Advertisement
Quick Links
Advertisement
Related Manuals for Kohler CFI230G
Summary of Contents for Kohler CFI230G
- Page 1 CFI230G Indigo Quadrant Enclosure with integrated Mira Magna Shower System (646) Slide Rail Fixed Head Kohler Daryl Limited Alfred Road, Wallasey, Wirral, CH44 7HY England Fitting Instructions Tel 44 (0)151 606 5000 Fax 44 (0)151 638 0303 www.daryl-showers.co.uk E-mail Daryl@daryl-showers.co.uk...
- Page 2 For over 80 years, Mira Showers have had the same reputation for shower systems. Your new showering product has been created by these two specialist organisations from within the same leading world-wide bathroom company Kohler. They are both bound by the same values of delivering beauty, quality, innovation, reliability and service.
-
Page 3: Table Of Contents
We recommend that the unit is installed by a qualified Plumber or Engineer. Please retain this document for future reference. Note: Due to our desire to always improve our products, Kohler Daryl reserve the right to change specification without prior notice... -
Page 4: Components
Nylon Grub Door Screw To avoid limescale, use your thumb or a soft cloth to wipe any limescale from the soft rubber nozzles and the front face of the showerhead. Fixed Roller Splashguard CFI230G CFI230G... -
Page 5: Troubleshooting
Digital Mixer Valve malfunction Maximum temperature Incorrect shower incorrectly set temperature Digital Mixer incorrectly fitted CFI230G Roller Securing Caps Remedy Check water supply Fixed Head Water Delivery Check cable connections System Check electrical supply Isolate product and turn... -
Page 6: Enclosure Installation
Adjust wall jamb until glass is parallel to the Remove wall channel from jamb and place edge of the tray ‘A’. When jamb is vertical mark edge of wall channel on the wall ‘B’. STEP CFI230G the tray ‘B’ STEP against mark on wall STEP... - Page 7 - Water flows from the outer set of holes at a reduced flow rate. To select the Economy setting, turn the spray plate fully clockwise. CFI230G Check the wall channel is vertical and mark Fit the splash guard to the bottom of the panel. through the holes ‘A’...
- Page 8 The glass should be 2mm lower than the top of the wall jamb. Tighten screws ‘A’ when the glass is in the correct position STEP CFI230G Check glass is vertical. If not remove screws, re-drill and re-fit as required.
- Page 9 4.2. Enabling - Press and momentarily hold the Warm Up and Low keys at the same time.The two keys will flash twice and beep three times to confirm the selection is successful. CFI230G Carefully lift the assembly onto the tray. The end of the glass panel fits into slot ‘A’...
-
Page 10: Commissioning
Fit the splashguard to the bottom of the glass STEP CFI230G of the slot in the tray ‘B’. To adjust the glass 1. General it is the correct postion. Re-tighten screws 2. - Page 11 The lintel is supplied as a RH unit. For LH versions loosen the panel clamps and turn them through 180 Ensure glass panels STEP STEP STEP are parallel to each other Check top rail is level. Draw around parking block STEP CFI230G CFI230G...
- Page 12 When the lintel is level tighten screw ‘B’ on each panel clamp until it grips the glass. IMPORTANT - DO NOT OVER TIGHTEN Fit caps to lintel ‘C’ CFI230G Fixed Head Water Delivery Only 3. Drill holes with 6mm drill 4. Plug holes 7.
- Page 13 Water Delivery System at the top of the column. Caution STEP CFI230G Slider Rail Water Delivery Only Fit the fixed roller to the tray on the same side as Carefully lift the Water Note: The seal ‘A’ on the glass panel will need...
- Page 14 Whilst supporting the weight of the door slide Lift the glass door up and slide the rollers onto the bottom roller into the bottom track Caution STEP CFI230G Fit door retainers to both top roller brackets. the roller and plastic glass guide Caution STEP...