Page 1 Windows Embedded Compact 6.0 CP60 / CP60G (CE) Version 1.01...
Page 2: Disclaimer
The information contained in this document, including all pictures, illustrations and software, is the proprietary information of CIPHERLAB CO., LTD. and its respective legal owners; it is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties, with all rights reserved.
Page 3: For United States
(ICNIRP), which is 2 W/kg averaged over ten (10) gram of tissue (for example European Union, Brazil and Australia): The highest SAR value for this model phone when tested by CIPHERLAB for use at the body is 1.35 W/kg (10g).
Page 4: For United States
The highest reported SAR values for body-worn accessory and simultaneous transmission are 0.76W/kg, and 1.27W/kg respectively for CP60G. The highest reported SAR values for body-worn operation are 1.03W/Kg for CP60. For body-worn operation, the product has been tested when positioned a minimum of 15 mm from the body without any metal parts in the vicinity of the product.
Page 5: Safety Precautions
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. The use of any batteries or charging devices, which are not originally sold or manufactured by CipherLab, will void your warranty and may cause damage to human body or the product itself.
Page 6: Declaration Of Conformity
DECLARATION OF CONFORMITY...
Page 8: Release Notes
RELEASE NOTES Version Date Notes Replace Declaration of Conformity 1.01 Aug 22, 2014 Replace screenshots to match latest OS version Modify notes for swapping main battery in 1.2.1 Power Menu, 1.4.1 Main Battery Setup, and 1.4.2 Charge Batteries - Replace Main Battery Pack Revise 2D scan mode options to Laser, Presentation Mode Auto...
Page 9: Table Of Contents
CONTENTS PREFACE ....................- 2 - Copyright.................... - 2 - Disclaimer................... - 2 - Trademark Recognition ................- 2 - Contact ....................- 2 - For United States .................. - 3 - Safety Notices..................- 3 - Radio wave exposure and Specific Absor ption Rate (SAR) information....- 3 - For United States................
Page 10 1.7. Memory ................42 1.7.1. Data Loss Caution ..............42 1.7.2. Check Storage ..............42 1.7.3. Insert SD Card ..............45 1.8. Direct Data Communication ............46 1.8.1. Use Cable................46 1.8.2. Use Cradle................47 1.8.3. Syncing Tools ............... 48 1.8.4.
Page 11 5.1.2. Turn On Cellular Data ............103 5.1.3. GPRS Manager ..............106 5.2. Use Wi-Fi ................112 5.2.1. Power On Wi-Fi ..............112 5.2.2. Launch SCU ................114 5.2.3. Status Tabbed Page...............115 5.2.4. Configuration Tabbed Page............116 5.2.5. Diagnostics Tabbed Page ............131 5.3. Use Bluetooth..............138 5.3.1. Bluetooth Profiles Supported ...........138 5.3.2.
Page 12 Physical Characteristics ................205 Environmental Characteristics..............206 Programming Support ................206 Accessories ..................207 SCAN ENGINE SETTINGS ................209 Symbologies Supported ................210 LASER (SE955 & SE965HP)................213 Symbology Settings .................213 Miscellaneous ..................218 AIM Code ID – Code Characters..............218 AIM Code ID – Modifier Characters............219 2D IMAGER (SE4500DL)................
Page 13: Introduction
INTRODUCTION Thank you for choosing CipherLab products. CipherLab welcomes another Windows Embedded by introducing CP60 Series Mobile Computer. Powered by Windows Embedded Compact 6.0, the mobile computer delivers better user experience and advances enterprise mobile computing. The mobile computer has transflective LCD to hold up the readability in a wide range of light conditions, courtesy of the supplementary backlight enabled by a built-in ambient light sensor.
Page 14: Features
CP60 Mobile Computer (CE) Reference Manual FEATURES Rugged yet smoothened outlined, with hand strap for secure hold IP65/67-rated tough form to survive drop, shock, heat, cold, and impervious to moisture/dust Windows CE 6.0 OS, TI DM3730 1GHz CPU 512MB SDRAM to run application programs 4GB NAND flash to store OS, applications, settings and so on Storage expansion: Up to 32GB MicroSDHC Sunlight-readable screen to enhance the viewability of outdoor use...
Page 15: Use Mobile Computer
Chapter 1 USE MOBILE COMPUTER Before the mobile computer takes part in your work, get to know it first. This chapter includes the basic features of the mobile computer including the power supply, memory, and the units that bridge users with the mobile computer. This chapter helps you set the mobile computer to work at the earliest.
Page 16: Take A Tour
CP60 Mobile Computer (CE) Reference Manual 1.1. TAKE A TOUR This section shows the major components on the mobile computer and inside battery chamber. You will also learn how to power on/off the mobile computer and how the mobile computer gives information about its status. 1.1.1.
Page 17: Inside Battery Chamber
Chapter 1 Use Mobile Computer 1.1.2. INSIDE BATTERY CHAMBER Inside the battery chamber of the mobile computer are the sockets for SIM card and storage card. Each is equipped with a hinged cover. Battery chamber SIM card slot SD card slot Figure 2: Inside Battery Chamber 1.1.3.
Page 18: Power On
CP60 Mobile Computer (CE) Reference Manual 1.2. POWER ON To power on the mobile computer, press the Power button sitting at the upper right of the keypad. The mobile computer powers on. 1.2.1. POWER MENU The CP60 mobile computer features a power menu. This menu allows you to select whether you would like to power off the mobile computer, enter suspension, or enter sleeping mode for main battery replacement.
Page 19 Chapter 1 Use Mobile Computer Select this option if you would like to power off the mobile computer. This will close all applications and tasks currently running. All Power Off unsaved data will be lost. To power on the mobile computer, press the power button. Selecting this option will close the menu and return to the previously Cancel active screen.
Page 20: Notifications
CP60 Mobile Computer (CE) Reference Manual 1.3. NOTIFICATIONS The mobile computer features visible, audible, and tactile feedback to draw users’ prompt awareness of the mobile computer’s contiguous events such as barcode reading, wireless/mobile data connections, and battery charging. STATUS LED Three LED lights are located on the upper-right corner of the mobile computer.
Page 21: Battery
Chapter 1 Use Mobile Computer 1.4. BATTERY The mobile computer is fed by two batteries, main battery pack and backup battery. The main battery is removable and replaceable from the battery chamber while the backup battery is mounted on the main board inside the mobile computer. When the mobile computer is shipped, the main battery is stored in a package separated from the mobile computer, which keeps it in good condition for future use.
Page 22: Main Battery Setup
CP60 Mobile Computer (CE) Reference Manual 1.4.1. MAIN BATTERY SETUP To secure main battery in place, the battery door is equipped with two latches, one on each side. After pressing the battery door in, turn the door latches inwards to lock the battery door in place.
Page 23 Chapter 1 Use Mobile Computer To install the main battery pack, follow through the steps below by referencing to the illustrations: Figure 4: Main Battery Setup...
Page 24 CP60 Mobile Computer (CE) Reference Manual 1) Loosen the handstrap and pull it downwards so the metal hook is positioned at the lower edge of the Velcro band 2) Unhook the hand strap by pressing the square metal ring lightly in the middle and lifting it upwards in a single motion.
Page 25: Charge Batteries
Chapter 1 Use Mobile Computer 1.4.2. CHARGE BATTERIES Due to shipment, it is likely that the main battery and backup battery won’t be fully charged when you receive the package. Before setting the mobile computer to work, charge the main battery to full by direct charging via a power adapter (with the help of a Snap-on Charging &...
Page 26 CP60 Mobile Computer (CE) Reference Manual DIRECT CHARGING USING SNAP-ON CABLE Direct charging of the mobile computer relies on the Snap-on Charging & Communication Cable (hereinafter “snap-on cable”). There is a power jack on the connector of this cable to connect external power.
Page 27 Chapter 1 Use Mobile Computer DIRECT CHARGING USING CRADLE Direct cradle charging makes use of a Charging & Communication Cradle (hereinafter “cradle”). The cradle is one of the accessories you can opt for. Prior to charging, install main battery as described in Main Battery Setup.
Page 28: Monitor Battery Level
CP60 Mobile Computer (CE) Reference Manual 1.4.3. MONITOR BATTERY LEVEL The main battery is the only source that feeds the mobile computer to work. It also supplies the backup battery on main board to retain the data stored in DRAM. Hence when main battery level gets low, recharge it or change it as soon as possible.
Page 29 Chapter 1 Use Mobile Computer BATTERY STATUS ICONS The OS features a couple of icons that deliver main battery status. These icons can be found on the taskbar, which is settled at the bottom of every screen. Battery charging icon Battery level is illustrated by the following icons : Icon Battery Status...
Page 30 CP60 Mobile Computer (CE) Reference Manual LOW BATTERY ALERT When main battery level drops below 40%, the mobile computer prompts “Main Battery Low” for a recharge. When further reduced to under 20%, the mobile computer prompts “Main Battery Very low” to solicit your immediate action. Low battery may incur shutdown to the mobile computer and cause DRAM data damage.
Page 31 Chapter 1 Use Mobile Computer BACKUP BATTERY LEVEL 1) To check backup battery level, tap Start | Settings | Control Panel | Power On Battery tabbed page of Power Properties window, backup battery level is summarized as “Good”, “Low” or “Very Low” under the Power label. Backup battery level descriptions are as follows: Description Battery Status...
Page 32: Power Management
CP60 Mobile Computer (CE) Reference Manual 1.4.4. POWER MANAGEMENT Power issues are critical for portable devices. Always turn off the features you don’t need on the mobile computer in order to save power. To extend battery life as long as possible, always take the following actions: Suspend the mobile computer when it isn’t actively in use.
Page 33: Keypad
