Basic Operations - Panasonic AW-HE130W Operating Instructions Manual

Basic operations

Camera menus are displayed on the monitor when the unit's settings are
to be selected.
The monitor is connected to the video signal output connector.
The basic camera menu operations involve displaying sub-menus from
the Top Menu items, and selecting settings on the sub-menus.
Some sub-menus have menu items for performing more detailed
settings.
The camera menu operations are conducted using the wireless remote
control.
If a controller is connected, they can also be conducted using the
controller.
<NOTE>
• Check that your controller is the following version. If the version is
older, consult your local dealer.
AW-RP50: Ver 3.00.00 or later
AW-RP120: Ver 2.00.00 or later
AK-HRP200: Ver 4.00-00-0.00 or later
Described below are the basic operations for changing the camera
menu item settings using the wireless remote control and controller
(AW-RP50, AW-RP120 or AW-HRP200).
Wireless remote control and controller operations
„
Camera menu operation Wireless remote control
Selecting a camera to
Press the <CAM1>, <CAM2>,
operate <CAM3>, or <CAM4> button.
Press and hold the <MENU>
Displaying the Top Menu
button for about 2 seconds.
Press the <4>, <5>, <b>, or
Selecting items
<a> button.
Displaying sub-menus Press the <M> button.
Returning to the previous Place the cursor on [Return],
menu and press the <M> button.
Place the cursor on the item
you want to change, <M>
button to make the setting
value blink.
Changing settings
Change the value using the
<4>, <5>, <b>, or <a>
button, and press the <M>
button to confirm.
Tap the MENU button (hold
Canceling setting
for less than 2 seconds) while
changes
the setting value is blinking.
Exiting camera menu Press and hold the <MENU>
operations button for about 2 seconds.
<NOTE>
• Perform the menu operations and exit from the menus using the controller which displayed the Top Menu.
If a menu operation has been performed or a menu has been exited using another controller, first display the Top Menu and exit from it using one
controller, and then display the Top Menu and exit from it using the other controller.
• The procedures used for this unit's menu operations may differ from the ones used for the convertible cameras and HD integrated cameras which
have already been released on the market. For details, refer to the Operating Instructions of the camera concerned.
• The response speed of the camera differs slightly depending on the controller used.
Only the steps taken using the wireless remote control will be
described here for the operations conducted to select and set
the items.
For details of the operations conducted using the controller,
substitute "controller" for "wireless remote control" when
reading the basic operations.
Refer to the operating instructions for the controller.
AW-RP50
Press the <CAMERA STATUS> Press the <CAMERA STATUS>
or <SELECTION> button. or <SELECTION> button.
Press and hold the <CAMERA Press and hold the <CAMERA
OSD> button for about 2 OSD> button for about 2
seconds. seconds.
Turn the <F1> dial. Turn the <F1> dial.
Press the <F1> dial. Turn the <F1> dial.
Place the cursor on [Return], Place the cursor on [Return],
and press the <F1> dial. and press the <F1> dial.
1. P ress the <F1> dial to make 1. P ress the <F1> dial to make
the setting value blink.
2. T urn the <F1> dial to change 2. T urn the <F1> dial to change
the setting value.
3. P ress the <F1> dial to 3. P ress the <F1> dial to
confirm the setting value
(blinking stops).
―
Press and hold the <CAMERA Press and hold the <CAMERA
OSD> button for about 2 OSD> button for about 2
seconds. seconds.
Controller
AW-RP120
1. P ress and hold the <SELECT>
(camera selection) button for
about 2 seconds.
→ T he camera number
2. P ress the lit <DATA
SET> buttons (<UP> and
<DOWN>).
→ Press the lit <DATA SET>
buttons (<UP> and <DOWN>)
to select the camera number.
3. Press the <SELECT>
(camera selection) button.
→ C ontrol of the selected
Press and hold the <CHARA/
MENU> button for about 2
seconds.
Turn the <SELECT> dial.
Press the <SELECT> dial.
Place the cursor on [Return],
and press the <SELECT> dial.
1. P ress the <SELECT> dial to
the setting value blink. make the setting value blink.
2. T urn the <SELECT> dial to
the setting value. change the setting value.
3. P ress the <SELECT> dial
confirm the setting value to confirm the setting value
(blinking stops). (blinking stops).
―
Press and hold the <CHARA/
MENU> button for about 2
seconds.
AK-HRP200
in the camera number
display area blinks.
camera is enabled.
―
37