1. Manuals
  2. Brands
  3. WebGate Manuals
  4. Recording Equipment
  5. i-Rec B104
  6. Installation manual

WebGate i-Rec B104 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
i-Rec B104
Installation Guide
(v 1.4)

Advertisement

Table of Contents
loading

Summary of Contents for WebGate i-Rec B104

  • Page 1 B104 Installation Guide (v 1.4)

  • Page 2: Fcc Compliance Statement

    - Consult the dealer or an experienced radio/TV technician for help. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries properly with regards to environmental considerations. WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 3: Important Notice

    Important Notice 1. When i-Rec B104 is in operation, do not place heavy monitors or other items on top of unit. Do not vertically stack more than four i-Rec B104s. 2. i-Rec B104 is not weatherproof. Therefore consider environmental specifications that are included in the manual.

  • Page 4: Table Of Contents

    Connecting i-Rec B104 to Network ................11 4.2.1. Connecting i-Rec B104 to PC directly ...............11 4.2.2. Connecting i-Rec B104 to Local Network............12 Setting i-Rec B104 & Getting an Image................13 Installing CamViewer II ..................13 5.1. 5.1.1. Installation of Software..................13 5.1.2.
  • Page 5 Sensor Input Port View ..................37 8.3.3. Connecting & Setting ..................37 8.3.4. Connecting sensors for 1.0 or below main version PCB of i-Rec B104 .... 38 8.4. Connecting Impedance Setup Switch for Video Input ..........39 8.5. Video Input......................39 APPENDIX ..........................

  • Page 6: Introduction

    Introduction 1. Key Features i-Rec B104 is a 4-channel box style Network DVR. It is an all-in-one system with a Web server of embedded Linux, a networking device, and a HDD (Removable). i-Rec B104 only needs designated power supply and network connection in order to operate.

  • Page 7: Supplied Accessories

    Introduction i-Rec B104 2. Supplied Accessories Unpack and check all items. 1. i-Rec B104 (1) 2. DC POWER SUPPLY (1) (110V ~ 220V) CD-ROM (INCLUDING CAMVIEWER 3. AC POWER CORD (1) AND OPERATING INSTRUCTIONS) (1) 5. ETHERNET CABLE (1, RED) 6.
  • Page 8 B104 Introduction 7. INSTALLATION GUIDE (1) 8. TERMINAL BLOCK (3) (8PIN x 2, 7PIN x 1) 9. HDD MOBILE RACK KEY (1) 10. SCREW (4) WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 9: Product Views And Description

    Introduction i-Rec B104 3. Product Views and Description (1) HDD mobile rack (2) Alarm output (3) Sensor input (4) Serial port (5) Video input (6) Impedance control switch (7) Ethernet (8) DC power WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 10: Installing & Connecting

    4. Installing i-Rec B104 This user’s guide describes the most two common network conditions for installing B-104: (1) i-Rec B104 and administrator’s PC uses fixed or private IP address. (2) Computers and B104 are connected directly or to local network.

  • Page 11: Connecting I-Rec B104 To Network

    Installing & Connecting i-Rec B104 4.2. Connecting i-Rec B104 to Network Connect i-Rec B104 to client’s PC directly with crossover cable or through HUB with direct cable. Please refer to the following figures. 4.2.1. Connecting i-Rec B104 to PC directly (1) Connect i-Rec B104 to client’s PC with crossover cable (Red Ethernet cable).

  • Page 12: Connecting I-Rec B104 To Local Network

    B104 Installing & Connecting 4.2.2. Connecting i-Rec B104 to Local Network (1) Connect B104 to HUB with direct cable (Ivory Ethernet cable). (2) Connect the supplied AC adaptor to B104. <Note> 1. To prevent damage to B104, connect power cable only after connecting Ethernet cable.

  • Page 13: Setting I-Rec B104 & Getting An Image

    Installing & Connecting i-Rec B104 5. Setting i-Rec B104 & Getting an Image The following procedure is for installing i-Rec B104 and checking basic operation. For more information, please refer to “CamViewer II User Guide”. 5.1. Installing CamViewer II 5.1.1. Installation of Software (1) Insert Setup CD-ROM into CD-ROM drive of administrator’s PC...

