Assigning A New Id#; Reprogramming R2Lc Circuit Boards To Restore Features - Lionel K-LINE EP-5 Owner's Manual

Assigning your EP-5 a new ID#
A
s your fleet of Command-equipped Lio-
nels grows, you'll want to give your EP-5
a more individualized number. Choose from
any between 1 and 99. To make things easy,
use a portion of your EP-5's cab number.
Turn the Command Base ON and place the
EP-5 on track. Power up, then set the EP-5's
reverse unit control switch to PGM (see the
illustration on page 5). Using CAB-1, press
ENG, the locomotive ID# (you select: ?), then
press the SET button located under CAB-1's
removable panel. Hear the horn blow (or see

Reprogramming R2LC circuit boards to restore features

D
ue to the inevitable derailments, static, and the negative nature of electricity, it is possible
that your R2LC could someday lose its setup program. The symptoms of this condition
would be unresponsiveness in command mode. This can be easily remedied by "reprogram-
ming" your R2LC using the following steps.
STEP 1: Move switch on locomotive from
run to program.
STEP 2: Turn on Command Base.
STEP 3: Place locomotive on track, then turn
on power to track.
STEP 4: Press "ENG" then input locomotive's
ID#. Press "SET"
STEP 5: Press "ENG", then the ID#, "AUX1",
then press 8 for your locomotive.
The following Lionel marks may be used throughout this instruction manual and are protected under law.
All rights reserved.
Lionel , TrainMaster Lionel Lionel , TrainMaster , TrainMaster , TrainMaster , Odyssey
® ® ® ® ® ® ® ®
StationSounds , Pullmor , Pullmor , Pullmor , ElectroCoupler , Pullmor
TM TM TM
PowerMaster PowerMaster , Lionel ZW PowerMaster , Lionel ZW , Lionel ZW , Lionel ZW , ZW
® ® ® ®
©2008 Lionel L.L.C., Chesterfield, Michigan 48051-2493 UNITED STATES OF AMERICA
Printed in China
, Odyssey , RailSounds , Odyssey , Odyssey , RailSounds
® ® ® ®
, ElectroCoupler , Magne-Traction , ElectroCoupler , ElectroCoupler
® ® ® ®
, ZW , PowerHouse , ZW , ZW , PowerHouse
® ® ® ® ® ® ® ®
the headlight flash if Railsounds is off); that's
the R2LC confirming the new ID#. Set the
reverse unit control switch to RUN. Your EP-5
is ready for operations with its all-new ID#.
We recommend that you choose an easy to
remember ID# for your engine. Some pos-
sibilities are part of the engine road number,
your age, any two digit number that is not
used by another engine. Write the number on
a small piece of tape and put this on the bot-
tom of the fuel tank to aid in remembering.
STEP 6: Turn off power to track, wait ten
seconds.
STEP 7: Remove locomotive from track,
move switch from program to run.
STEP 8: Place locomotive back on track, turn
power on to track.
STEP 9: Press "ENG" and ID#, then operate
as normal.
, CrewTalk , CrewTalk , CrewTalk , TowerCom , CrewTalk , TowerCom
® ® ® TM TM TM TM
, Magne-Traction , CAB-1 Remote Controller , , CAB-1 Remote Controller , CAB-1 Remote Controller , CAB-1 Remote Controller
TM TM TM TM ® ® ®
, TMCC , Lionelville , TMCC , TMCC , TMCC , Lionelville
® ® ® ® ® ® ®
9
, DynaChuff , , DynaChuff , DynaChuff , DynaChuff
TM TM TM TM TM
, Lockon , Lockon
TM TM TM ®
® ®