Related Manuals for DFI Q7-100
Summary of Contents for DFI Q7-100
- Page 1 Q7-100 Qseven Carrier Board User’s Manual A19810337 Chapter 1 Introduction www.dfi.com...
-
Page 2: Copyright
Copyright FCC and DOC Statement on Class B This publication contains information that is protected by copyright. No part of it may be re- This equipment has been tested and found to comply with the limits for a Class B digital produced in any form or by any means or used to make any transformation/adaptation without device, pursuant to Part 15 of the FCC rules. -
Page 3: Table Of Contents
Table of Contents Internal I/O Connectors ............S/PDIF Connector ..................18 LVDS LCD Panel Connector and LCD/Inverter Power Connector ..... 19 Digital I/O Connector and Digital I/O Power Connector......... 20 Expansion Slots ..................20 Copyright ......................2 SATA (Serial ATA) Connectors ..............21 Cooling Fan Connectors................ -
Page 4: About This Manual
About this Manual Static Electricity Precautions An electronic file of this manual is included in the CD. To view the user’s manual in the CD, It is quite easy to inadvertently damage your PC, system board, components or devices even insert the CD into a CD-ROM drive. -
Page 5: About The Package
About the Package The package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance. • One Q7-100 board • One Serial ATA data cable • One IO shield •... -
Page 6: Chapter 1 - Introduction
Chapter 1 Chapter 1 - Introduction IO Connectors • 2 connectors for 4 external USB 2.0/1.1 ports Specifications • 1 LPC connector • 1 I C connector • 1 CAN-bus connector Graphics • Chrontel CH7317B (SDVO to RGB DAC) • 1 LVDS LCD panel connector - 18/24-bit single channel Audio •... -
Page 7: Chapter 2 - Hardware Installation
Chapter 2 Chapter 2 - Hardware Installation Block Diagram Board Layout Interface GLAN Super IO (RTL8111DL) GPIO 8 Ports Select (JP16) COM0 RS232 Chassis Select (JP23) Intrusion DIO Power H/W Monitor SPI Flash Select (J14) GLAN BIOS SDVO CASE Open W83627DHG-P Interface CH7317... -
Page 8: Mechanical Diagram
Chapter 2 Mechanical Diagram 10.16 10.16 0.00 22.86 46.94 54.80 68.30 122.30 154.94 154.94 160.02 160.02 Chapter 2 Hardware Installation www.dfi .com... -
Page 9: Jumper Settings
Chapter 2 Jumper Settings USB Power Select COM 0 RS232 Select USB 0-1 COM 0 (JP1) 1-2 On: +5V 2-3 On: (default) +5V_standby USB 2-3 (JP3) 1-2 On: Disable (default) 1-2 On: +5V 2-3 On: (default) +5V_standby USB 4-5 (JP5) 2-3 On: Enable 1-2 On: +5V 2-3 On: +5V_... -
Page 10: Clear Cmos Data
Chapter 2 Clear CMOS Data Super IO Select JP16 1-2 On: Enable JP12 1-2 On: Normal 2-3 On: Disable (default) (default) 2-3 On: Clear CMOS Data If you encounter the following, JP16 is used to select enable or disable the super IO select. a) CMOS data becomes corrupted. -
Page 11: Backlight Control Level Select
Chapter 2 Backlight Control Level Select MXM 5V Power Select JP15 1-2 On: 5VSB 1-2 On: +5V 2-3 On: +3.3V (default) 3-4 On: 5V 5-6 On: NC JP15 is used to select the backlight control level +5V or +3.3V. JP2 is used to select the power of the MXM connector. Chapter 2 Hardware Installation www.dfi... -
Page 12: Lvds Power Select
Chapter 2 LVDS Power Select USB Host/Client Select JP14 1-2 On: 12V 3-4 On: 5V 1-2 On: USB Client 2-3 On: USB Host 5-6 On: 3.3V (default) (default) JP7 is used to select between USB Host and USB client. JP14 is used to select the power of the LVDS connector. Chapter 2 Hardware Installation www.dfi... -
Page 13: Vga/Dvi Select
Chapter 2 VGA/DVI Select LAN2/PCIe x1 Slot Function Select 1-2 On: LAN 2 JP17 A1-2, J1-2 On: VGA (default) 2-3 On: PCIe x1 slot (default) JP18 1-2 On: LAN 2 (defaullt) A2-3, J2-3 On: JP17 is used to select the function of PCIe x1 slot or LAN 2. JP18 is just used to select the The system board allows connecting a device to either the DVI port or the VGA port at the LAN 2 function when pin 1 and 2 are set to On. -
Page 14: Bios Select
Chapter 2 BIOS Select 1-2 On: Boot from Carrier board SPI BIOS 1-2 Off: Boot from Module SPI BIOS J1 is used to determine the BIOS boot device. Chapter 2 Hardware Installation www.dfi .com... -
Page 15: Rear Panel Io Ports
BIOS Setting Configure the serial ports in the Advanced menu of the BIOS. Refer to chapter 3 for more information. Chapter 2 Hardware Installation www.dfi.com... -
Page 16: Vga Port
BIOS Setting Configure the display device in the Chipset menu (“North Bridge Configuration” submenu) of the BIOS. Refer to chapter 3 for more information. Chapter 2 Hardware Installation www.dfi.com... -
Page 17: Rj45 Lan Ports
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the +5V_standby power source of your power supply must support ≥1.5A. For 3 or more USB ports, the +5V_standby power source of your power supply must sup- port ≥2A. Chapter 2 Hardware Installation www.dfi.com... -