Chapter 1 Use Mobile Computer 1.5. KEYPAD The mobile computer has a physical keypad and a touchscreen to receive user’s input. Among the two, the touchscreen provides more intuitiveness in interacting with the device. This section shows how to input text using physical keypad and on-screen keyboard. To know how to operate the mobile computer using the touchscreen, see Touch Control.
Page 34 (Requires Function Key pressed beforehand.) Send Key available for function assignment in CipherLab utility Button Assignment. Key available for function assignment in CipherLab utility Button Assignment. Opens the previous screen worked on. Closes a menu of an application, or an opened dialog.
Page 35 Chapter 1 Use Mobile Computer Function mode is triggered. Mode Description Function is delivered to the next pressed key. Function is delivered to all pressed keys. The Fn key is also effective by pressing and holding it and then pressing the desired key.
Page 36 CP60 Mobile Computer (CE) Reference Manual NUMERIC KEYPAD Numeric keypad wedges a set of character keys at the lower half. They are laid out similar to a telephone keypad, and additionally featured are an key, Tab key , Enter key , Backspace key , and Shift key that enable more sophisticated text input.
Page 37 Chapter 1 Use Mobile Computer KEYPAD MODES With combined use of the [Alpha] key key and Shift key , enables eight input modes for keys Taskbar 0-9 on the physical keypad. The icons signify the current input state. Numeric keypad input modes: Mode Description (Keys 0-9) Trigger and Withdrawal...
Page 38 CP60 Mobile Computer (CE) Reference Manual letters and capitalizes the first one. Input mode returns to default by pressing again. Jumps to mode after a single key is pressed. Press both twice to enter this mode. Keypad enters all typed keys as capitalized alphabetic letters.
Page 39 Chapter 1 Use Mobile Computer QWERTY KEYPAD QWERTY keypad also arranges its character keys in the lower half and features them in a compact “QWERTY” layout as its name suggests. QWERTY keypad is a pared down version of an average laptop’s keyboard that bears also an key, Tab key , Enter key , Backspace key...
Page 40 CP60 Mobile Computer (CE) Reference Manual KEYPAD MODES With combined use of the key, Shift key enables four input modes for the physical keypad. The icons Taskbar signify current input state. QWERTY keypad input modes: Mode Description Trigger and Withdrawal Default mode.
Page 41 Chapter 1 Use Mobile Computer TEXT INPUT To enter text using QWERTY keypad: Literal Input The QWERTY keypad enters lowercase letters a-z by default when neither nor Shift key is pressed. To enter a letter in uppercase, press Shift key appears on the Taskbar.
Page 42: On-Screen Keyboard
CP60 Mobile Computer (CE) Reference Manual 1.5.2. ON-SCREEN KEYBOARD The OS provides users with an on-screen keyboard. Compared to a physical keypad, the on-screen keyboard bears likeness to a laptop keyboard as it has modifiers keys arranged on the left edge and features a “QWERTY” layout. The on-screen keyboard supports entering a series of diacritics for European languages by tapping a modifier key.
Page 43 Chapter 1 Use Mobile Computer MODIFIER KEYS Although the touchscreen is a resistive single-touch type, use of modifier keys, which normally involves hitting two keys, are still available on on-screen keyboard. On on-screen keyboard there are five modifier keys, which are seated at the left edge. These keys work as follows: 1) Press a modifier key on on-screen keyboard.
Page 44 CP60 Mobile Computer (CE) Reference Manual Modifier keys are explicated as follows: Description Ctrl key Once tapped, it becomes color-inverted and causes a special action from OS or the active application when a character key is tapped. It quits once the said action is triggered or when it is tapped again.
Page 45 Chapter 1 Use Mobile Computer Letter variant “ü” is entered After the letter variant “ü” is entered, the on-screen keyboard restores to normal English alphanumeric layout. Diacritical letters and letter variants are presented bother lowercase and uppercase. Lowercase Uppercase...
Page 46 CP60 Mobile Computer (CE) Reference Manual OTHER KEYS Description Tab key Navigates among the highlight items in some applications. For text input, it inserts Tab character, which means it moves caret to the next tab stop. Backspace Erases the characters to the left of caret. Enter key Executes a command or confirms input.
Page 47: Change On-Screen Input Method
Chapter 1 Use Mobile Computer 1.5.3. CHANGE ON-SCREEN INPUT METHOD Aside from the on-screen keyboard, the CP60 mobile computer features another on-screen input method called Transcriber, which is a handwriting recognition software that can be used within any application. It supports text input on any part of the screen, and also recognizes entire words instead of individually written letters.
Page 48: Edit Text
CP60 Mobile Computer (CE) Reference Manual 1.5.4. EDIT TEXT On the mobile computer, you may cut, copy, and paste text within an application or across applications by the menu commands. Some applications don’t support editing some or all of the text they display while others may offer their own way to edit text. EDIT TEXT IN INPUT FIELDS To edit text in a text input field: 1) Tap where you want to edit text.
Page 49: Touch Control
Chapter 1 Use Mobile Computer 1.6. TOUCH CONTROL The mobile computer’s LCD is overlaid by a resistive touch panel and thus forms a resistive touchscreen. Since a resistive touchscreen locates the user’s touch by the force applied on it, by operating with the stylus one can apply minimum force to trigger actions from the touchscreen.
Page 50 CP60 Mobile Computer (CE) Reference Manual Screen Rotation window opens with three orientation modes to select from and an option to suspend the mobile computer when the screen is facing down. Three screen orientation modes Allows mobile computer to enter suspension when facing down 2) Tap the modes that you wish to enable.
Page 51: Adjust Backlight
Chapter 1 Use Mobile Computer SIGNATURE MODE The signature mode is for combined usage with the CipherLab application Signature. With this mode enabled, the screen will immediately rotate 180° when the front of the mobile computer is tilted outwards, which is convenient for signing by a second party.
Page 52 CP60 Mobile Computer (CE) Reference Manual AUTOMATIC BACKLIGHT PROFILES The mobile computer stores three backlight profiles to represent backlight level under different environments. These can be configured according to user’s likings. To set backlight profiles: 1) Tap Start | Settings | Control Panel | Backlight Setting Brightness tabbed page opens.
Page 53: Calibration
Chapter 1 Use Mobile Computer 1.6.4. CALIBRATION A resistive touchscreen needs calibration to work accurately after serving for a period of time. Calibration aligns the coordinates of the touch panel and the LCD underneath to improve touch accuracy. To calibrate the touchscreen: 1) Tap Start | Settings | Control Panel | Stylus 2) Tap Calilbration tabbed page.
Page 54: Memory
CP60 Mobile Computer (CE) Reference Manual 1.7. MEMORY The mobile computer packs the following internal memory units to retain data and instructions from users: Internal Storage: Random-access Memory (RAM) and Flash Memory 512MB SDRAM for temporary storage and fast access of active applications. When the main battery pack is absent, SDRAM is fed by backup battery to retain data.
Page 55 Chapter 1 Use Mobile Computer To check RAM usage on the mobile computer: 1) Tap Start | Settings | Control Panel | System 2) Tap Memory tabbed page. This page delivers capacity and usage of the SDRAM onboard. Memory is divided into Storage memory and Program memory.
Page 56 CP60 Mobile Computer (CE) Reference Manual EXTERNAL STORAGE For external storage, tap Start | Settings | Control Panel | Storage Information The available space on the storage card is shown under the Storage Card label. (If no storage card is installed on the mobile computer, the available space will be shown as 0.)
Page 57: Insert Sd Card
CP60 Mobile Computer (CE) Reference Manual 1.7.3. INSERT SD CARD Day-to-day use of the mobile computer might cause the available internal storage to run short. Equip the mobile computer with an external memory unit to expand storage capacity. Follow the steps below to install a SD card: 1) Power off the mobile computer.
Page 58: Direct Data Communication
CP60 Mobile Computer (CE) Reference Manual 1.8. DIRECT DATA COMMUNICATION “Direct” data connection means “hardwired” data connection between the mobile computer and a Windows-based PC as opposed to wireless connection. Direct data connection relies on a RS-232 cable or a USB cable (sometimes plus an auxiliary cradle) between the two mentioned devices.
Page 59: Use Cradle
Chapter 1 Use Mobile Computer 1.8.2. USE CRADLE Direct data communication using a cradle: 1) Seat the mobile computer in a Charging and Communication Cradle (hereinafter “cradle”). 2) Connect the cradle to your PC with a USB cable. Fix the cable to both sides. ActiveSync will automatically detect connection between the two and prompt for data synchronization.
Page 60: Syncing Tools
CP60 Mobile Computer (CE) Reference Manual 1.8.3. SYNCING TOOLS Microsoft’s syncing tools enables users to update or back up the data on their mobile computers to desktop computers. Two syncing tools are featured by Microsoft - ActiveSync and Windows Mobile Device Center (“WMDC”).
Page 61: St Usb Sync
Chapter 1 Use Mobile Computer 1.8.5. 1 USB SYNC This section will guide you through USB syncing. For Bluetooth syncing, see Bluetooth ActiveSync. To connect ActiveSync using USB: 1) Download the right syncing tool as described in Syncing Tools and install it on your PC. 2) Connect the mobile computer and your PC as described in Use Cable Cradle.
Page 62: Disconnect Usb Activesync
CP60 Mobile Computer (CE) Reference Manual If you have pressed Cancel, Microsoft ActiveSync opens showing “Guest” and “Connected”. The mobile computer and the PC are connected but the data is not synchronized. A “Temporary Relationship” is established between the mobile computer and the PC Note: If you encounter trouble during USB ActiveSync connection, tap Start | Settings | PC Connection and make sure “Enable direct connections to the desktop computer”...
Page 63: Activesync Actions To Take
