press the POWER ON/STANDBY BUTTON (#7) to turn on the JMC-1250.
2. Press the TUNER/BAND BUTTON (#25) repeatedly to enter tuner mode and
desired band. The radio frequency will show on the LCD DISPLAY (#2).
3. Press and hold the button (#28) or
previous available station. If the reception is poor, try Manual Tuning to fine-
tune the station.
4. Press the button (#28) or button (#12) briefly to manually tune through
the frequency band.
5. Adjust the volume control to the desired volume level.
6. Press the POWER ON/STANDBY BUTTON (#7) to turn the JMC-1250 to
standby mode after listening.
Setting the Radio Station Presets
The JMC-1250 allows you to store up to 40 station presets ( AM-20 and FM-20 )
for easy recall at any time.
1. Press the POWER ON/STANDBY BUTTON (#7) to turn on the JMC-1250.
2. Press the TUNER/BAND BUTTON (#25) repeatedly to enter tuner mode and
select FM band.
3. Tune to the radio station you want to store in memory.
4. Press MEMORY / CLOCK-ADJUST BUTTON (#14), the preset number "00"
the
will be flashing on display.
5. Press +10 / PRE-UP BUTTON (#29 or -10 / PRE-DN
select the desired preset number ( 00–20 ).
6. Press MEMORY / CLOCK-ADJUST BUTTON (#14) to confirm.
the
7. To store up to 20 stations presets, repeat steps 3 to 6 above.
8. Press the TUNER/BAND BUTTON (#25) repeatedly to enter tuner mode and
select AM band.
9. To store up to 20 stations presets, repeat steps 3 to 6 above.
E-8
OR BUTTON (#12 or #28) to select the
button (#12) to search for the next /
BUTTON (#13) to
E-9