Panasonic AW-HE130W Operating Instructions Manual page 20

Parts and their functions (continued)
Service switch settings
SW1 to SW3 (camera address setting switches)
Configure the camera address.
Set this to AUTO under normal circumstances. When cameras are set
to AUTO, addresses will be assigned to the cameras automatically
in response operation from the controller in the order in which the
cameras were connected.
To manually configure the address, set the switches as follows.
Address AUTO 1
SW1 OFF ON OFF
SW2 OFF ON ON
SW3 OFF ON ON
SW4 (communication format selection switch)
Selects the communication format.
When this is set to ON, standard serial communication is enabled.
When this is set to OFF, Panasonic's proprietary serial
communication is enabled.
SW5 (maintenance switch)
Fixed at OFF.
Do not change this switch setting.
SW6 (infrared output switch)
When this is set to ON, infrared output is enabled. The signal received
via the remote control sensor is output from pins 7 and 8 of the <RS-
232C IN> connector.
Signal output is disabled when this is set to OFF.
SW7 (communication baud rate switch)
When this is set to ON, the baud rate is 38400 bps.
When this is set to OFF, the baud rate is 9600 bps.
SW8 (communication connector switch)
When this is set to ON, the RS-422 is enabled.
When this is set to OFF, the RS-232C is enabled.
20
2 3 4 5 6
ON OFF ON OFF
OFF OFF ON ON
ON ON OFF OFF
Simultaneous output conditions for each video
„
format
z SDI/HDMI/VIDEO output
Format
HD/SDI 1080/59.94p
7
1080/50p
ON
1080/59.94i
OFF
1080/50i
OFF
1080/29.97psF
1080/25psF
1080/23.98psF
1080/29.97p
1080/25p
1080/23.98p
720/59.94p
720/50p
SD/SDI 480/59.94p
576/50p
480/59.94i
576/50i
*
1
480/59.94i and 576/50i is output to the VIDEO output regardless of
the format setting.
z IP video transmission output (1-/multi-channel display)
Resolution
Frame 60Hz
rate
50Hz
*
1
60 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
*
2
50 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
Setting
Resolution
Frame 60Hz
rate
50Hz
*
3
Different resolutions must be specified for JPEG CH1 / CH2 / CH3.
SDI HDMI
output output
 
 
 
 



 
 
 
 
 




1-channel display
1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90
(non-dependent on SYS format)
1 fps/2 fps/3 fps/5 fps/6 fps/10 fps/15 fps/30 fps/
60 fps
1
*
1 fps/2 fps/5 fps/10 fps/12.5 fps/25 fps/50 fps
Multi-channel display
H.264 CH1 H.264 CH2 H.264 CH3/
CH4
1920×1080 / 1920×1080 / 1280×720 /
1280×720 1280×720 / 640×360 /
640×360 / 320×180 /
320×180 / 160×90
160×90
60fps 5 fps/15 fps/ 5 fps/15 fps/
30 fps 30 fps
50 fps 5 fps/ 5 fps/
12.5 fps/ 12.5 fps/
25 fps 25 fps
VIDEO
output












1
 *
 * 1
2
*
JPEG CH1/
CH2/CH3 3
*
1920×1080 /
1280×720 /
640×360 /
320×180 /
160×90
1 fps/2 fps/
3 fps/5 fps/
6 fps/10 fps/
15 fps/30 fps
1 fps/2 fps/
5 fps/10 fps/
12.5 fps/
25 fps