Page 2
Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.
Industry Canada ................................26 Brazil Approval................................27 Telecom Requirements for the United States ......................27 47 CFR – FCC Part 15 ..............................27 47 CFR Part 68 Telecom ............................... 27 New Zealand Telecom Warning Notice ........................29 Multi-Tech Systems, Inc. RJModem Developer's Guide...
Page 4
Restriction of the Use of Hazardous Substances (RoHS) ....................32 Information on HS/TS Substances According to Chinese Standards ................33 Information on HS/TS Substances According to Chinese Standards (in Chinese) ............34 Index ................................35 Multi-Tech Systems, Inc. RJModem Developer's Guide...
Chapter 1 – RJModem Hardware The Multi-Tech RJModem creates communication-ready devices by integrating modem functions into the most compact, integrated device. The first-of-its-kind RJ11 form factor includes the controller, data pump, and DAA giving you the ability to integrate dial-up connectivity into any product design. With minimal engineering effort, the RJModem instantly adds global communication capabilities, enhancing the end user experience and increasing product value.
Developer Guide. AT Commands Use AT Commands to configure your RJModem. Refer to the RJModem and SocketModem IP AT Command Reference Guide, (part number S000364) available on the Multi-Tech Web site at www.multitech.com/setup/product.go. Multi-Tech Systems, Inc. RJModem Developer's Guide...
Installation in a vehicle or other outdoor locations has not been evaluated by UL. UL Certification does not apply or extend to use in vehicles or outdoor applications or in ambient above 40° C.” Répertorié UL à 40° C, limitée par la puissance d'alimentation. Multi-Tech Systems, Inc. RJModem Developer's Guide...
à utiliser dans des véhicules ou les applications en extérieur ou dans ambiante dépasse 40 » ° C. Dimensions for Board Mounting and Panel Mounting Board Mounting Dimensions Bottom View Top View Multi-Tech Systems, Inc. RJModem Developer's Guide...
Chapter 1 – RJModem Hardware Panel Mounting Note: Screws, bracket and ribbon cable are included in the panel-mounting kit. Attaching the Mounting Bracket Multi-Tech Systems, Inc. RJModem Developer's Guide...
Notes: Surface mount connectors are approved in place of soldering the unit to the motherboard. Follow the "Pass Through" footprint instructions on the part data sheets. The following are recommended by Multi-Tech: www.samtec.com SAMTEC: SMM-107-02-S-D-(other option) or equivalent SAMTEC: CLT-107-02-(plating option)-D-(other option) or equivalent...
Chapter 1 – RJModem Hardware Pin Out Dimensions PCB Footprint or Board Lay-out (Note: This is the PCB top view) Pin Descriptions Top View PCB Top Surface Front RJModem Jack Opening Multi-Tech Systems, Inc. RJModem Developer's Guide...
Page 13
Speaker. Call Progress signaling on MT5656RJ is a square wave output that can be optionally connected to a low-cost single-ended speaker; e.g., a sounducer or an analog speaker circuit. RXCLK Receive Data Sync Clock. RX synchronous data clock for sync data mode. More information below. Multi-Tech Systems, Inc. RJModem Developer's Guide...
TXCLK and the RXCLK pins on the RJModem; you can use a 9-pin interface. Use the &M command to set Synchronous mode. To save the current (active) configuration (profile), use the &W command. See the RJModem AT command guide available on the Multi-Tech Web site. Using &Q Command to Control the Connection Modes This command is an extension of the &M command.
<value> Decimal number corresponding to the selected profile. 0 – Store the current configuration as profile 0. 1 – Store the current configuration as profile 1. Result Codes OK <value> = 0 or 1. ERROR Multi-Tech Systems, Inc. RJModem Developer's Guide...
Handle all electronic devices with certain precautions to avoid damage due to the accumulation of static charge. Although input protection circuitry has been incorporated into the devices to minimize the effect of this static buildup, proper precautions should be taken to avoid exposure to electrostatic discharge during handling and mounting. Multi-Tech Systems, Inc. RJModem Developer's Guide...
If this jumper is set incorrectly, damage to the RJModem and/or the Test/Demo card can result. Caution – Use only the provided Multi-Tech Systems, Inc. transformer with the Test/Demo board. Use of any other power source voids the warranty and can damage the Test/Demo board and the RJModem. The transformer connector is keyed to prevent improper connection to the Test/Demo board.