Chapter 1 Use Mobile Computer 1.8.7. ACTIVESYNC ACTIONS TO TAKE Once “Synchronization Relationship” or “Temporary Relationship” is established between two computers, a variety of actions can be taken to enhance resource sharing between them as previously mentioned in Sync Partnership. In summary, “Synchronization Relationship”...
Page 64 CP60 Mobile Computer (CE) Reference Manual 4) Select the application program(s) to install to the mobile computer, and deselect the application program(s) to uninstall from the mobile computer. 5) Press the OK button. ActiveSync proceeds to install programs and/or remove programs to/from the mobile computer.
Page 65 Chapter 1 Use Mobile Computer The mobile computer’s internal storage root directory “Mobile Device” opens presenting a few folders (and files). 4) Add File Shortcuts to Desktop Double-click My Windows Mobile-Based Device 5) Double-click Program Files. Program Files folder opens. This is where the downloaded applications are normally installed on the mobile computer’s local storage.
Page 66 CP60 Mobile Computer (CE) Reference Manual ADD ITEM SHORTCUTS TO DESKTOP To add a shortcut of an application or file to the mobile computer’s desktop: 1) Connect two computers as described in Use Cable Cradle. 2) Sync two computers as described in 1st USB Sync 3) On the PC, from ActiveSync menu bar, select Tools | Explore Pocket PC, or from its toolbar, press Explore...
Page 67 Chapter 1 Use Mobile Computer BACKUP DATA To best protect your work, back up the data on your mobile computer regularly. You may choose to manually back up using ActiveSync to copy & paste the files to your PC. USB PASS-THROUGH NETWORKING ActiveSync supports “Pass-Through Networking”...
Page 68: Volume And Audio
CP60 Mobile Computer (CE) Reference Manual 1.9. VOLUME AND AUDIO 1.9.1. AUDIO PLAYBACK Use a Bluetooth headset for audio playback and hands-free telephone communication. See Bluetooth. Note: Bluetooth headsets that communicate via A2DP are not supported. 1.9.2. VOLUME CONTROL The mobile computer has two volume control facilities – the physical volume rocker perched on the left side of the mobile computer and the on-screen volume gauge featured by the OS.
Page 69 Chapter 1 Use Mobile Computer 2) Adjust the settings to meet your needs. When finished, tap OK on the taskbar to apply the settings. Note: When using the physical volume rocker to adjust system volume, make sure Volume & Sounds window is not the active window on-screen.
Page 70 CP60 Mobile Computer (CE) Reference Manual...
Page 71: Data Capture
Chapter 2 DATA CAPTURE Although highly converged, the mobile computer is also a dedicated barcode reader. The mobile computer is shipped with either a (laser) 1D reader or 2D imager. A number of symbologies are supported and data about them can be decoded and collected. After data has been collected, the mobile computer can output it locally to applications installed on the mobile computer or to the host computer so data storage, advanced data analysis and more special services can be performed.
Page 72: Configure Reader
The mobile computer is capable of reading printed barcodes. The reader module can be a either a (laser) 1D reader or a 2D imager. The mobile computer is installed with a CipherLab utility Reader Config to configure the scan engine built inside. Use it to create a profile of settings that best suits your needs.
Page 73: General Settings
Chapter 2 Data Capture 2.1.2. GENERAL SETTINGS General Settings is where all reader settings are accessed from except for symbologies settings. Tap the green arrow next to each item to enter the sub-menu for that given item. Tap to enter each General Settings sub-menu The functions under General Settings include:...
Page 74 CP60 Mobile Computer (CE) Reference Manual SCANNER PREFERENCES Scanner Preferences page can be entered by tapping the given item on the Reader Config main settings page. The options provided in this page differ according to the type of scan engine (either 1D or 2D) built within the mobile computer. To open Scanner Preferences page: 1) Open Reader Config as described in Launch Reader...
Page 75 Chapter 2 Data Capture 1D (LASER) READER SETTINGS Setting Description Default Decode Timeout Sets the maximum time for the decoding process during a 3 sec scan. Configurable between 1 sec to 9 sec. Redundancy Level Sets how many successful readings should be done before Level 1 linear barcodes such as Codabar, MSI, and Interleaved 2 of 5 can be decoded.
Page 76 CP60 Mobile Computer (CE) Reference Manual 2D IMAGER SETTINGS Setting Description Default Decode Timeout Sets the maximum time for the decoding process during a 3 sec. scan. Configurable between 1 sec to 9 sec. Redundancy Level Sets how many successful readings should be done before Level 1 linear barcodes such as Codabar, MSI, and Interleaved 2 of 5 can be decoded.
Page 77 Chapter 2 Data Capture DATA OUTPUT Data Output allows users to set the way to output decoded data. To open Data Output settings page: 1) Open Reader Config as described in Launch Reader Config. Reader Config main menu opens. 2) Tap the arrow next to Data Output. Data Output settings page opens.
Page 78 CP60 Mobile Computer (CE) Reference Manual HOW TO OUTPUT After the output destination is set, configure how to output decoded data, i.e. the “format” to present decoded data. Setting Description Default Auto Enter Adds an ENTER character before or after each scanning act. Decoded This function saves the trouble pressing [Enter] key to data +...
Page 79 Chapter 2 Data Capture NOTIFICATION SETTINGS Notification Settings enables audible, visible and tactile feedback for scanning good read, which helps notify the user of a successful decoding. To open Notification Settings page: 1) Open Reader Config as described in Launch Reader Config.
Page 80: Symbology
CP60 Mobile Computer (CE) Reference Manual 2.1.3. SYMBOLOGY Symbology section sets the symbologies to read, and also enables/disables some feature(s) for a symbology to read, such as: Customize and transmit start/stop characters Verify/transmit check digits Enable/disable addon digits Convert to another symbology Transmit symbology ID Symbology To open Symbology settings page:...
Page 81 Chapter 2 Data Capture Symbology settings page opens listing all symbologies which can be decoded. 1D Symbologies 2D Symbologies SYMBOLOGY SETTINGS Tap the arrow next to each symbology checkbox to access detailed settings for that symbology.
Page 82 CP60 Mobile Computer (CE) Reference Manual GENERAL PREFERENCES For certain symbologies, common settings are grouped together and displayed in a detailed settings page for that barcode family. To open the general settings page for a set of symbologies, tap the arrow next to General Preference. General settings are provided for Composite Code, Postal Code, and UPC/EAN families.
Page 83: Miscellaneous
Chapter 2 Data Capture 2.1.4. MISCELLANEOUS This section allows enabling code ID transmission for easy identification of the scanned barcode, and enabling picklist mode to enhance decoding accuracy. Miscellaneous Setting Description Default Transmit AIM Code ID Sets whether to include AIM code ID character in the Deselected decoded data.
Page 84: Reader Config Option Menu
CP60 Mobile Computer (CE) Reference Manual 2.1.5. READER CONFIG OPTION MENU Reader Config provides an option menu which is accessible on the menu bar of the main settings page. This menu allows you to import/export all settings in a re-usable format, reset all settings back to factory default, view copyright and version information, and exit the application.
Page 85 Chapter 2 Data Capture RESET TO FACTORY DEFAULTS This function restores all settings in the Reader Config application to default. To enable Factory Reset: 1) Open Reader Config as described in Launch Reader Config. Reader Config main menu opens. 2) Tap Menu button on the menu bar to open the option menu. 3) Tap Reset to Factory defaults.
Page 86 CP60 Mobile Computer (CE) Reference Manual IMPORT AND EXPORT Reader Config supports saving the settings and exporting them as an .xml file. Previously exported symbology and scanner settings can be imported again on the mobile computer. This can also be used to implement identical Reader Config settings on two or more devices.
Page 87 Chapter 2 Data Capture To export settings: 1) Open Reader Config as described in Launch Reader Config. Reader Config main menu opens. 2) Tap Menu button on the menu bar to open the option menu. 3) Tap Export. An export page opens allowing you to enter and select information about the profile to be saved.
Page 88 CP60 Mobile Computer (CE) Reference Manual ABOUT Tap About in the Reader Config option menu to display software version and copyright information. Information about the software...
Page 89: Read Printed Barcodes
Chapter 2 Data Capture 2.2. READ PRINTED BARCODES Aside from output to destinations as per Keyboard Emulation settings, Reader Config provides a Scan Test feature for quick viewing of decoded data. To perform test scanning of barcodes: 1) Open Reader Config as described in Launch Reader Config.
Page 90 CP60 Mobile Computer (CE) Reference Manual The decoded data will appear on the page. When finished viewing, tap on the title bar to leave the test scan page. Tap to exit the test scan page To display more information such as barcode type and length, configure the reader as in Data Output.
Page 91: Camera
Chapter 3 CAMERA The mobile computer is equipped with a 5.0 mega-pixel camera. The OS also has an integrated camera application for taking pictures and storing them on the mobile computer’s storage where they can be viewed, edited and output. The camera application provides users with customization that allows better image documentation.
Page 92: Launch Camera
CP60 Mobile Computer (CE) Reference Manual 3.1. LAUNCH CAMERA To launch the camera: 1) Tap Start | Programs | Camera Capture Camera application opens and is ready to take pictures. 3.1.1. CAMERA SCREEN Camera opens showing a subject area on the screen, and a toolbar at the top. Exits camera Toolbar application...
Page 93: Camera Toolbar
Chapter 3 Camera 3.1.2. CAMERA TOOLBAR The camera toolbar allows users to take and save pictures, view saved images, adjust camera settings, enable camera flash light and view information of the application. Button Description Views pictures saved on the mobile computer’s internal storage. Supported file formats include .bmp and .jpg files.
Page 94: Take Pictures
