Advertisement
To deactivate the timer function before the set time:
- Select the cooking zone (E) and press one of the two buttons (N). When the zone indicator (R) on display (E)
stops flashing, the function is no longer active.
Note: to display the residual cooking time, just press the cooking zone (E) of interest selection button.
• Minute Minder (Countdown):
Attention! This function can only be used if no cooking zone (E) has the Timer inserted.
- The Minute Minder allows to set an established countdown that goes from 1 to 99 minutes.
On expiry of the time, the hob emits an acoustic signal without changing the active functions.
- The function activates only if the cooking level is set at "0" on all displays (R).
- Press the Timer button (N) and set the time with the same procedure as the Timer function, with the unique
exception that the indicators (O) do not switch on.
Note: whenever the Timer is to be activated on at least one zone, the Minute Minder deactivates automatically.
To activate the Timer instead of the Minute Minder, proceed as follows:
1- Use one of the buttons to select (E) the cooking zone where the timer function is to be activated.
2- Set the cooking level by acting on the SLIDER control (D1).
3- Select the Timer button (N).
4- Select the button (E) again where the timer function is to be activated.
5- Select the Timer button (N).
6- Set the cooking time by acting on the SLIDER control (D1).
• Booster (Fig.2 - Fig.3 (S)):
Depending on the appliance model, it may be fitted with a Booster system which can be used to speed up
cooking times through the application of a power level which is greater than the nominal value, within a defined
period of time.
The cooking areas provided with this function are indicated by a letter (Z).
To activate the Booster, switch the interested cooking area on at any power level and press key S (Fig.2 - Fig.3).
This allows to reach higher temperatures in a short time disbursing the maximum power possible.
The letter P on the display indicates that the function is active. This will be displayed for about 10 minutes, then
the cooking area will automatically turn back to power level 9.
- The Booster may not activate if, the cooking zone (with the letter Z) has been previously activated with high
temperature levels.
- In order to use the Booster function, wait for the P on the display R to stop flashing and the temperature inside
the cooking surface to decrease.
• Integrated power control (Fig.4):
Each phase (this is divided into two zones in a vertical line: F1 e F2) is capable of using a maximum power of
3,700W.
If this is exceeded for example by activating the Booster, the software automatically lowers power of the previously
selected zone until it reaches the allowed power level.
The display of the zone with limited power will begin to flash for about 3 seconds. During this time it is possible
to modify the power level.
• Heat up (Fig.2 - Fig.3 (L1)) (Rapid heating):
The Heat up function can be used to set the cooking zone to its maximum temperature for a specified period
of time, after which the temperature will return to a lower value set previously.
To activate the Heat up function, select one of the cooking zones (E).
Set the cooking level at "9" by acting on the SLIDER control (D1), press Heat up (L1)and the cooking zone will
show the letter "A". This means that the (Heat up) function is active.
Set the desired cooking level (between 1 and 8); the cooking zone display will now show the letter "A" and
the desired cooking level (e.g. 6) alternately.
- If no cooking level variation is made, the indicator (D2) switches off.
Note: it is possible ONLY to increase the previously-set cooking level:
1- Select the cooking zone (E) where the Heat up function is active.
2- Increase the desired temperature by running your finger over the SLIDER control (D1).
When the Heat up function has finished running, the hob will emit a sound signal or BEEP; the relevant cooking
zone will continue to operate and the cooking level set previously, e.g. 6.
• "Pause" function (Fig.2 - Fig.3 (B)):
This function will set to pause the device, maintaining in the memory the cooking programs previously set in
- 13 -
Advertisement