Chapter 1 – RJModem Hardware Developer Board Schematics To view the text and numbers, increase the viewing percentage to 150% or print the page. Multi-Tech Systems, Inc. RJModem Developer's Guide...
Page 21
Chapter 1 – RJModem Hardware To view the text and numbers, increase the viewing percentage to 150% or print the page. Multi-Tech Systems, Inc. RJModem Developer's Guide...
Page 22
Chapter 1 – RJModem Hardware To view the text and numbers, increase the viewing percentage to 150% or print the page. Multi-Tech Systems, Inc. RJModem Developer's Guide...
Lay out the highest frequency signal traces next to the ground grid. If a multilayer board design is used, make no cuts in the ground or power planes and be sure the ground plane covers all traces. Multi-Tech Systems, Inc. RJModem Developer's Guide...
Distribute high frequency signals continuously on a single trace rather than several traces radiating from one point. EMI Filtering The RJModem includes EMI filtering as illustrated in the following schematic: Multi-Tech Systems, Inc. RJModem Developer's Guide...
Éviter d'utiliser le téléphone pendant un orage électrique. Il peut y avoir un risque de choc électrique causé par la foudre. ● N'utilisez pas un téléphone à proximité d'une fuite de gaz. ATTENTION: Pour réduire les risques d’incendie, utiliser uniquement des conducteurs de telecommunications 26 AWG au de section supérleure. Multi-Tech Systems, Inc. RJModem Developer's Guide...
Multi-Tech's analog dial-up global RJModem is designed and approved for connection to the public switched telephone network in more than 50 countries or regions worldwide. Multi-Tech's RJModem is approved as host independent, which means our certification efforts can be transferred directly to your end product.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable 47 CFR Part 68 rules and requirements adopted by the ACTA. It’s designed to be connected to a compatible modular jack that is also compliant. Multi-Tech Systems, Inc. RJModem Developer's Guide...
Page 28
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. Unauthorized repairs void registration and warranty.
For correct operation, total of the RN’s of all devices connected to a single line at any time should not exceed 5. Russian Statement MT5656RJ is Russia approved, Declaration of Conformity # Д-ТФ-0708 valid till 20.02.2017 (for MT5656RJ). Multi-Tech Systems, Inc. RJModem Developer's Guide...
The above country-specific examples do not cover all countries with specific regulations; they are included to show you how each country may differ. If you have trouble determining your own country's requirements, check with Multi-Tech's Technical Support for assistance. International Modem Restrictions Some dialing and answering defaults and restrictions may vary for international modems.
Substances) complements the WEEE Directive by banning the presence of specific hazardous substances in the products at the design phase. The WEEE Directive covers all Multi-Tech products imported into the EU as of August 13, 2005. EU-based manufacturers, distributors, retailers and importers are obliged to finance the costs of recovery from municipal collection points, reuse, and recycling of specified percentages per the WEEE requirements.
Certificate of Compliance 2011/65/EU Multi-Tech Systems confirms that its embedded products comply with the chemical concentration limitations set forth in the directive 2011/65/EU of the European Parliament (Restriction of the use of certain Hazardous Substances in electrical and electronic equipment - RoHS) These Multi-Tech products do not contain the following banned chemicals ●...
Information Products (EIP) # 39, also known as China RoHS, the following information is provided regarding the names and concentration levels of Toxic Substances (TS) or Hazardous Substances (HS) which may be contained in Multi-Tech Systems Inc. products relative to the EIP standards set by China’s Ministry of Information Industry (MII).
Chapter 3 – Waste Electrical and Electronic Equipment (WEEE) Statement, RoHS, Chinese Standards Information on HS/TS Substances According to Chinese Standards (in Chinese) 依照中国标准的有毒有害物质信息 根据中华人民共和国信息产业部 (MII) 制定的电子信息产品 (EIP) 标准-中华人民共和国《电子信息产品污染控制管理办法》(第 39 号),也称作中国 RoHS,下表列出了 Multi-Tech Systems, Inc. 产品中可能含有的有毒物质 (TS) 或有害物质 (HS) 的名称及含量水平方面的信息。 有害/有毒物质/元素 铅 汞 镉...