  • Page 14: Uninstalling

    B104 Installing & Connecting (5) Browse and choose a directory if the default directory is not preferred. Click the ‘Install’ button, after selecting a directory to install. (6) Click the ‘Close’ button after CamViewer II Setup Program is installed successfully.

  • Page 15: Connecting To I-Rec B104

    (3) Click the symbol ‘+’ on the left of “Local Area Cameras” to browse all the i-Rec B104s. (4) Click to select an i-Rec B104 to assign IP Address. The IP address of the selected i-Rec B104 will appear in the “Change IP” box.

  • Page 16: Setting Ip Address

    <Note> 1. Be careful on typing values into this menu. Without correct network address, nobody will be able to connect to i-Rec B104. 2. Refer to the User’s guide in setup CD-ROM to install i-RecB104 on Dynamic IP network environment.

  • Page 17: Setting Camera Input Channel

    <Note> 1. If channel is selected but the related camera is not connected, recording and monitoring performance will decrease. 2. i-Rec B104 can’t be used with both NTSC and PAL cameras connected simultaneously. WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 18: Checking Images Of I-Rec B104

    5.5 Checking Images of i-Rec B104 (1) Click the related ICON and run the “Monitor” program. (2) Click the “Cam Selection” button. (3) Select “B104” folder. (4) Select i-Rec B104 to view images. (5) Click “OK” button. (6) Select the “Cam connection” button. WEBGATE Inc.
  • Page 19 Installing & Connecting i-Rec B104 (7) Enter “User Name” and “Password” as “admin” / “admin”. (8) Click “Login” button to view images of connected channel. WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 20: Installing Hdd

    B104 Installing & Connecting 6. Installing HDD 6.1. Usable HDD (1) It is recommended to install only Maxtor brand HDD for i-Rec B104. Manufacturer: MAXTOR Series Model Name Size Series Model Name Size 6L040J(L)2 40GB 4G120J6 120GB DiamondMax DiamondMax...
  • Page 21 (2) Insert the key into the key hole of HDD rack and turn it counter clock-wise to release. (3) Pull the handle of HDD rack and remove the HDD case completely from i-Rec B104 rack. (4) Release the hook and open the cover by pulling lock as indicated in figure below.
  • Page 22 B104 Installing & Connecting (5) Connect data and power cables to HDD and screw down the HDD to rack. Then close the cover. (HDD needs to be fixed tightly with screws so that vibration does not damage hard drive.) <Note>...
  • Page 23 Installing & Connecting i-Rec B104 (6) Pull handle down and push the HDD case into the rack completely. (7) Insert the key and turn it clock wise to re lock the rack. (8) Check whether the newly installed HDD operates normally, refer to the “Image Recording &...

  • Page 24: Recording & Playback

    B104 Installing & Connecting 7. Recording & Playback After installing HDD, please follow below procedures at the ConfigStation program in order to record images into HDD 7.1 Setting HDD (1) Click the “HDD” tab. (2) Check the “HDD Enable” combo box and click “HDD Format…” button.

  • Page 25: Setting Time

    Installing & Connecting i-Rec B104 7.2. Setting Time (1) Click the “System” tab. (2) Configure the place, time, and date according to the configuration where the i-Rec B104 is installed. (3) Click “Apply” button. <Note> The B104 can be synchronized to the Administrator’s PC as long as PC is set for the same time zone.