CP60 Mobile Computer (CE) Reference Manual 3.2. TAKE PICTURES To take a picture: 1) Open camera as described in Launch Camera. 2) Enable/disable camera flash and adjust picture quality or other settings according to your preferences. See Camera Settings. 3) Frame your object on the screen. 4) Press the Enter button on the keypad to take the picture.
Page 95: Camera Settings
Chapter 3 Camera 3.2.1. CAMERA SETTINGS The camera supports changing resolution, flash light mode, camera effect, brightness, and default file storage format and location. To access camera settings: 1) Open camera as described in Launch Camera. 2) Tap the button in the toolbar. A dialog appears on-screen showing various option settings.
Page 96: View Pictures
CP60 Mobile Computer (CE) Reference Manual 3.3. VIEW PICTURES To view a taken picture or an image stored on the mobile computer: 1) Tap the button on the toolbar. 2) Browse to the desired path and select the file to view. The picture will be displayed in the preview screen below.
Page 97: Operating System
Chapter 4 OPERATING SYSTEM The mobile computer is powered by Windows Embedded Compact 6.0, a member of Windows Embedded family. Windows Embedded Compact 6.0 bears much similarity to desktop OS, and users rely only on a few basic gestures such as tap, double-tap and drag to navigate within the OS.
Page 98: Desktop
Chapter 4 Operating System 4.1. DESKTOP Desktop is where all features on the mobile computer are accessed from. Basic operations on the desktop: Tap the Start button to open the Start menu. Double-tap an application icon to open it. Customize the desktop by changing the background and the items to display. See Customize Desktop and Start Menu for more details.
Page 99: Taskbar
Chapter 4 Operating System 4.1.1. TASKBAR At the bottom of the screen is the taskbar, which is divided into the following sections: Start button: opens Start menu Task button section that shows a minimized window button of the current application or task open on-screen Notification area which displays icons for connection status of the mobile computer, as well as system time...
Page 100: Start Menu
CP60 Mobile Computer (CE) Reference Manual Ethernet A specific wireless connection has been established successfully. Double-tap the icon to open a dialog to check IP information. Included connections are: Bluetooth PAN 802.11a/b/g/n WWAN connection Ethernet Indicates the Wi-Fi module is enabled. The more the green bars, the stronger the signal.
Page 101: Customize Desktop And Start Menu
Chapter 4 Operating System 4.1.3. CUSTOMIZE DESKTOP AND START MENU Customize the desktop by changing the background, application shortcuts, and so on. Rearrange the application shortcuts to make the applications that you use most often easy to access. CHANGE BACKGROUND You may change the background of the desktop to a picture of your own choice.
Page 102 CP60 Mobile Computer (CE) Reference Manual The selected file will appear on the desktop as the background image. CHANGE APPEARANCE You may change the overall scheme, color of title bars, dialog boxes, menu text, selected items and so on to suit your preferences. 1) Tap and hold any blank space on the desktop.
Page 103 Chapter 4 Operating System ADD ITEMS TO DESKTOP ADD APPLICATION SHORTCUTS 1) On the mobile computer, tap My Device on the desktop. 2) Browse to the executable file of the program you would like to create a shortcut for. 3) Tap and hold the file. A pop-up menu will show on the screen. 4) Tap Copy in the pop-up menu.
Page 104 CP60 Mobile Computer (CE) Reference Manual REMOVE ITEMS FROM START MENU 1) On the mobile computer, tap My Device on the desktop. 2) Browse to My Device\Windows\Programs. Programs folder opens. All applications available in the Start menu can be found here. 3) Tap and hold the application to remove.
Page 105: Managing Programs
2) Tap the desired program to launch it on-screen. The programs pre-installed on the mobile computer include: Icon Description CIPHERLAB UTILITIES (Reserved folder.) APPLOCK AppLock limits access to programs and settings on the mobile computer through an authorization mechanism. See the AppLock User Guide for details.
Page 106: Switch Between Active Tasks
CP60 Mobile Computer (CE) Reference Manual MEDIA PLAYER Audio/video file player. MICROSOFT WORDPAD Wordpad for entering text. REMOTE DESKTOP CONNECTION Program for connection to a remote computer. SIGNATURE Signature application which is available for C++ programming via API deployment. See the CP60 C++ Programming Guide for details.
Page 107: Install Applications
Chapter 4 Operating System 4.2.4. INSTALL APPLICATIONS As mentioned in Add/Remove Programs, you can download and install an application on your PC first and offload it to the mobile computer later using Microsoft ActiveSync. Alternatively, the OS allows you to install an application right from the mobile computer. Follow the steps below to complete installation: 1) Using your PC, copy the installation file (.CAB) to the mobile computer’s internal storage via ActiveSync.
Page 108 CP60 Mobile Computer (CE) Reference Manual 4) When installation is finished, launch it by tapping Start | Programs and locating it in the Programs menu. Alternatively, you may download an application to install from the Internet. See Use Wi-Fi USB Pass-through Networking for how to connect the mobile computer to the Internet.
Page 109 Chapter 4 Operating System UNINSTALL APPLICATIONS On the mobile computer, the acquired (non-inherent) applications can be depleted from the OS through manual removal (uninstallation). To uninstall an application: 1) Tap Start | Settings | Control Panel | Remove Programs Remove Programs page opens showing the applications downloaded and installed from external sources.
Page 110: Suspend & Reset Mobile Computer
CP60 Mobile Computer (CE) Reference Manual 4.3. SUSPEND & RESET MOBILE COMPUTER To save from repeatedly charging and replacing batteries, suspend the mobile computer when you are not actively using it. Suspending (or “turning off”) the mobile computer holds the device from running without cutting off power. It is a “soft-off” state which enables less power consumption, and also a state which the device can quickly awake from since there is no need to restart the OS and applications.
Page 111: Wake Up Mobile Computer
Chapter 4 Operating System 4.3.2. WAKE UP MOBILE COMPUTER “Waking up” refers to restoring the suspended device to its previous working state. The mobile computer can be awoken both manually and automatically. MANUAL AWAKENING Press (without holding) the power button or central scan key to wake up the mobile computer.
Page 112 CP60 Mobile Computer (CE) Reference Manual WARM BOOT (SOFT RESET) “Warm boot” is also known as “soft reset”. When the mobile computer runs slower than normal or when one or more active applications crash, perform warm boot to close all active applications and restart the mobile computer without turning off power supply to hardware.
Page 113: Radios
Chapter 5 RADIOS The mobile computer is a versatile networker. It integrates Wi-Fi and Bluetooth for wireless data, and optionally an HSPA+ (3.8G) module for mobile data. It also includes a GPS receiver which can detect your locations on earth with street-level accuracy. With the help of these radios, the mobile computer keeps users online all the time.
Page 114: Access Cellular Wan
CP60 Mobile Computer (CE) Reference Manual 5.1. ACCESS CELLULAR WAN When you insert a SIM card in the mobile computer and power on the phone module, the mobile computer will connect to your mobile carrier’s cellular wide area networks (WAN) for data transmission.
Page 115: Turn On Cellular Data
Chapter 5 Radios 5.1.2. TURN ON CELLULAR DATA Before establishing a WWAN connection, turn on cellular data in Wireless Manager. 1) Tap Start | Settings | Control Panel | Wireless Manager 2) By default, the Cellular Data label is turned “off”. Tap the “Off”...
Page 116 CP60 Mobile Computer (CE) Reference Manual CELLULAR DATA STATUS ICONS After cellular data is enabled, an icon will appear on the taskbar to show the connection status. The icons available for cellular data connection status are as follows: Icon Indication Initializing the cellular data module Cellular data is disconnected Connecting to cellular data...
Page 117 Chapter 5 Radios CONNECT/DISCONNECT CELLULAR DATA Tap the icon to access the menu that allows you to choose to connect/disconnect cellular data. The icon on the taskbar will reflect the current status (disconnected, connecting, or connected). Disconnect a current WWAN connection Connect to a WWAN network...
Page 118: Gprs Manager
CP60 Mobile Computer (CE) Reference Manual 5.1.3. GPRS MANAGER GPRS Manager allows you to configure WWAN settings, change the PIN code of your SIM card, and select whether to retry connection after a previous attempt to connect has failed. To open GPRS Manager, tap Start | Settings | Control Panel | GPRS Manager Tap the Cellular Data icon on the Wireless Manager settings page.
Page 119 Chapter 5 Radios BASIC SETTINGS TABBED PAGE The Basic Settings tabbed page sets whether to allow reconnection to the previously connected WWAN network, and the number of times and interval for this reconnection attempt. It also features buttons for opening an Advanced settings page and resetting the values to default.
Page 120 CP60 Mobile Computer (CE) Reference Manual ADVANCED SETTINGS If you need to change the dial-up settings, tap the Advanced button and configure the following items in the GPRS Properties dialog box. Tap OK to save the settings. Setting Description AP Name Specify the AP name for the mobile computer to connect to.
Page 121 Chapter 5 Radios SECURITY TABBED PAGE The Security tabbed page is only available when a SIM card is installed and cellular data has been enabled. Use this tabbed page to enable PIN code verification for the SIM card, or change the PIN code if necessary. Note: After changing PIN code settings, restart power for cellular data for the changes to take effect.
Page 122 CP60 Mobile Computer (CE) Reference Manual When disabling the Enable PIN checkbox, a dialog box will appear asking you to enter the PIN code first as confirmation to make adjustments. CHANGE PIN CODE When a PIN code is enabled and you would like to change it, tap Change PIN to open the dialog box.
Page 123 Chapter 5 Radios ABOUT TABBED PAGE To check information about the software, tap the About tabbed page.
