Cleaning Of The Dvd Player; Disposal; Troubleshooting - Silvercrest KH 6517 Operating Instructions Manual

15. Cleaning of the DVD player

Clean the housing of the DVD player with a slightly damp cloth and a mild
cleanser only. When cleaning, make sure that no moisture gets into the DVD
player!
Clean the inside of the disc tray, if necessary, exclusively with a clean dry
brush (i.e. a lens brush obtainable from a photographic dealer). Never clean
the inside of the disc tray with anything moist!
Warning!
Moisture penetrating into the DVD player creates the risk of an electric
shock! The DVD player may also be irreparably damaged!

16. Disposal

Disposing of the appliance
Do not, under any circumstances, discard the appliance in the house-
hold refuse.
This appliance is subject to the European Guidelines 2002/96/EG.
Dispose of the appliance through an approved disposal centre or at your
community waste facility.
Observe the currently applicable regulations. In case of doubt, please
contact your waste disposal centre.
Disposing of batteries!
Do not dispose of the batteries with household waste. Every consumer is legally
obliged to dispose of batteries at a collection site of his community/city district
or at a retail store.
This obligation is intended to ensure that batteries are disposed of in an en-
vironmentally safe fashion.
Only dispose of batteries when they are fully discharged.
Disposal of packaging
Dispose of the packaging materials in an environmentally responsible
manner.

17. Troubleshooting

Display is blank/DVD player shows no functions even though it is
switched on
A
Check to see that the power cord is properly plugged into the power
socket.
B
Check to make sure that there is power at the power socket, in which
you have plugged the DVD players power cord, by connecting another
appliance to the socket. If necessary plug the DVD players power cord
into another power socket.
C
Check to make sure that the display is not switched off by the Dimmer
function. To do this press the
D
Switch off the DVD player by pressing the
conds. Then switch the DVD player back on by pressing the
ton.
The display shows "No Disc" even though there is a disc inserted
A
The disc is dirty, scratched or damaged. Clean the disc or insert another
disc.
B
The Country/Region code on the inserted DVD/VCD/S-VCD does not
correspond to the Country/Region code of the DVD player. In this case
the DVD/VCD/S-VCD cannot be played with the DVD player.
Inserted disc will not playback
It is possible that a layer of condensation has built up on the DVD players
laser scan lens. This can be the case especially if the DVD player has been
subjected to strong temperature fluctuations.
If this is the case place the DVD player in a dry environment at normal room
temperature. First remove the currently inserted disc from the disc tray. Then
leave the DVD player switched off for at least one hour without using until the
condensation film has evaporated.
No image or Black/White image only
A
Check to make sure that all connection cables between the DVD player
and the television (or Video projector) are firmly inserted into the corres-
ponding sockets
B
Check to make sure that the settings in the OSD menu match the connec-
tions variant, with which you have connected the DVD player to the tele-
vision (or Video projector).
For this see chapter 8. "Connecting the DVD player to a television".
C
Check by means of the televisions (or Video projectors) operating in-
structions to see if settings to the television (or Video projector) may be
necessary in order to use the DVD player with the television.
No sound
A
Check to see if the television and/or the DVD player has been switched
to mute.
B
Check to see that all connecting cables between the DVD player and
potentially connected audio components are firmly plugged into the
corresponding sockets
C
Check to make sure that the settings in the OSD menu match the connec-
tions variant, with which you have connected the audio component to
the DVD player.
For this see chapter 9. "Connecting an audio component to the
DVD player".
- 24 -
DIMMER
button on the remote control.
POWER
button and wait ten se-
POWER
but-