  • Page 26: Setting Recording Schedule

    B104 Installing & Connecting 7.3. Setting Recording Schedule (1) Click “Schedule” tab. (2) Please click “Setup” button in the “Record Schedule” box to configure recording schedule of the channel to which camera is connected. (3) Set up the recording conditions in normal and event time and click the “OK” button.
  • Page 27 Installing & Connecting i-Rec B104 (4) Click “Apply” button after configuring each channel. WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 28: Playback

    (2) Click the button for camera selection on the lower right of the screen. (3) Select the B104 folder. (4) Select the i-Rec B104 in which images have been recorded. (5) Click “OK” button. (6) Click the camera connection button.
  • Page 29 Installing & Connecting i-Rec B104 (7) Input “admin” and “admin” in the log-in input box of “User Name” and “Password”. (8) Click “Login” button, and view the images recorded in i-Rec B104. WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 30: Input / Output

    B104 Installing & Connecting 8. Input / Output The electrical diagram of i-Rec B104 <Note> Trimming wire When connecting a wire to a terminal block, follow the instructions below. Note the different types of wire that can be used.

  • Page 31: Connecting Serial Port

    Installing & Connecting i-Rec B104 8.1. Connecting Serial Port 8.1.1. Specifications of Serial Port The followings are serial ports that can be used in i-Rec B104. Protocol Max. Distance Max. Driver/Receiver Remarks RS-232C About 15 m 1 Driver / 1 Receiver...

  • Page 32: Connecting & Setting Rs-485 Port

    Insert the wire as below and spin the screw of terminal block in a clockwise direction. 8.1.3.3. Setting Access i-Rec B104 with CamViewer program and configure RS232C port suitably after connecting to external device. 8.1.4. Connecting & setting RS-485 port RS-485 is used for controlling PTZ.

  • Page 33: Connecting & Setting Rs-422 Port

    Installing & Connecting i-Rec B104 8.1.4.2. Connecting 8.1.4.3. Setting Access i-Rec B104 with CamViewer program and configure RS485 port suitably after connecting with external device. 8.1.5. Connecting & setting RS-422 port 8.1.5.1. Diagram <Note> Some devices require connecting GND port of external device for stable operation.
  • Page 34 B104 Installing & Connecting 8.1.5.2. Connecting 8.1.5.3. Setting Access i-Rec B104 with CamViewer program and configure RS422 port suitably after connecting to external device. <Note> The supported PTZ Manufacturer Model Manufacturer Model Philips Auto Dome GAC-PT2 Philips TC8560X-4 Sony...

  • Page 35: Connecting Alarm Output

    Installing & Connecting i-Rec B104 8.2. Connecting Alarm Output 8.2.1. Specifications of Alarm Output In order to run alarm output of i-Rec B104 normally, the following conditions are required. Output Ch. 4Ch. Photo relay differential outputs Output type Dry contact Spec.
  • Page 36 Installing & Connecting 8.2.3.2. Connecting The above figure shows how to connect a warning light to i-Rec B104. For connecting wire, please refer to manual of related warning light and “Trimming wire” part of this manual. Insert the wire and spin the screw of terminal block with flathead “-“shaped driver.

  • Page 37: Connecting Sensor Input

    Installing & Connecting i-Rec B104 8.3. Connecting Sensor Input 8.3.1. Specifications of Sensor Input In order to run sensor input of i-Rec B104 normally, the following conditions are required. Input Ch. 4Ch. Photo coupler differential inputs Input type N.C. (Normal Close) type Spec.

  • Page 38: Connecting Sensors For 1.0 Or Below Main Version Pcb Of I-Rec B104

    Installing & Connecting 8.3.3.2. Connecting The above figure illustrates connecting a sensor to i-Rec B104. For connecting wires, please refer to manual of related sensor and “Trimming wire” part of this manual. Insert the wire and spin the screw of terminal block with flathead “-“shaped driver.

  • Page 39: Connecting Impedance Setup Switch For Video Input

    Installing & Connecting i-Rec B104 8.4. Connecting Impedance Setup Switch for Video Input When one video output is connected to several inputs (e.g. CCTV monitor, i-Rec) as below, the impedance of one input should be 75 ohm. The impedance will be set as 75ohm by selecting 75ohm.