Page 124: Use Wi-Fi
CP60 Mobile Computer (CE) Reference Manual 5.2. USE WI-FI The mobile computer is capable of Wi-Fi, a wireless networking technology making use of an access point, also known as “hotspot”, to connect to a wireless local area network. To use Wi-Fi, the mobile computer has to connect to a hotspot. Some hotspots are open for connection while others request a key to authenticate access.
Page 125 Chapter 5 Radios Note: Wi-Fi power settings under Wireless Manager will be kept through suspension and warm boot/cold boot. After the mobile computer resumes from suspension or restarts, Wi-Fi power status will be maintained and the mobile computer will attempt to reconnect the previous connection.
Page 126: Launch Scu
CP60 Mobile Computer (CE) Reference Manual 5.2.2. LAUNCH SCU Wi-Fi settings can be adjusted with Summit Client Utility. Within this application are three tabbed pages which allow users to select the access point for connection, create profiles for better management, perform diagnostics on connectivity, and fine-tune property settings to meet their individual requirements.
Page 127: Status Tabbed Page
Chapter 5 Radios 5.2.3. STATUS TABBED PAGE The Status tabbed page provides basic information on WLAN connection and Bluetooth status. Wi-Fi settings can be configured on Configuration Tabbed Page. Wi-Fi status Bluetooth status (service coming soon) Note: SCU does not currently support viewing or configuring Bluetooth settings.
Page 128: Configuration Tabbed Page
CP60 Mobile Computer (CE) Reference Manual 5.2.4. CONFIGURATION TABBED PAGE TURN ON/OFF WI-FI MODULE Select the Wi-Fi checkbox to turn on Wi-Fi. Deselect it to shut down Wi-Fi. Turn on Wi-Fi module Note: SCU does not allow configuration of Bluetooth settings. To establish and manage Bluetooth connections, tap Start | Settings | Control Panel | BT Manager...
Page 129 Chapter 5 Radios ACTIVE PROFILE A profile is a set of parameters that define the manner which a device associates to a wireless LAN (WLAN) infrastructure. A profile contains information including the System Set Identifier (SSID, the "name" of the WLAN infrastructure), means of data encryption, authentication type, and security credentials.
Page 130 CP60 Mobile Computer (CE) Reference Manual CREATE WI-FI PROFILE To create a Wi-Fi Profile: 1) Open SCU as described in Launch SCU. 2) Tap the Configuration tab to show the Configuration tabbed page. 3) Tap Scan to view a list of access points that are broadcasting their SSIDs. You may sort the list by tapping the column headers.
Page 131 Chapter 5 Radios 5) A profile settings page opens showing detailed radio settings. Tap each item and adjust its Value to suit your needs. 6) When finished fine-tuning all settings, tap Commit to save the profile. 7) Tap OK on the title bar to close the Profile Settings page and return to Configuration settings.
Page 132 CP60 Mobile Computer (CE) Reference Manual MANAGE WI-FI PROFILE To manage your profiles: 1) Open SCU’s Configuration tabbed page as described in Create Wi-Fi Profile. 2) Tap Manage Profiles to open the Profile settings page. Item Description Profile When SCU is first launched, “Default” is the active profile. Unless it is modified, this profile does not specify an SSID, EAP type or encryption method.
Page 133 Chapter 5 Radios Tap New and enter a unique name for the profile. Configure the Radio settings, Encryption, EAP Type, and other settings for this new profile. The name for each profile must be unique You can define up to 20 profiles Delete Select a profile from the drop-down menu and tap Delete.
Page 134 CP60 Mobile Computer (CE) Reference Manual Radio After selecting a profile in the Profile drop-down bar, configure radio settings in the Settings scrollable menu below. Property Description Profile Name Tap to rename the selected profile. Up to 32 characters allowed. SSID Service Set Identifier (SSID) for the WLAN infrastructure to which the radio will connect.
Page 135 Chapter 5 Radios Maximum In Max Power Savings (Max PSP) mode, the access point buffers incoming messages for the radio, which wakes up periodically and connects to the access point to see if any buffered messages are waiting. The radio requests buffered messages and then goes back to sleep.
Page 136 CP60 Mobile Computer (CE) Reference Manual Ad Hoc When selected, Summit radio associates to another station radio that is in ad hoc mode and has the same SSID and, if configured, static WEP key. Default: ABG rates full Auth Type 802.11 authentication type used when associating to an AP.
Page 137 Chapter 5 Radios Password (up to 32 characters) PAC Filename (up to 32 characters): You may create a protected access credential (PAC) for each client device. When creating a PAC manually, you must store it in the directory identified in Certs Path on the Globals settings page.
Page 138 CP60 Mobile Computer (CE) Reference Manual Commit After making any changes on the Profile tabbed page, the Commit button must be tapped in order for the settings to take effect.
Page 139 Chapter 5 Radios MANAGE GLOBAL SETTINGS Global settings include radio and security settings that apply to all profiles in SCU. To open the Global settings page: 1) Open SCU’s Configuration tabbed page as described in Create Wi-Fi Profile. 2) Tap Manage Profiles to open the Profile settings page. 3) Tap the Globals tab to open the Global settings page.
Page 140 CP60 Mobile Computer (CE) Reference Manual 1, 7, 13 For ETSI and TELEC radios only Custom Indicates the system registry has been edited to include a value other than those available in the drop-down value Default: Full DFS Channels Indicates whether to support 5 GHz (802.11a) channels where dynamic frequency selection (DFS) is required.
Page 141 Chapter 5 Radios Auth Server Type of authentication server being used for EAP authentication. Value: Type 1 Cisco Secure ACS or another server that uses PEAPv1 PEAP with EAP-MSCHAPV2 (PEAP-MSCHAP) Type 2 A different authentication server, such as Juniper Networks Steel Belted RADIUS, that uses PEAPv0 for PEAP-MSCHAP Default: Type 1 TTLS Inner Method...
Page 142 CP60 Mobile Computer (CE) Reference Manual Admin Password Auth Timeout (s) Specifies how long it will wait for an EAP authentication request to succeed or fail. If authentication credentials are specified in the active profile and the authentication times out, then association will fail. If authentication credentials are not specified in the active profile and the authentication times out, then the user will be required to enter credentials again.
Page 143: Diagnostics Tabbed Page
Chapter 5 Radios 5.2.5. DIAGNOSTICS TABBED PAGE Perform diagnostic tests to troubleshoot connection issues when necessary. To open the Diagnostics page: 1) Open SCU as described in Launch SCU. 2) Tap the Diagnostics tab to show the Diagnostics page. Diagnostics status for Wi-Fi and Bluetooth shows, along with on-screen buttons to open Advanced settings and view software version information.
Page 144 CP60 Mobile Computer (CE) Reference Manual ADVANCED DIAGNOSTICS To access Advanced diagnostics settings: 1) Open Diagnostics Tabbed Page. 2) Tap the Advanced button to open advanced diagnostics settings. CHECK STATUS To check diagnostics status, select Status in the drop-down bar. Select Status to check connection details...
Page 145 Chapter 5 Radios USE PING TOOLS To perform ping tests, select Ping Tools in the drop-down bar. Select Ping Tools to diagnose the connection Device IP address AP Name Item Description Destination Enter the address to ping. Ping Payload The amount of data to be transmitted on a ping. Value: 32, 64, 128, 256, 512, 1024 Default: 32 (bytes) Ping Delay...
Page 146 CP60 Mobile Computer (CE) Reference Manual Start Ping When an active ping is initiated, the screen displays a ping indicator that blinks in green (for a successful ping) or red (for an unsuccessful ping). The ping indicator is hidden when the screen is switched to a tab other than Diags or Status. Release/Renew Obtain a new IP address through DHCP release/renew, and log all activity in the output area at the bottom.
Page 147 Chapter 5 Radios (Re)connect Disable and enable the radio, apply or re-apply the current profile, attempt to associate and authenticate to the wireless network, and log all activity in the output area at the bottom.
Page 148 CP60 Mobile Computer (CE) Reference Manual USE DEBUG TOOLS To check debug settings, select Debug in the drop-down bar. Select Debug to check debug settings Item Description Driver Debug Select whether to debug the WLAN driver, and the output mode for driver debug. Value: Not set, 1-Text(Low), 2-Text, 3-Text(High), 4-Serial(Low), 5-Serial, 6-Serial(High) Default: Not set...
Page 149 Chapter 5 Radios SOFTWARE VERSION INFORMATION To check software version information: 1) Open Diagnostics Tabbed Page. 2) Tap the About button to view information about SCU version, device driver, and software developer.
Page 150: Use Bluetooth
CP60 Mobile Computer (CE) Reference Manual 5.3. USE BLUETOOTH The mobile computer is Bluetooth-enabled to synchronize data with other devices such as PCs, car hands-free kits, headsets, printers, PDAs, and cell phones. Class II Bluetooth devices enable wireless connections over a short distance of around 10 meters.
Page 151 Chapter 5 Radios Device ID tabbed page opens. Change device name to make the mobile computer more recognizable. 3) Enter a name of your choice. 4) Tap OK on the title bar to apply the change.
Page 152: Turn On/Off Bluetooth
CP60 Mobile Computer (CE) Reference Manual 5.3.3. TURN ON/OFF BLUETOOTH To turn on/off Bluetooth power: 1) Tap Start | Settings | Control Panel | Wireless Manager Wireless Manager opens. 2) Make sure the Bluetooth label is turned “on” If the Bluetooth label is turned “off”, tap the “Off” icon to switch on Bluetooth power.
Page 153: Set Bluetooth Visibility
Chapter 5 Radios 5.3.4. SET BLUETOOTH VISIBILITY By opening or closing Bluetooth visibility, you can control whether or not other Bluetooth devices can discover the mobile computer. To set Bluetooth visibility on the mobile computer: 1) Tap the Bluetooth icon on the taskbar and select Setting in the pop-up menu.
Page 154: Launch Bt Connect
CP60 Mobile Computer (CE) Reference Manual 5.3.5. LAUNCH BT CONNECT BT Connect is a connection tool for establishing Bluetooth partnerships. To launch BT Connect: 1) Tap the Bluetooth icon on the taskbar and select Maximized in the pop-up menu. BT Connect launches with a menu bar on top and a blank field for searching devices. See below for a description of menu bar items and their functions: Button Description...