Page 18: Audio
Make sure pin 1 of the audio cable is aligned with pin 1 of the connector. The system board is equipped with 3 audio jacks. A jack is a one-hole connecting interface for inserting a plug. • Line-in/Surround Jack (Light Blue) This jack is used to connect any audio devices such as Hi-fi set, CD player, tape player, AM/FM radio tuner, synthesizer, etc. • Line-out Jack (Lime) This jack is used to connect a headphone or external speakers. • Mic-in/Center+Subwoofer (Pink) This jack is used to connect to the center and subwoofer speakers of the audio system. Chapter 2 Hardware Installation www.dfi.com... -
Page 19: Lvds Lcd Panel Connector And Lcd/Inverter Power Connector
Refer to the next page for the pin functions of these connectors. LVDS_CLK1+ LVDS_CLK2+ LVDS_CLK1- LVDS_CLK2- Jumper Settings Refer to the “Jumper Settings” section in this chapter for settings relevant to the LCD panel. LVDS_DDCCLK N.C. LVDS_DDCDAA N.C. Panel Power Panel Power Panel Power Panel Power Chapter 2 Hardware Installation www.dfi.com... -
Page 20: Digital I/O Connector And Digital I/O Power Connector
Its hot-plug functionality allows you to install and remove modules at any time, without having to switch off your system. This provides added reliability, durability and expansion flex- ibility to your system. DIO2 DIO3 DIO4 DIO5 DIO6 DIO7 Chapter 2 Hardware Installation www.dfi.com... -
Page 21: Sata (Serial Ata) Connectors
ATA cable to a SATA connector and the other end to your Serial ATA device. Power The fan connectors are used to connect cooling fans. The cooling fans will provide adequate airflow throughout the chassis to prevent overheating the CPU and system board components. Chapter 2 Hardware Installation www.dfi.com... -
Page 22: Chassis Intrusion Connector
Failure to do so will cause severe damage to the motherboard and components. intrusion occurred, an alarm will sound. When the system’s power is off and a chassis intrusion occurred, the alarm will sound only when the system restarts. Chapter 2 Hardware Installation www.dfi.com... -
Page 23: Power Connectors
RAM) state, it will blink every 4 seconds. Pin Pin Assignment Pin Pin Assignment PWR-LED N.C. LED Power N.C. LED Power HDD-LED HDD Power Signal Signal PWR-BTN Signal RESET SW Ground RST Signal Ground N.C. N.C. Chapter 2 Hardware Installation www.dfi.com... -
Page 24: Battery
Safety Measures • Danger of explosion if battery incorrectly replaced. • Replace only with the same or equivalent type recommend by the manufacturer. • Dispose of used batteries according to local ordinance. Chapter 2 Hardware Installation www.dfi.com... - Page 25 Chapter 2 LVDS_ _B3+ LVDS_ _B3- GBE_ _MDI2- GBE_ _MDI2+ GBE_ _LINK1000- LVDS_A_ _B_CLK+ GBE_ _MDI0- LVDS_A_ _B_CLK- GBE_ _MDI0+ LVDS_BLT_CTRL/GP_PWN_OUT0 RSVD GBE_ _ACT- LVDS_DID_DAT/GP_I2C_DAT LVDS_BLC_DAT(NC) GBE_ _S5- LVDS_DID_CLK/GP_I2C_CLK LVDS_BLC_CLK(NC) CAN0_ _S3- SDVO_ _INT+(NC) SUS_ SLP_ _BTN- SDVO_ _INT-(NC) SDVO_ _FLDSTALL+(NC) SDVO_ _FLDSTALL-(NC)
-
Page 26: I 2 C Connector
RAM. Controller Area Network (CAN or CAN-bus) is a message based protocol designed specifically for automotive applications but now is also used in other areas such as industrial automation and medical equipment. Chapter 2 Hardware Installation www.dfi.com... -
Page 27: Usb Client Connector
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a multiple device bus that allows multiple chips to connect to the same bus and enable each one to act as a master by initiating data transfer. Chapter 2 Hardware Installation www.dfi.com... -
Page 28: Lpc Connector
Chapter 2 LPC connector SD/MMC Slot LAD0 LAD1 VCC3 LAD2 RST# LAD3 SD/MMC Slot FRAME# This expansion port is used to insert a Secure Digital Input/Output (SDIO) or Multimedia Card The Low Pin Count Interface was defined by Intel ® Corporation to facilitate the industry’s tran- (MMC) device. -
Page 29: Spi Jtag Connector
This jumper is used to simulate the signal status that indicates the external battery is low. By setting to pins 1 and 2 to On, it sends a battery low signal to the module. Pin Pin Assignment Pin Pin Assignment 3V_standby Ground HOLOD- Chapter 2 Hardware Installation www.dfi.com... -
Page 30: Audio Drivers
“Next” each time you finish a step. 3. Click “Yes, I want to restart my computer now” then click Finish. Restarting the system will allow the new software installation to take effect. Chapter 3 Supported Software www.dfi.com... -
Page 31: Realtek Lan Drivers
Click Next. Change Destination Folder to select another folder. 2. Click Install to begin the 2. Click Install to begin installation. installation. 3. After completing installation, 3. Click Finish to exit installation. click Finish. Chapter 3 Supported Software www.dfi.com...