  • Page 40: Appendix

    B104 Appendix APPENDIX APPENDIX WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 41: Frequently Asked Question (Faq)

    B104 is a 4-channel box style DVR with a Web server of embedded Linux, a networking device, and a HDD (HDD Rack). Since i-Rec B104 is a Web server, it does not need to be connected to other servers. By installing an i-Rec B104 in remote locations, you can remotely record and monitor the place.
  • Page 42 30 frames peer seconds since transmission speed also depends on user PC’s performance and network line capacity. i-Rec B104 can transmit as well as record at the same time. If i-Rec B104 records images from 4 channels and transmits live images from all 4 channels, the transmission speed can be lower compared with another i-Rec B104 that does not record any image but transmits images from only 1 channel.

  • Page 43: About I-Rec B104 Installing

    #1.2. About i-Rec B104 Installing What network line is to be used? For local use, i-Rec B104 can be installed on any local area network (LAN). For remote use, network lines on a dedicated line (fix IP or dynamic IP address), xDSL line and Cable Modem line are to be used.
  • Page 44 When the network only consists of private IP addresses, can i-Rec B104 be connected on the network? i-Rec B104 can be connected to LAN having only private IP addresses, as long as the i-Rec B104 is accessed by local users. However, the whole network can be down, if the network’s equipment such as a hub is not sufficient to support all the devices appropriately.
  • Page 45 Which pan/tilt/zoom mechanism can be installed with i-Rec B104? i-Rec B104 has function to control pan/tilt/zoom mechanism; the mechanism is installed to i- Rec B104 through its port in the rear. i-Rec B104 has three pairs of pins; RS-232 and RS- 485/ RS-422 i-Rec B104 contains some protocols (Please refer to “<Note>...

  • Page 46: Utilizing Ip Addresses On Local Network

    B104 Appendix #2. Utilizing IP Addresses on Local Network #2.1. Introduction Most of our business is done via Internet. We play with information by transmitting through e- mails and searching the Internet. IP address is what we utilize to access the Internet.

  • Page 47: C-Class Network

    255 is used for Broadcast address. Therefore the numbers from 2 to 244 are IP addresses that can be assigned to WebEye, i-Rec B104, PC etc. Network ID: It is to identify a network. Generally the first number is assigned as Network ID.
  • Page 48 B104 Appendix (2) To use as two sub-networks (1/2 + 1/2) Sub-Network ID: xxx.xxx.xxx.0 Gateway Address: xxx.xxx.xxx.1 Subnet Mask: 255.255.255.128 Broadcast Address: xxx.xxx.xxx.127 IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.126 Sub-Network ID: xxx.xxx.xxx.128 Gateway Address: xxx.xxx.xxx.129 Subnet Mask: 255.255.255.128 Broadcast Address: xxx.xxx.xxx.255 IP Addresses: xxx.xxx.xxx.130 –...
  • Page 49 Appendix i-Rec B104 (4) To use as four sub-networks (1/4 + 1/4 + 1/4 + 1/4) Sub-Network ID: xxx.xxx.xxx.0 Gateway Address: xxx.xxx.xxx.1 Subnet Mask: 255.255.255.192 Broadcast Address: xxx.xxx.xxx.63 IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.62 Sub-Network ID: xxx.xxx.xxx.64 Gateway Address: xxx.xxx.xxx.65 Subnet Mask: 255.255.255.192 Broadcast Address: xxx.xxx.xxx.127...

  • Page 50: Setting The Fixed Ip Address On Pc

    B104 Appendix #3. Setting the fixed IP address on PC The following shows how to set the fixed IP address on PC with Microsoft’s Windows98. (1) After selecting “Network Neighborhood” of desktop, press the right button of mouse and select “Properties”.
  • Page 51 Appendix i-Rec B104 (3) Enter Gateway as following, and press the “Add” button. (4) Enter IP address and Subnet Mask as following. WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 52: Crs Help

    B104 Appendix #4. CRS Help #4.1. When using ADSL When you can’t access B104 connected to ADSL, check the followings. (1) Configure each values at xDSL (PPPoE) and CRS of “Network” tab. WEBGATE Inc. 2003. 06. 30 (v 1.4)
  • Page 53 Appendix i-Rec B104 (2) Check whether B104’s IP address is same with PC’s IP address or not. For example, if B104’s IP address is 211.53.133.181(Figure 1) and PC’s IP address is 211.53.133.73(Figure 2), connection will be failed. If network address part of IP address is same like ‘211.53.133’, packets that should be transmitted to PC can be transmitted to B104.
  • Page 54 B104 Appendix (3) In this case, you have only to change network address part of B104’s IP address after accessing B104 through local network. For example, you have to change 211.53.133.181 into 211.53.0.181. (4) After changing network value, reboot B104.