Page 155: Search For Bluetooth Devices
Chapter 5 Radios 5.3.6. SEARCH FOR BLUETOOTH DEVICES To search for a Bluetooth device to connect to: 1) Tap Device to discover Bluetooth devices nearby. Wait for a few seconds for the mobile computer to list all the discovered devices. 2) If the device that you wish to connect to is not listed, make sure its Bluetooth status is set as discoverable.
Page 156: Pair Bluetooth Devices
CP60 Mobile Computer (CE) Reference Manual 5.3.7. PAIR BLUETOOTH DEVICES IDENTIFY BLUETOOTH DEVICE To check the identity of a Bluetooth device: 1) Open BT-Connect page as described in Launch BT Connect. 2) In the device list, tap and hold a device until a pop-up menu appears. 3) Tap MAC address in the menu to identify the selected device.
Page 157 Chapter 5 Radios PAIR If authentication is enabled on the Bluetooth device, pairing will be required to connect to that device. Pairing can be done by using a pin code to ensure secure Bluetooth connection. 1) In the device list, tap and hold the device to pair with. 2) Enter a pin code in the pop-up window that appears.
Page 158 CP60 Mobile Computer (CE) Reference Manual Once the mobile computer and the remote Bluetooth device are paired, a lock icon will be displayed next to the device. 4) Double-tap the device to find out which Bluetooth services are available. 5) Tap and hold a desired Bluetooth service to take further actions.
Page 159 Chapter 5 Radios UNPAIR To unpair a Bluetooth device: 1) In the device list, tap and hold the device to unpair. A pop-up menu will appear. 2) Select Unpair in the pop-up menu.
Page 160: Bluetooth Data Transfer
CP60 Mobile Computer (CE) Reference Manual 5.3.8. BLUETOOTH DATA TRANSFER After the mobile computer is paired to a remote Bluetooth Device, it is ready to begin Bluetooth data communication. FILE TRANSFER To exchange files via file transfer (FTP) service: 1) On the Device page, double-tap the paired Bluetooth device. 2) Tap and hold FTP Transfer and select Open in the pop-up menu.
Page 161 Chapter 5 Radios 4) Select an object to transfer to the paired Bluetooth device. On the remote Bluetooth device, the object will be stored under the directory specified on Service page | FTP Transfer | Change Local Path. 5) To store a transferred file to the specified local path on the mobile computer, tap and hold a file and select Get File in the pop-up menu.
Page 162 CP60 Mobile Computer (CE) Reference Manual OBJECT PUSH To use object push (OPP) service to send an object to a remote Bluetooth device: 1) On the Device page, double-tap the paired Bluetooth device to open a page showing its available services. 2) Tap and hold Object Push and select Push File in the pop-up menu.
Page 163 Chapter 5 Radios 3) Select an object to transfer to the paired Bluetooth device. Wait for a few moments while the file transfers to the remote Bluetooth device. 4) On the remote Bluetooth device, the object will be stored under the directory specified on Service page | Object Push | Change Local Path.
Page 164 CP60 Mobile Computer (CE) Reference Manual PAN SERVICE To use personal area network (PAN) service shared by the Bluetooth device to connect to the Internet: 1) On the Device page, double-tap the paired Bluetooth device to open a page showing its available services.
Page 165 Chapter 5 Radios SERIAL PORT SERVICE To use Serial Port Service: 1) On the Service page, check if the Bluetooth virtual COM port is occupied by the local SPP service (i.e. whether a green connection icon is present). If so, tap and hold the service and select Unload in the pop-up menu.
Page 166 CP60 Mobile Computer (CE) Reference Manual 2) On the Device tab, double-tap the paired device to open a page showing the available services for that device. 3) Tap and hold Serial Port Service and select Connect in the pop-up menu.
Page 167 Chapter 5 Radios 4) By default, the mobile computer uses COM6 as the Bluetooth SPP COM port. Tap OK in the pop-up window to confirm. 5) A connection icon appears to indicate that serial port service is now active.
Page 168 CP60 Mobile Computer (CE) Reference Manual BLUETOOTH ACTIVESYNC To create ActiveSync connection between your PC and mobile computer via Bluetooth, first you will need to configure Bluetooth settings on your PC. 1) On your PC, configure necessary Bluetooth settings, such as turn Bluetooth discovery on, allow other Bluetooth devices to connect to the PC, and add a COM port for incoming connection.
Page 169 Chapter 5 Radios 3) On the mobile computer, make sure Serial Port Service is enabled in BT Manager. 4) On the Device page, double-tap your PC to view its available services. 5) Tap and hold Serial Port Services and select ActiveSync via BT in the pop-up menu. The mobile computer then connects to your PC via ActiveSync.
Page 170: Re-Connection
CP60 Mobile Computer (CE) Reference Manual 5.3.9. RE-CONNECTION By default, BT-Connect will automatically re-connect to the previous services the next time the mobile computer goes through a Bluetooth power cycle. The preferred devices and services will also be reflected on the Preference tabbed page of Manager.
Page 171: Preferred Services
Chapter 5 Radios 5.3.10. PREFERRED SERVICES On the Device tabbed page in BT-Connect, double-tap the preferred device to view its available Bluetooth service(s). Example Service Status Settings in BT-Manager The service is re-connected ( ). Last Connection = Y (on the Preference Tab) The service is available for re-connection.
Page 172: Manage Local Services
CP60 Mobile Computer (CE) Reference Manual 5.3.11. MANAGE LOCAL SERVICES LOAD/UNLOAD SERVICE You may select to load or unload a certain service. When a service is unloaded, it will become unavailable to paired Bluetooth devices. When it is re-loaded, it will become available once more.
Page 173 Chapter 5 Radios CHANGE LOCAL PATH For File Transfer and Object Push services, you may change the path for file exchange. 1) On the Service page, tap and hold an item to open a pop-up menu. Select Change Local Path in the pop-up menu and enter an inbox storage path. 2) Tap OK to confirm the change.
Page 174: Bt Manager
CP60 Mobile Computer (CE) Reference Manual 5.3.12. BT MANAGER Advanced Bluetooth settings regarding Bluetooth reconnection, Bluetooth inquiry time and more can be adjusted using BT Manager. 1) Tap Start | Settings | Control Panel | BT Manager Tap the Bluetooth icon on the Wireless Manager settings page.
Page 175 Chapter 5 Radios GENERAL TAB This page sets whether to allow reconnection of Bluetooth services and auto-inquiry of Bluetooth devices. Tap to restore default settings Tap to save changes Setting Description Allow to resume last service Select to automatically re-connect to all previous Bluetooth services after the mobile computer resumes from warm boot/cold boot, or goes through a Bluetooth power cycle.
Page 176 CP60 Mobile Computer (CE) Reference Manual PREFERENCE TAB BT Manager helps sort out preference for all remote services which were previously connected/disconnected. Select a desired service type from the drop-down menu: Headset/Handsfree Others (FTP, OPP, and DUN) MANAGING BLUETOOTH SERVICES Bluetooth devices which deliver the selected service type will be shown in the content field, including service/device icons, device names, and default connection settings (Last Connection and Auto Inquiry).
Page 177 Chapter 5 Radios CONFIGURING CONNECTION SETTINGS Change the connection preference for a specific service by enabling (selecting Y) or disabling (selecting N) the last two columns, Last Connection and Auto Inquiry. If you select Y for Last Connection or Auto Inquiry, “Allow to resume last service” and “Auto Inquiry”...
Page 178 CP60 Mobile Computer (CE) Reference Manual SAVING PREFERENCE CHANGES After making changes to preference settings, tap Apply. A warning dialog will show reminding that for the settings to take effect, you will need to restart Bluetooth power. Proceed to perform a Bluetooth power cycle as in Turn On/Off Bluetooth.
Page 179 Chapter 5 Radios ABOUT TAB This page delivers version and copyright information about the software.
Page 180: Use Gps
GPS relies on the satellites covering the sky around the world to pinpoint your whereabouts. A location-aware application is necessary, such as CipherLab’s GPS Viewer for NMEA-based location discovery. There are other applications downloadable from Internet. Download “.cab”-suffixed programs that confirm the compatibility with Windows Embedded Compact 6.0.
Page 181: More Applications
Chapter 6 MORE APPLICATIONS Aside from the dedicated Reader Configuration which empowers the mobile computer’s with a specialty in data capture as mentioned in Data Capture, more manufacturer-developed applications are preinstalled to strengthen user’s system management and make the mobile computer more eligible. These applications include: Applications Description...
Page 182: Button Assignment
CP60 Mobile Computer (CE) Reference Manual 6.1. BUTTON ASSIGNMENT Button Assignment can re-define the functions of physical keys so that they trigger different actions. Settings made to one or more keys can be saved as a profile, allowing users to switch conveniently in between different sets of settings.
Page 183: Redefine Keys
Chapter 6 More Applications 6.1.2. REDEFINE KEYS To assign a new function for a re-definable key: 1) Launch Button Assignment as described in Launch Button Assignment. 2) Scroll to the button you would like to re-define, and tap twice on the icon or text. Settings page for that button will open showing four options to set button function.
Page 184 CP60 Mobile Computer (CE) Reference Manual DISABLE/ENABLE KEY FUNCTION The last column in the Device Setting list gives an overview of key status. Users can disable or enable a key by giving a single tap on this column. By disabling keys, keys are “locked” as no actual function will take place when they are pressed.
Page 185: Main Menu
Chapter 6 More Applications 6.1.3. MAIN MENU When the main menu button is tapped, an option menu opens providing the following functions: Item Description User Profile Displays the existing profiles (not including default settings), and a toolbar to manage profiles: Toolbar icon Description Applies the selected profile.
Page 186 CP60 Mobile Computer (CE) Reference Manual MANAGE PROFILES CREATE PROFILE To create a new profile: 1) Load factory default settings, or read current settings from device first. 2) Modify the settings directly according to your needs, then tap to open a page where you can enter a name for the new profile.
Page 187 Chapter 6 More Applications Browse to the profile and tap to have it imported Select the profile you wish to export, then tap to enter export settings. Specify the location and file type for the profile to export Enter a name for the profile to export Note: The All Folders directory refers to all folders under My Device\My Documents.
Page 188 CP60 Mobile Computer (CE) Reference Manual READ/WRITE SETTINGS Use Read from device and Write to device to read the current settings on the device, or write the newly changed settings to the device in order for them to take effect. See Main Menu for when to use these options.
Page 189: Keypad Modes
Chapter 6 More Applications 6.1.4. KEYPAD MODES Both the numeric and QWERTY keypad provide two different modes, normal mode and function mode. To enable the function mode, simply press the Function key . For behaviors of the Function key, see Function Key.
Page 190 CP60 Mobile Computer (CE) Reference Manual 1, 2, 3.….9, 0 [-] Hyphen F1-24 User Define [.] Period key [#] Number Decrease Backlight Brightness Keys 1, 2, 3.….9, 0 F1-12...
Page 191 Chapter 6 More Applications QWERTY KEYPAD Special options Button Normal mode Function mode General options (Normal mode only) Answer Call / Start Menu Answer Call / Send Send End (Call) Start Menu End (Call) Scan Camera Home Scan + User define Left Left Scan Camera...
Page 192 CP60 Mobile Computer (CE) Reference Manual Keys A-Z F1-24 Note: (1) Direct keys (scan key, side trigger keys, volume up/down keys, Application key) on the mobile computer are available for re-assigning only under normal mode. (2) Several of the direct keys provide special functions under normal mode. These special functions include Camera and Scan + User Define.
Page 193: Gps Viewer
Chapter 6 More Applications 6.2. GPS VIEWER The mobile computer includes a GPS module (GPS hardware). This module communicates with the Global Positioning System and discovers your location on earth if it has a piece of GPS software to work with. The GPS module turns on automatically once GPS software launches on the mobile computer.
Page 194 CP60 Mobile Computer (CE) Reference Manual Item Description Date, Time Current date and time. Longitude, Latitude, Altitude Together they deliver the user’s location on earth. PDOP Positional (3D) Dilution of Precision, an indicator about the relationship between the error in user position and the error in satellite position.
Page 195: View Nmea-Based Data
Chapter 6 More Applications 6.2.2. VIEW NMEA-BASED DATA The data standard for GPS communication is NMEA. NMEA uses a simple serial protocol to define data syntax. GPS Viewer enables viewing such NMEA data streamed from GPS hardware to software (the application layer). To view NMEA data: 1) Launch GPS Viewer as described in Launch GPS Viewer.
Page 196: Signature Utility
CP60 Mobile Computer (CE) Reference Manual 6.3. SIGNATURE UTILITY Signature utility captures, views and edits signature files. 6.3.1. LAUNCH SIGNATURE UTILITY To launch Signature utility: 1) Tap Start | Programs | Signature Signature utility opens showing a toolbar along the top and a signing area within its window.
Page 197: Capture Signature
Chapter 6 More Applications 6.3.2. CAPTURE SIGNATURE To capture a signature: 1) Launch Signature utility as described in Launch Signature Utility. Signature utility launches. 2) Use the stylus to sign a name in the signing area. Put your name in the signing area 3) Tap icon to save the signature as an image in BMP, JPG or Locus format.
Page 198: View Or Edit Existing Signatures
CP60 Mobile Computer (CE) Reference Manual 6.3.3. VIEW OR EDIT EXISTING SIGNATURES To view the existing signature(s) on the storage of the mobile computer: 1) Launch Signature utility as described in Launch Signature Utility. Signature utility launches. 2) Tap icon on toolbar. The utility opens a screen allowing users to select the location and file type of the signature to view.
Page 199: Preferences
Chapter 6 More Applications 6.3.4. PREFERENCES The utility supports preferences settings which change the utility’s behaviors when it is used. Users are able to change the size and color of the signing pen stroke, and customize the background color of the signing area. To access the utility’s preferences settings: 1) Launch Signature utility as described in Launch Signature...
Page 200 CP60 Mobile Computer (CE) Reference Manual...
Page 201: Manage Mobile Computer
Chapter 7 MANAGE MOBILE COMPUTER This chapter guides you to the system settings featured by the OS. Access these settings to define how the mobile computer looks, sounds, stores/secures your data, manages the applications, or exchanges data with your networks or other devices. This chapter also includes the process for updating the OS image.
Page 202: Update Os Image
OS image upgrade helps optimize the mobile computer’s performance and functionality. The upgrade relies on CipherLab’s OS Update Tool, a utility to run on your PC to get the job done. This utility brings the upgrades of OS image and splash (booting logo) to the mobile computer.
Page 203: Control Panel
Chapter 7 Manage Mobile Computer 7.2. CONTROL PANEL To access control panel settings: Tap Start | Settings | Control Panel to display a window listing all the programs installed on the mobile computer. Icon Description BACKLIGHT SETTING Sets screen and keypad timeout and brightness. Four tabs are featured – Brightness, Battery Power, External Power, and Profile.
Page 204 CP60 Mobile Computer (CE) Reference Manual External Power Sets the screen backlight timeout on external power and whether to trigger screen/keypad light up upon pressing a key. Option Default Settings Turn off LCD backlight if device is not used Checked; for: 10 min Turn off keypad backlight if device is not...
Page 205 Chapter 7 Manage Mobile Computer DATE/TIME Sets RTC time, calendar and time zone. Note: RTC time can be reserved for approximately 60 days on the mobile computer after the main battery pack has been removed. DIALING Dials up the connection and configure settings for modem communication. (Not available for now).
Page 206 CP60 Mobile Computer (CE) Reference Manual BTPAN1 (via Bluetooth; option shows only when Bluetooth power is enabled in RF Manager) AX88772 (via Ethernet; option shows when the mobile computer is seated onto the 4-slot Terminal Cradle) OWNER Records information about the mobile computer’s owner, owner notes, and network PASSWORD Sets a password to secure the mobile computer upon power up or awake from suspension.
Page 207 Chapter 7 Manage Mobile Computer REMOVE PROGRAMS Views and removes non-inherent applications installed on the mobile computer. See also Uninstall Applications. SCREEN ROTATION Selects the modes to enable for screen orientation, and whether to suspend the mobile computer when it is facing down. Tap each of the following labels to enable/disable the given screen rotation mode.
Page 208 CP60 Mobile Computer (CE) Reference Manual Label Description System Shows total size and available size of storage under the System directory. USER_DATA Shows total size and available size of storage under the USER_DATA directory. Storage Card Shows total size and available size of storage under the Storage Card directory.
Page 209 Chapter 7 Manage Mobile Computer 0: None 1: (Reserved) 2: VGA WWAN 0: None 1: WWAN module 2: WWAN module 0: None 1: GPS Touch 0: None panel 1: 3.5” Touch panel Others 0: None (ExtUART) 1: IrDA 2: CIR 3: FIR TERMINAL SERVER CLIENT Logs onto a Windows Terminal Server or a remote computer through remote desktop...
Page 210 CP60 Mobile Computer (CE) Reference Manual VERSION VIEWER Lists version information of the applications, services and drivers installed on the mobile computer. VOLUME & SOUNDS Volume tab: Adjusts system sounds and volume for events, applications, notifications and stylus movements. Sounds tab: Changes event sounds to meet your preferences and save them as schemes.
Page 211: Connection Settings
Chapter 7 Manage Mobile Computer 7.3. CONNECTION SETTINGS To access connection settings: Tap Start | Settings | Control Panel | Network and Dial-up Connections. Tap Start | Settings | Network and Dial-up Connections. Icon Description MAKE NEW CONNECTIONS Tap to create a new connection which is not listed. USB SERIAL Sets serial profile for USB connection to a PC via ActiveSync.
Page 212 CP60 Mobile Computer (CE) Reference Manual WWAN Refers to connection via wireless wide area network (WWAN). To enable this function, enable cellular data in Start | Settings | Control Panel | Wireless Manager An icon is located on the taskbar. When connected to WWAN, the icon will change to When disconnected, the icon will return to SDCSD40N1...
Page 213 Chapter 7 Manage Mobile Computer The taskbar items deliver the following functions: Button Description Tap this button to open the Connection menu. The available options depend on the connection you select. Tap this button to toggle on/off the connection you select. This can be used for Enable/Disable or Connect/Disconnect.
Page 214: Taskbar And Start Menu Settings
CP60 Mobile Computer (CE) Reference Manual 7.4. TASKBAR AND START MENU SETTINGS To access taskbar and Start Menu settings: Tap Start | Settings | Taskbar and Start Menu. Tabbed page Setting Description General Always on top Select to keep the taskbar at the top of the screen, even when an application is open.
Page 215: Specifications
SPECIFICATIONS PLATFORM, PROCESSOR & MEMORY Operating System & CPU OS Version Microsoft Windows Embedded Compact 6.0 TI DM3730 1GHz Processor Memory 512MB DDR SDRAM Flash 4GB Flash ROM Expansion Slot One MicroSDHC card slot, supports up to 32GB COMMUNICATIONS & DATA CAPTURE Communications USB Host/Client USB 1.1 / USB 2.0...
Page 216: Electrical Characteristics
CP60 Mobile Computer (CE) Reference Manual ELECTRICAL CHARACTERISTICS Batteries Main Battery Pack Standard: 3.7V, 3600 mAh High Capacity: 3.7V, 4400 mAh Rechargeable Li-ion battery Charging time: approximately 4 hours for Standard battery and 6 hours for High Capacity battery Backup Battery 3.6V, 15 mAh Rechargeable Ni-MH battery Data retention for 30 minutes...