  • Page 55: When Resetting Local Network From Adsl

    (1) Stop connecting ADSL. When connecting to local network again, B104 can’t be connected as followings. (The following example shows when Group ID is set as webgate.) [Figure 1] When connecting B104 that is registered at My Cameras [Figure 2] When connecting B104 that is registered at Group ID of CRS WEBGATE Inc.
  • Page 56 B104 Appendix (2) In this case, delete the current Group ID (webgate) of CRS. If same camera is also registered in My Cameras, both of them should be deleted. When deleting all in both menus, the B104 shows in Local Area Cameras automatically.
  • Page 57 Appendix i-Rec B104 (3) User can register the B104 of ‘Local Area Cameras’ to ‘My Cameras’ directory by dragging. At this time, you should change its IP within the related local network. WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 58: When Using Cable Modem

    B104 Appendix #4.3. When using Cable modem Check if DHCP Enable is selected. You should not select xDSL (PPPoE). WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 59: Upgrading I-Rec B104 Firmware

    #5.1. Connecting i-Rec B104 to PC Connect i-Rec B104 to PC with a crossover cable directly. This connection is recommended. It is also possible to connect i-Rec B104 to a PC through a HUB with direct cable. <Note> You may also do the process on a remote network, but it is not recommended.
  • Page 60 (4) After updating process is completed, it is recommended to reboot i-Rec B104 to make it operate properly. (5) If you have another i-Rec B104 to upgrade, follow the same process from (1) to (4). If not, quit the program by clicking ‘Exit’ button.

  • Page 61: Using Cd-Rom

    Appendix i-Rec B104 #6. Using CD-ROM Within the supplied CD-ROM DISC, there are “i-Rec B104 User’s Guide” and several programs for using i-Rec B104. Contents of CD- ROM CamViewerII x.x.x.exe : i-Rec Setup program ar510enu.exe : Acrobat reader program i-Rec B104 Installation Guide v1.4.PDF : i-Rec B104 Installation Guide CamViewer II User's Guide v1.4.PDF...

  • Page 62: Specifications

    B104 Appendix #7. Specifications General 32bit RISC Embedded Processor FLASH MEMORY MAIN MEMORY 16MB Embedded Linux NTSC or PAL video format are supported VIDEO CHANNEL 4Ch. video input STORAGE Internal 3.5” IDE HDD 1EA Compression ALGORITHM Wavelet RESOLUTION 720x486, 720x243, 360x243, 180x121, 90x60 (NTSC)
  • Page 63 Appendix i-Rec B104 Environments OPERATION TEMPERATURE 5°C ~ +45°C STORAGE TEMPERATURE -25°C ~ +55°C OPERATION HUMIDITY 30% ~ 80% R.H (free of condensation) STORAGE HUMIDITY 93% R.H and less (free of condensation) Additional function & I/O ADDITIONAL FUNCTION Motion detection Image quality Control (10 Levels) 4.5 MB fresh memory for homepage customization...
  • Page 64 B104 Appendix Mechanical DIMENSION 306mm X 298 mm X 67mm WEIGHT 3160g (without HDD) WEBGATE Inc. 2003. 06. 30 (v 1.4)

  • Page 65: Webgate Inc

    6F, Hanlim Venture Town Bldg., 689-6, Geumjeong-dong, Gunpo- si, Gyeonggi-do, Korea (435-862) Tel : (82-31) 428-9300 Fax : (82-31) 428-3955 Sales@webgateinc.com www.webgateinc.com WEBGATE Inc. USA 465 Halstead St. Suite 110, Pasadena, California 91107, USA Tel : (626) 351-6500 Fax : (626) 351-3660...

Table of Contents