Page 217: Physical Characteristics
Specifications PHYSICAL CHARACTERISTICS Color Tap Screen Display Display 3.5” Transflective TFT-LCD, 65K colors, sunlight readable QVGA 240 (W) x 320 (H) Resolution Keypad Layout Numeric or QWERTY keypad Backlight White LED backlight for display and keypad Notifications Status LED Three LEDs for showing scanning good read, radio connection status and battery charging status Integrated with speaker Audio...
Page 218: Environmental Characteristics
IP65/67 per applicable IEC 60529 sealing specs Electrostatic Discharge ± 15 kV air discharge, ± 8 kV contact discharge Note: CipherLab will not be held responsible for the mobile computer’s malfunction incurred by the operation outside operating temperature range. PROGRAMMING SUPPORT Development Environment &...
Page 219: Accessories
Specifications ACCESSORIES Accessory Options Snap-on Charging and Communication Cable (USB or RS-232) Charging & Communication Cradle Pistol Grip Belt Holster for CP60 with Pistol Grip Belt Holster with Shoulder Strap for CP60 without Pistol Grip 4-slot Battery Charger Snap-On Car Charging Kit 4-slot Terminal Cradle Vehicle Mount Cradle...
Page 220 CP60 Mobile Computer (CE) Reference Manual...
Page 221: Scan Engine Settings
Appendix I SCAN ENGINE SETTINGS The CipherLab developed utility Reader Configuration configures the following reader types: 1D Laser (SE955) 1D Long Range Laser (SE965HP) 2D Imager (SE4500DL) The reader integrated on the mobile computer is either a 1D or 2D scan engine. When the physical scan key or side trigger is pressed, the mobile computer will read a printed barcode in position.
Page 222: Symbologies Supported
CP60 Mobile Computer (CE) Reference Manual SYMBOLOGIES SUPPORTED Depending on the scan engine integrated on the mobile computer, supported symbologies will differ as listed below. For details on configuring associated settings, refer to Appendix II and III. Laser Codabar Code 11 Code 39 Code 39 Trioptic Code 39...
Page 223 Appendix I Scan Engine Settings US Planet UK Postal EAN/UPC EAN-8 EAN-8 Extend EAN-13 Bookland EAN (ISBN) UCC Coupon Extended Code ISSN EAN UPC-A UPC-E Convert UPC-E to UPC-A UPC-E1 Convert UPC-E1 to UPC-A 2D Symbologies Aztec Data Matrix Maxicode MicroPDF417 MicroQR PDF417...
Page 224 CP60 Mobile Computer (CE) Reference Manual...
Page 225: Laser (Se955 & Se965Hp)
Appendix II LASER (SE955 & SE965HP) The tables below list the symbology settings for 1D laser scan engine (SE955) and 1D long range laser scan engine (SE965HP). SYMBOLOGY SETTINGS Symbology Description Default CODABAR CodaBar Codabar Checkbox to enable Codabar decoding. Enable Length option Sets the length of the Codabar symbols to decode.
Page 226 CP60 Mobile Computer (CE) Reference Manual Code 39 Code 39 Checkbox to enable Code 39 decoding. Enable Trioptic Code 39 Selects whether to decode Trioptic Code 39. Disable Trioptic Code 39 is a variant of Code 39 used in the marking of computer tape cartridges.
Page 227 Appendix II Laser (SE955 & SE965HP) Length option Sets the length of the Code 39 symbols to decode. Max / Min Length One Fixed length (Length 1) (4-55) Two Fixed lengths (Length 1>Length 2) Max / Min Length (range: 0-55; Length 1<Length 2) Any Length Interleaved 25 Interleaved 25...
Page 228 CP60 Mobile Computer (CE) Reference Manual Convert to UPC/EAN This only applies to GS1 DataBar-14 and GS1 DataBar Disable Limited barcodes not decoded as part of a Composite barcode. Convert to EAN-13 Strips the leading “010” from barcodes. The barcode must be composed of a leading “01” as the application identifier (AI) and a first digit of zero.
Page 229 Appendix II Laser (SE955 & SE965HP) UPC-A UPC-A Checkbox to enable UPC-A decoding. Enable Preamble Decide whether include UPC-A/UPC-E/UPC-E1 Transmit preamble System Character (and Country Code) in the data System being transmitted. Character No transmit: transmits none of the above Transmit System Character: transmits system number only Transmit Sys.
Page 230: Miscellaneous
CP60 Mobile Computer (CE) Reference Manual EAN Addon Option Decide whether to decode EAN-8, EAN-13 with addons Ignore Addon (including Addon 2 and 5). Ignore Addon Decode only with addons Auto-discriminate Addon When “Auto-discriminate” is applied, decide the number of Redundancy times of supplementary decoding the same barcode to count as a valid read.
Page 231: Aim Code Id - Modifier Characters
Appendix II Laser (SE955 & SE965HP) Code 39, Code 39 Full ASCII, Code 32 Code 128, Coupon (Code 128 portion) Data Matrix UPC/EAN, Coupon (UPC portion) GS1 DataBar (RSS) Codabar Code 93 Code 11 Interleaved 25 PDF417, Macro PDF417, Micro PDF417 QR Code, MicroQR Industrial 25 (Discrete 25), IATA 2 of 5 Maxicode...
Page 232 CP60 Mobile Computer (CE) Reference Manual (Discrete 25) UPC/EAN Standard data packet in full EAN country code format, which is 13 digits for UPC-A and UPC-E (not including addons). Standard data packet with two-digit or five-digit addons. EAN-8 data packet. A UPC-A with Addon 2 barcode, 012345678905-10, is transmitted to the host as a 18-character string, ]E3001234567890510.
Page 233 Appendix II Laser (SE955 & SE965HP) Scan engine is set for Basic Channel operation (no escape character transmission protocol). Data characters 92 not doubled. When decoders are set to this mode, unbuffered Macro symbols and symbols requiring the decoder to convey ECI escape sequences cannot be transmitted.
Page 234 CP60 Mobile Computer (CE) Reference Manual...
Page 235: Imager (Se4500Dl)
Appendix III 2D IMAGER (SE4500DL) The tables below list the symbology settings for 2D imager (SE4500DL). SYMBOLOGY SETTINGS 1D SYMBOLOGIES Symbology Description Default CODABAR CodaBar Codabar Checkbox to enable Codabar decoding. Enable Length option Sets the length of the Codabar symbols to decode. Max / Min Length One Fixed length (Length 1)
Page 236 CP60 Mobile Computer (CE) Reference Manual CODE 39 Code 39 Code 39 Checkbox to enable Code 39 decoding. Enable Trioptic Code 39 Selects whether to decode Trioptic Code 39. Disable Trioptic Code 39 is a variant of Code 39 used in the marking of computer tape cartridges.
Page 237 Appendix III 2D Imager (SE4500DL) Concatenation Sets whether to enable decoding ISBT-128 by performing Disable concatenation of ISBT data Disable: Does not perform concatenation Enable: Performs concatenation ISBT-128 barcodes. Auto-discriminate: Auto-discriminates between ISBT-128 barcodes which require concatenation and those which do not need concatenation. Redundancy Sets redundancy between 2-20.
Page 238 CP60 Mobile Computer (CE) Reference Manual Transmit Check Digit Decide whether to include the check digit in the data being Disable transmitted. COMPOSITE Composite CC-A/B Enable Composite Checkbox to enable Composite CC-A/B decoding. Disable CC-A/B Composite CC-C Enable Composite CC-C Checkbox to enable Composite CC-C decoding. Enable Composite TLC 39 Enable TLC 39...
Page 239 Appendix III 2D Imager (SE4500DL) Convert to UPC/EAN This only applies to GS1 DataBar-14 and GS1 DataBar Disable Limited barcodes not decoded as part of a Composite barcode. Convert to EAN-13 Strips the leading “010” from barcodes. The barcode must be composed of a leading “01” as the application identifier (AI) and a first digit of zero.
Page 240 CP60 Mobile Computer (CE) Reference Manual Netherlands KIX Code Enable Netherlands KIX Checkbox to enable Netherlands KIX Code decoding. Enable Code US Postnet Enable US Postnet Checkbox to enable US Postnet decoding. Enable US Planet Enable US Planet Checkbox to enable US Planet decoding. Enable UK Postal Enable UK Postal...
Page 241 Appendix III 2D Imager (SE4500DL) Preamble Decide whether include UPC-A/UPC-E/UPC-E1 Transmit preamble System Character (and Country Code) in the data System being transmitted. Character No transmit: transmits none of the above Transmit System Character: transmits system number only Transmit Sys. Character and Country Code: transmits system number and country code Convert to UPC-A The UPC-E barcode will be expanded into UPC-A format, and...
Page 242: Symbologies
CP60 Mobile Computer (CE) Reference Manual UPC Addon Redundancy When “Auto-discriminate” is applied, decide the number of times of supplementary decoding the same barcode to count as a valid read. Configurable between 2 and 30. 2D SYMBOLOGIES Symbology Description Default Aztec Aztec Selects whether to enable Aztec decoding.
Page 243: Miscellaneous
Appendix III 2D Imager (SE4500DL) Maxicode MicroPDF417 MicroPDF417 Selects whether to enable MicroPDF417 decoding. Disable Code 128 Emulation Transmit data from certain Micro PDF 417 barcodes as if it Disable was encoded in Code 128 barcodes. Transmit AIM code ID character in Miscellaneous options must be enabled first.
Page 244 CP60 Mobile Computer (CE) Reference Manual...
Page 245: Physical Keypad Reference Table
Appendix IV PHYSICAL KEYPAD REFERENCE TABLE NUMERIC KEYPAD Numeric keypad layout: USING ALPHA, SHIFT & FN KEYS Normal Mode Alpha Mode (Lowercase) Alpha Mode (Uppercase) Fn+Key Shift+Key only press press press press press press press press Shift+1 Shift+2 Shift+3 Shift+4 Shift+5 Shift+6 Shift+7...
Page 246 CP60 Mobile Computer (CE) Reference Manual Back Back Keypad Back Back Back Space Lock Space Space Space Space Back Back Back Back Back Back Light Light Light Light Light Light Send Send Start Send Send Send...
Page 247: Qwerty Keypad
Physical Keypad Reference Table QWERTY KEYPAD QWERTY keypad layout: USING ALPHA, SHIFT & FN KEYS Normal Shift+Key Fn (Orange)+Key Alpha (Blue)+Key < > “ Backspace Backspace Backspace Keypad Lock Backspace...
Page 248 CP60 Mobile Computer (CE) Reference Manual & & & & Space Space Space Space Space Enter Enter Enter Enter Enter HilightUp Page Up Down Down HilightDown Page Down Down Left Left HilightLeft Home Left Right Right HilightRight Right Backlight Backlight Backlight Backlight Backlight...

This manual is also suitable for:

Cp60 Cp60gce

CipherLab CP60G Reference Manual

Release Notes

Introduction

Use Mobile Computer

Data Capture

Camera

Operating System

Radios

More Applications

Manage Mobile Computer

Specifications

Scan Engine Settings

Laser (Se955 & Se965Hp)

Appendix III

Imager (Se4500Dl)

1 Symbologies

2 Symbologies

Physical Keypad Reference Table

Quick Links

Need help?

Questions and answers

Related Manuals for CipherLab CP60G

Summary of Contents for CipherLab CP60G

This manual is also suitable for:

Table of Contents